Ferve F-2507 User manual

1

2
BEFORE USING THE CHARGER READ THE OPERATING AND
SAFETY INSTRUCTIONS FOR BATTERY CHARGERS VIA THE
FOLLOWING LINK:
www.ferve.com/es/publicaciones.htm

CABLE WITH TERMINALS
pag.4
CONTENTS
pag.9
pag.14
pag.19
pag.22
pag.26
pag.29
3
BATTERY CHARGING
BATTERY MAINTENANCE
BATTERY CHARGING
BATTERY CHARGING
BATTERY RECOVERY
REPLACING A BATTERY

4
BATTERY CHARGING

Connect the clamps to the battery in the following
order: first the red clamp to the positive terminal + (A)
and then the black clamp to the negative terminal - (B).
Finally, connect the clamps to the charger (C).
If the clamps are reversed, the LED warning light
will turn on. Before continuing the charging process,
switch the position of the clamps.
Connect the FERVE F-2507 charger to a mains supply
(D). The LED POWER turns on and the charging
process begins.
5

Press the MODE button until the LED turns on.
The upper four LEDs indicate the
battery's charge status and they turn on progressively
as the charging proceeds.
6

Charge status table.
Example:
If the battery charge is lower than 25%, the first LED
flashes.
When the 4 LEDs are on solidly, the
battery is fully charged and the FERVE F-2507 can
now be disconnected.
7

Unplug the charger from the mains (A), then remove
the black clamp (B) and finally the red clamp (C).
If you leave it plugged in, the FERVE F-2507 auto-
charge will keep the battery at 100% capacity at all
times.
8

9
Function for charging AGM batteries.
Function for charging any kind of battery when the
temperature is below 3ºC.
BATTERY CHARGING

10
Connect the clamps to the battery in the following
order: first the red clamp to the positive terminal + (A)
and then the black clamp to the negative terminal - (B).
Finally, connect the clamps to the charger (C).
If the clamps are reversed, the LED warning light
will turn on. Before continuing the charging process,
switch the position of the clamps.
Connect the FERVE F-2507 charger to a mains supply
(D). The LED POWER turns on and the charging
process begins.
NOTE:
If the battery is not AGM, only use this function if the
temperature is below 3 °C.

11
The upper four LEDs indicate the
battery's charge status and they turn on progressively
as the charging proceeds.
Press the MODE button until the LED turns on.

12
Charge status table.
If the battery charge is lower than 25%, the first LED
flashes.
Example:
When the 4 LEDs are on solidly, the
battery is fully charged and the FERVE F-2507 can
now be disconnected.

13
Unplug the charger from the mains (A), then remove
the black clamp (B) and finally the red clamp (C).
If you leave it plugged in, the FERVE F-2507 auto-
charge will keep the battery at 100% capacity at all
times.

14
BATTERY CHARGING

15
Connect the FERVE F-2507 charger to a mains supply
(D).
Press the MODE button until only the LED POWER is
on.
Connect the clamps to the battery in the following
order: first the red clamp to the positive terminal + (A)
and then the black clamp to the negative terminal - (B).
Finally, connect the clamps to the charger (C).
If the clamps are reversed, the LED warning light
will turn on. Before continuing the charging process,
switch the position of the clamps.

16
Press and hold the MODE button for 3 seconds until
the LED turns on. The charging process starts.
The upper four LEDs indicate the
battery's charge status and they turn on progressively
as the charging proceeds.

17
Charge status table.
Example:
If the battery charge is lower than 25%, the first LED
flashes.
When the 4 LEDs are on solidly, the
battery is fully charged and the FERVE F-2507 can
now be disconnected.

18
Unplug the charger from the mains (A), then remove
the black clamp (B) and finally the red clamp (C).
If you leave it plugged in, the FERVE F-2507 auto-
charge will keep the battery at 100% capacity at all
times.
NOTE:
In the event of power failure, reselect the mode
on the charger.

19
Function recommended for keeping the battery at
100% charge capacity at a constant voltage.
BATTERY MAINTENANCE