Festool CLEANTEX CT 26 E User manual

702632_009
Festool GmbH
Wertstraße 20
D-73240 Wendlingen
Tel.: [phone]
Telefax: +49 (0)7024/804-20608
www.festool.com
Instruction manual
Page 6
IMPORTANT: Read all instructions before using.
Guide d’utilisation
Page 18
IMPORTANT: Lire toutes les instructions avant de démarrer les travaux.
Manual de instrucciones
Página 30
IMPORTANTE: Lea todas las instrucciones antes de usar.
Instruction manual
Guide d’utilisation
Manual de instrucciones
CT 26 E HEPA
CT 36 E HEPA
CT 48 E HEPA
DISTRIBUTED BY:
Pro Wood Finishes
14622 Southlawn Lane
Rockville MD 20850
Ph: [phone]

2
2-2
2-3
2-1
1-4
1-7
1-1
1-3
1-2
1-5
1-6
1-9
1-10
1-11
1-12
1-8
1

6
Contents
Symbols
About this manual
Save these instructions
It is important for you to read and understand this manual. The information it contains relates to protecting
your safety and preventing problems . The symbols below are used to help you recognize this information.
Symbols ............................................... 6
About this manual................................ 6
Safety instructions............................... 7
Technical data ...................................... 9
Functional description ......................... 10
Intended use ........................................ 10
Operation ............................................. 10
Settings................................................ 12
Working ................................................ 12
Filter..................................................... 13
After finishing work ............................. 15
Service and maintenance .................... 16
Accessories.......................................... 16
Disposal ............................................... 17
Sym-
bol
Significance
Warning of general danger
Risk of electric shock
Read operating instructions and safety
notices!
Wear a dust mask.
Tip or advice
Handling instruction
Wwatt
hhour
min minutes
sseconds
kg kilograms
Pa pascal
dB decibel
Vvolts
Aamperes
Hz hertz
~ a.c. alternating current
d.c. direct current
n
0
no load speed
Class II construction
rpm
min
-1
revolutions per minute
’’ inch
lbs. pound
diameter
Sym-
bol
Significance
DANGER Description of imminent haz-
ard and failure to avoid hazard
will result in death.
WARNING Description of hazard and
possible resulting injures or
death.
CAUTION Description of hazard and
possible resulting injuries.
NOTICE Statement including nature of
hazard and possible result.
HINT Indicates information, notes,
or tips for improving your suc-
cess using the tool.

7
Safety instructions
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basis precautions should always be followed, including the following:
READ ALL INSTRUCTIONS
BEFORE USING THIS DUST EXTRACTOR :
WARNING - To reduce the risk of fire, electric shock, or injury:
–Donotleavethedustextractorwhenplugged in. Unplug from outlet when not in use
and before servicing.
–Useindoorsonly.
–Donotallowtobeusedasatoy.Closeattention is necessary when used by or near
children.
–Useonlyasdescribesinthismanual.Use only manufacturer's recommended at-
tachments.
–Donotusewithdamagedcordorplug.Ifthe dust extractor is not working as it
should, has been dropped, damaged, left outdoors, or dropped into water, return it
to a service center.
–Donotpullorcarrybycord, use cord as a handle, close a door on cord, or pull cord
around sharp edges or corners. Do not run dust extractor over cord. Keep cord away
from heated surfaces.
–Donotunplugbypullingoncord.Tounplug,grasptheplug,notthecord.
–Donothandleplugordustextractorwithwethands.
–Donotputanyobjectintoopenings. Do not use with any opening blocked; keep free
of dust, lint, hair, and anything that may reduce air flow.
–Keephair,looseclothing,fingers,andall parts of body away from openings and
moving parts.
–Turnoffallcontrolsbeforeunplugging.
–Useextracarewhencleaningonstairs.
–Donotusetopickupflammableorcombustible liquids, such as gasoline, or use in
areas where they may be present.
–Connecttoaproperlygroundedoutlet only. See Grounding instructions.
–Donotpickupanythingthatisburningorsmoking,suchascigarettes,matches,or
hot ashes, hot chips or particles, sparks.
–Donotusewithoutdustbagand/orfiltersinplace.

8
SAVE THESE INSTRUCTIONS
GROUNDING INSTRUCTIONS
This appliance must be grounded. If it should malfunction or breakdown, grounding pro-
vides a path of least resistance for electric current to reduce the risk of electric shock.
This dust extractor is equipped with a cord having an equipment-grounding conductor
and grounding plug. The plug must be inserted into a appropriate outlet that is properly
installed and grounded in accordance with all local codes and ordinances.
WARNING - Improper connection of the equipment grounding conductor
can result in a risk of electric shock. Check with a qualified electrician or service person
if you are in doubt as to whether the outlet is properly grounded. Do not modify the plug
provided with the dust extractor - if it will not fit the outlet, have a proper outlet installed
by a qualified electrician.
This appliance is for use on a nominal 120-V circuit
and has a grounding attachment plug that looks like
the plug illustrated in sketch A in Figure beside.
Make sure that the appliance is connected to an out-
let having the same configuration as the plug. No
adaptor should be used with this appliance.
Polarization Instructions
To reduce the risk of electric shock, this vacuum
cleaner has a polarized plug (one blade is wider than
the other). This plug will fit in a polarized outlet only
one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not
fit, contact a qualified electrician to install the proper outlet. Do not change the plug
in any way.
Further safety instructions
–Thisappliancemustnotbeused by persons (including children) with reduced phys-
ical, sensory or mental capabilities, or lack of experience and knowledge. Children
need to be supervised to ensure they do not play with the appliance.
GROUNDED
OUTLET BOX
GROUNDED
PIN
GROUNDED
OUTLET
GROUNDING METHODS - SKETCH A
CAUTION
This machine is for indoor use only.
This machine shall be stored indoors only.

