Fetco CBS-1150 EXTRACTOR V+ Specifications

USER’S GUIDE &OPERATOR INSTRUCTIONS
FETCO COFFEE BREWER: CBS-1150 EXTRACTOR
®
V+ ™
CBS-1151-XV+ CBS-1152-XV+
TABLE OF CONTENTS
Specifications and Requirements ................................ 2 
Rough-In Drawings ...................................................... 2 
Electrical and Output Specifications ............................ 3 
Starting The Brew ........................................................ 4 
Enter Programming...................................................... 4 
Exit Programming & Save............................................ 4 
PROGRAMMING MENU LAYOUT . ............................ 5 
A PROGRAM ............................................................... 6 
B GENERAL................................................................. 7 
C INPUTS .................................................................... 8 
D OUTPUTS ................................................................ 8 
E OTHER ..................................................................... 8 
F SAVE & EXIT............................................................ 9 
Error Codes .................................................................. 9 
Operator Training ....................................................... 10 
Cleaning & Maintenance ............................................ 10 
Installation Guide........................................................ 11 
Parts Diagrams CBS-1151V+ .................................... 14 
Parts Diagrams CBS-1152V+ .................................... 16 
CBS-1151V+ Tank Assembly..................................... 18 
CBS-1152V+ Tank Assembly..................................... 19 
Wiring diagrams ......................................................... 20
CONTACT INFORMATION
FETCO®
FOOD EQUIPMENT TECHNOLOGIES COMPANY
600 ROSE ROAD
LAKE ZURICH • IL • 60047-0429 • USA
INTERNET: www.fetco.com
©2017 FOOD EQUIPMENT TECHNOLOGIES COMPANY
PHONE: [phone] (US & CANADA)
[phone]
FAX: [phone]
EMAIL: [email protected]
[email protected]
PATENTS: WWW.fetco.com/patents
P167 REV:000 NOVEMBER 2017

Go to fetco.com for the latest versions of all information Page 2 P167 November 2017
.
Rough-In Drawings
CBS-1151 XV+ Front CBS-1152 XV+ Front CBS-1151 XV+&CBS-1152 XV+ Side
WIRING METHODS: REFERENCE ONLY: SEE THE WIRING DIAGR
A
MS AT BACK OF THIS GUIDE
CBS-1151 XV+ CBS-1152 XV+ factory configuration
208-240 volt single phase CBS-1152 XV+ *Field installed configuration
208-240 volt three phase connection
CBS 1151 XV+ Single phase—2 HEATER Three phase—3 HEATER
Field conversion is to be made only by licensed electrician. Disconnect equipment from
power suppl
y
before service. Remove
j
umper between L2 and L3, and appl
y
power to L3
Specifications and Requirements
Water Requirements: Coffee Filter Size:
CBS-1150 XV+ 20-75 psi
g
,
(
138-517kPa
)
1½
g
pm/
(
5.7lpm
)
15” X 5 ½ ”
–
standard FETCO # F001
Water supplied to hot beverage equipment should be filtered
Water supplied Hardness >100 TDS
(
5.5
g
rain
)
Temperature, as set by factory: 200°F
(
93°C
)
inside water tank
(
at sea level
)
Water inlet fittin
g
:3/8 inch male flare. Electrical: See electrical confi
g
uration chart.
Brew Volume: Full Batch 1 ½
g
allon/ 6 liters Up to 2
g
allon/7.7 liters per brew
Total Brew Cycle: Factory setting: 5.5 minutes consisting of 4 minute brew time + 1.5 minute drip delay
Brew-Process parameters are controllable :for: Brew Volume, Brew Time, Prewet Percent and Dela
y
, Drip Dela
y
JUMPER JUMPER
REMOVED

