Fender TREAD-LIGHT VOL/EXP PEDAL User manual

TREAD-LIGHT™VOL/EXP PEDAL

1. Pedal
2. LED On/Off
Switch
3. Pedal Tension
Adjustment
4. EXP Out Jack
5. DC Power
Connector
6. Input Jack
7. Output Jack
8. Battery
Compartment
(not shown)
4567
1
2
3

Thanks for purchasing the Tread-Light Volume/Expression
Pedal, a versatile dual-purpose pedal with smoothly
uniform volume control and outstanding functionality with
a wealth of expression-compatible instruments and
devices. It features a rugged enclosure design with
stylishly old-school wood trim, easily adjustable
pedal-motion feel, a long-life potentiometer with a
rugged rack-and-pinion mechanism, and switchable LED
illumination for better onstage visibility.
DESIGNED IN CALIFORNIA, U.S.A.
TREAD-LIGHT™VOL/EXP PEDAL

Pedal
Pedal rocker motion can be loosened or tightened using Pedal
Tension Adjustment mechanism (below).
LED On/Off Switch
On/off toggle control for two blue LEDs beneath the pedal that
provide backlight illumination.
Pedal Tension Adjustment
Loosens or tightens rocker movement of pedal (see next page).
To avoid damage to pedal assembly, do not over-tighten.
EXP Out Jack
1/4“ expression output for use with expression-compatible
amps, effects and other instruments/devices.
DC Power Connector
Standard center-negative 9VDC jack for use with appropriate
power supplies.
Input Jack
1/4” input for electric guitar, bass, acoustic guitars with pickup
systems, keyboards and other instruments.
Output Jack
1/4” output jack connects to amp or next pedal in signal
chain.
Battery Compartment
Battery power is for backlight LEDs only; pedal functionality is
not dependent on battery power. Battery compartment cover on
underside of pedal snaps open and shut easily; compartment
houses single 9-volt battery that lifts out easily for replacement
(see next page).

Battery Compartment
Battery compartment cover on underside of pedal snaps open
and shut easily; compartment houses single 9-volt battery that
lifts out easily for replacement.

Pedal Tension Adjustment
To loosen or tighten rocker movement of pedal, pry cap from
right side of pedal with a small flat-head screwdriver; use
10mm socket wrench to adjust nut to pedal motion preference.
To avoid damage to pedal assembly, do not over-tighten.
CAP
NUT
Loosen Tighten

A PRODUCT OF
FENDER MUSICAL INSTRUMENTS CORPORATION
CORONA, CALIFORNIA, U.S.A.
Fender®is a registered trademark of FMIC.
Copyright © 2020 FMIC. All rights reserved.
PN 7720280000 REV. B
IMPORTANT SAFETY INSTRUCTIONS
•WARNING: To prevent damage, fire or shock hazard, do not expose the unit or its AC
power to rain or moisture.
•Do not alter the AC plug of the connected power adapter
•Do not drip or splash liquids on the unit.
•No user serviceable parts inside, refer servicing to qualified personnel only.
•WARNING: The unit must only be connected to a safety agency certified, regulated,
power source (adapter), approved for use and compliant with applicable local and
national regulatory safety requirements.
•Unplug AC power adapter before cleaning unit exterior. Use only a damp cloth for
cleaning; wait until the unit is completely dry before reconnecting to power.
•Amplifiers and loudspeaker systems, and ear/headphones (if equipped) are capable of
producing very high sound pressure levels, which may cause temporary or permanent
hearing damage. Use care when setting and adjusting volume levels during use.
ADDITIONAL LANGUAGES
Manual available in additional languages at
www.fender.com/support
Product specifications subject to change without notice
SPECIFICATIONS
IMPEDANCES
POWER SUPPLY
POWER REQUIREMENTS
POTENTIONETER
DIMENSIONS
WEIGHT
INPUT: 250kΩ
9V battery or 9VDC regulated adapter,
5.5 x 2.1 mm barrel connector, center negative
20mA @ 9VDC
Volume: 250kΩ reliable high cycle life
Expression: 100kΩ reliable high cycle life
8.25” x 3.45” x 2.68” (210mm x 88mm x 68mm)
1.65 lbs. (.75kg)

© FENDER MUSICAL INSTRUMENTS 2020