9
Health hazard by dust
WARNING! Various dust created by power sanding, sawing, grinding, drilling and other construction
activities contains chemicals known (to the State of California) to cause cancer, birth defects or other
reproductive harm. Some examples of these chemicals are:
•leadfromlead-basedpaints,
•crystallinesilicafrombricksandcementandother
masonry products, and
• arsenic and chromium from chemically treated
lumber.
The risk from these exposures varies,
depending on how often you do this type
of work. To reduce your exposure to
these chemicals: work in a well ventilated area, and
work with approved safety equipment, such as dust
masks that are specially designed to filter out micro-
scopic particles. Wash hands after handling.
Technical data
WARNING
TO REDUCE THE RISK OF INJURY, USER MUST
READ INSTRUCTION MANUAL.
Dust extractor CT 26 E, CT 36 E, CT 48 E
Power consumption (dust extractor only) 2.9 - 8.3 A (350 - 1000 W)
1
.)
Total connected load max. 12 A (1440 W)
Max. rating of connected Power Tool 3.7 A
2.)
Volume flow (air), turbine max. 234 m³/h (8264 cu.ft./h)
Vacuum, turbine max. 24000 Pa
Filter surface 6318 cm²(979.3 sq.in.)
Suction hose (diameter x length) 27 mm x 3.5 m (1-1/16" x 11.5’)
Protection type IP X4
Sound pressure level as per IEC 60704-2-1 71 dB(A)
Container capacity CT 26 E 26 l (6.9 gal.)
CT 36 E 36 l (9.5 gal.)
CT 48 E 48 l (12.7 gal.)
Dimensions L x W x H CT 26 E 630 x 365 x 540 mm
(24.8" x 14.4" x 21.3")
CT 36 E 630 x 365 x 596 mm
(24.8" x 14.4" x 23.5")
CT 48 E 715 x 392 x 680 mm
(28.1" x 15.4" x 26.8")
Weight CT 26 E 13 kg (28.7 lbs)
CT 36 E 14.4 kg (31.8 lbs)
CT 48 E 16.3 kg (35.9 lbs)
1. ) 8.3 A (1000 W) is the medium value for different operation conditions, a maximum power consumption of 10 A (1200 W) is possible.
2. ) When the suction power adjuster [1-7] is adjusted to the lowest suction power (see page 12, chapter Settings - Adjusting the suction
power) the maximal rating of a connected power tool can be 9.1 Amps.

10
Functional description
The pictures for the functional description are on a
fold-out page at the beginning of the instruction
manual. When reading of the manual you can fold
out this page for having always an overview of the
machine.
Accessories shown or described are sometimes not
included in the scope of delivery.
Intended use
The dust extractor is designed for use as specified
for the aspiration and evacuation of non-noxious
dusts, dirt, sand, shavings etc..
The dust extractor is designed as specified for vac-
uuming water.
The dust extractor is designed for household, com-
mercial or both use.
The dust extractor is designed for outdoor use and
indoor storage.
The filtering performance of the overall unit, which
is fitted with a HEPA filter element, corresponds to
HEPA quality 13 (medium degree of filtration
99.95%).
All CT extractors fitted with the HEPA filter element
have HEPA certification both for the filter material
and the whole dust extractor.
Operation
Consider the pictures on the fold-out page.
Initial operation
 Open the locking clips [2-2] and remove the top
section of the machine [2-1] .
 Remove the accessories from the dust contain-
er [2-3] and the packaging!
 Insert a filter bag in the dust container (see
chapter "Changing the filter bag").
 Attach the cable holder to the rear of the mobile
dust extractor (see Fig. [3] ).
[1-1] Intake opening
[1-2] Module slot
[1-3] Appliance socket
[1-4] Hose store
[1-5] Handle
[1-6] SysDoc
[1-7] Suction power adjuster
[1-8] Switch
[1-9] Locking clip
[1-10] Dust container
[1-12] Brake
WARNING
The user will be liable for damage due to improp-
er use.
WARNING
Unauthorised voltage or frequency!
Risk of accident
 The mains voltage and the frequency of the pow-
er source must correspond with the specifica-
tions on the machine's name plate.
 In North America, only Festool machines with
the voltage specifications 120 V/60 Hz may be
used.

11

Replace the top section [2-1] and close the
locking clips
[2-2] .
 Connect the suction hose to the machine.
Switch on/off
 Insert the plug into an earthed socket.
The switch [1-8] serves as an On/Off switch. It has
three positions:
Switch position "0"
Appliance socket [1-3] is disconnected from the
power, mobile dust extractor is switched off.
"MAN" switch position
Appliance socket [1-3] is disconnected from the
power, the mobile dust extractor starts.
"Auto" switch position
Appliance socket [1-3] is connected to the power,
the mobile dust extractor starts when the connect-
ed tool is switched on.
Extension Cord
If an extension cord is required, it must have suffi-
cient cross-section to prevent an excessive drop in
voltage or overheating. An excessive drop in voltage
reduces the output and can lead to failure of the
motor. The table below shows you the correct cord
diameter as a function of the cord length for this
tool.
Use only U.L. and CSA listed extension cords.
Never use two extension cords together. Instead,
use one long one.
 The lower the AWG number, the stronger the
cord.
The antistatic system
Friction inside the extraction hose causes static
electricity to develop during extraction. Operating
personnel may receive unpleasant electric shocks
while working. The mobile dust extractor is fitted
with an antistatic system as standard to discharge
any static electricity that may develop. However, al-
ways use the enclosed antistatic extraction hose.
CAUTION
Risk of injury from tools starting up unexpectedly
 Before setting the switch to the "AUTO" or
"MAN" position, make sure that the connected
tool is switched off.
3
Total Extension Cord
Lenght (feet)
25 50 100 150
Cable size (AWG) 14 12 not recom-
mended

12
Settings
Consider the pictures on the fold-out page.
Connecting electric power tools
 Connect the electric power tool to the appliance
socket [1-3] .
Connecting pneumatic tools
If the compressed air module [1-2] (496141) is in-
stalled, the automatic switch-on function of the
mobile dust extractor also works in combination
with pneumatic tools.
We also recommend installing the VE service unit
(495886). The service unit filters and lubricates the
compressed air and enables an adjustment of the
air pressure. An IAS adapter (454757) is available to
connect Festool pneumatic tools to the IAS system.
The operating pressure of the tool must be 6 bar for
the automatic switch-on unit to function correctly.
Temperature cut-out
To prevent overheating, a temperature cut-out
switches the mobile dust extractor off when it
reaches a critical temperature.
 Switch off the mobile dust extractor and allow to
cool for about 5 minutes.
 If the mobile dust extractor will not switch on
again, please contact a Festool service workshop.
Adjusting the suction power
You can use the suction power adjuster [1-7] to adapt
the machine suction power to different applications.
Applying the brake
Folding out the brake lever [1-12] prevents the mo-
bile dust extractor from rolling. To achieve this, lift
the front end of the mobile dust extractor slightly
and push the brake lever downwards until it latches
into place. Push the lever [1-11] again to release.
Working
Handling
Hose store: after finishing work, you can feed the
suction hose through the recess
[4-3] and place it
in the hose store. You can do the same with the
mains cable through the other recess
[4-2] .
SysDoc Systainer attachment system: a Systainer
can be attached to the storage area via the two
slides [4-1] .
WARNING
Risk of injury
 Observe the maximum appliance socket con-
nected load (see chapter "Technical data")
 Switch off the electric power tool.
WARNING
Risk of injury
 Make sure that the pneumatic tool is switched
off before connecting or disconnecting.
4
4-1 4-2
4-3

13
Extracting dry materials
Remember: A damp main filter will clog more
quickly when dry materials are extracted. There-
fore, dry the main filter before extracting dust or re-
place the damp filter with a dry one.
Extracting fluids
 The main filter shall only be used for extracting
dry materials.
Before extracting fluids, remove the filter bag (see
chapter "Changing the filter bag"). We recom-
mend using a special wet filter.
The dust extractor stops automatically when the
maximum level is reached.
Filter
Changing the filter bag
Inserting the filter bag
 Open the locking clips [2-2] and remove the top
section of the machine
[2-1] .
 Insert a new filter bag (SC-FIS-CT 26/36/48)
(Fig. [5] ) in the inlet port of the dust container
and interlock it.
Important: be aware that the
locking engages.
 Make sure that the filter bag is not pinched be-
tween the top and bottom sections.
 Replace the top section [2-1] and close the
locking clips [2-2] .
Removing the filter bag
 Open the locking clips [2-2] and remove the top
section of the machine [2-1] .
 Remove the filter bag (Fig. [6] ).
 Dispose of the used bag in accordance with stat-
utory regulations.
 Clean the dust container [2-3] .
 Insert a new filter bag if necessary (see Insert-
WARNING
Not suitable to vacuum hazardous or toxic sub-
stances or dusts e.g. asbestos.
 The filters will not be able to capture all particles
and may exhaust them back into the environment.
WARNING
Risk of injury
 Do not evacuate combustible liquids!
CAUTION
Escaping foam and fluids
 Switch off the machine immediately and empty
the dust container.
WARNING
Risk of injury
 During the following procedure, take care not to
raise dust more than is unavoidable. Moisten the
main filter with a water spray before removing it.
1
2
3
5
SC-FIS-CT 26/36/48