Go to fetco.com for the latest versions of all information Page 3 P167 November 2017
Electrical and Output Specificationsfor CBS-1151 XV+ Single 1½ Gallon-6 Liter Coffee Brewers
USA and Canada CBS-1151 XV+ Standard-Voltage With cUL/UL and NSF-4 certification
Configuration
Codes
Heater
Configuration Voltage Phase Wires Electrical Connection KW Maximum Amp Draw
Brew-Volume/Hour
(1½ gallon per batch)
E115151 2 X 3.0 kW 208-240 1 2+G Hardwired 4.6-6.1 22.4-25.8 15.3 gal/58 liters
North America & International Versions CBS-1151 XV+ With cUL/UL and NSF-4 Certification
E115190 1 X 4.0 kW 200-240 1 2+G Hardwired 4.1 14.2-17.1 9.3 gal/35 liters
E115191 1 X 5.0 kW 200-240 1 2+G Hardwired 5.1 17.7-21.3 12.7 gal/48 liters
E115192 2 X 3.0 kW 200-240 1 2+G Hardwired 6.1 21.3-25.5 15.3 gal/58 liters
E115193 2 X 2.3 kW 200-240 1 2+G Hardwired 4.7-6.1 22.1-25.5 14.0 gal/53 liters
Export/Japan XV+ With cUL/UL and NSF-4 Certification
E115180 1 X 5.0 kW 200-240 1 2+G Hardwired 3.6 17.7 11.6 gal/44liters
CE EXPORT/Japan CBS-1151 XV+ With CE and NSF-4 certification. Internal EMI filter. Not cUL and UL listed
(CE) E115162 2 X 2.3 kW 230/400 2 2L,N, Hardwired 5.6 12.4 14.0 gal/53 liters
(CE) E115161 2 X 3.0 kW 230/400 2 2L,N, Hardwired 6.1 21.3-25.5 15.3 gal/58 liters
. Specifications:-Electrical and Output for CBS-1152 XV+ Twin 1½ Gallon-6 Liter coffee brewers
USA and Canada CBS-1152 XV+ Field Select Electtical With cUL/UL and NSF-4 certification
Configuration
Codes
Heater
Configuration Voltage Phase Wires Electrical Connection KW Maximum Amp Draw
Brew-Volume/Hour
(1½ gallon per batch)
E115251
Selectable
Sold as1 phase
2 X 3.0 kW 208-240 1 2+G Hardwired 4.6-6.1 22.4-25.8 15.3 gal/58 liters
3 X 3.0 kW 208-240 3 3+G Hardwired 6.9-9.1 19.5-22.5 22.5 gal/85 liters
E115252
Selectable
Sold as1 phase
2 X 5.0 kW 208-240 1 2+G Hardwired 7.6-10.1 36.9-42.5 25.3 gal/97 liters
3 X 5.0 kW 208-240 3 3+G Hardwired 11.4-15.1 32.0-36.9 38.3 gal/145 liters
North America & International Versions CBS-1152 XV+ Standard-Voltage With cUL/UL and NSF-4
tifi ti
E115292 2 X 3.0 kW 208-240 1 2+G Hardwired 4.6-6.1 22.4-25.8 15.3 gal/58 liters
E115294 2 X 5.0 kW 208-240 1 2+G Hardwired 7.6-10.1 36.9-42.5 25.3 gal/97 liters
E115296 3 X 4.0 kW 240/415 3 4+G Hardwired 12.2 15.7-17.1 29.5 gal/112liters
E115290 3 X 3.0 kW
220/380
or
240/415 3 4+G Hardwired 9.1 11.8-12.9 22.5 gal/85 liters
E115291 3 X 5.0 kW
220/380
or
240/415 3 4+G Hardwired 15.1 19.5-21.4 38.3 gal/145 liters
Export/Japan CBS-1152 XV+ With cUL/UL and NSF-4 certification
E115280 3 X 3.0 kW 200 3 3+G Hardwired 6.5 18.6 17 gal/64 liters
CE EXPORT/Japan CBS-1152 XV+ With CE and NSF-4 certification. Internal EMI filter. Not cUL and UL listed
(CE) E115261 3 X 3.0 kW 230/400 3 3L,N,PE Hardwired 8.6 12.4 22.5 gal/85 liters
(CE) E115262 3 X 5.0 kW 230/400 3 3L,N,PE Hardwired 14.1 20.4 38.3 gal/145 liters

Go to fetco.com for the latest versions of all information Page 4 P167 November 2017
Starting The Brew
1. Turn the power switch “ON”.
2. Prepare a brew basket with the correct size filter and appropriate amount of coffee.
3. Slide the brew basket completely into the rails.
4. Place a clean, empty, preheated dispenser under the brew basket.
5. Select a batch & hold the corresponding BREW button in for 1 second to start
6. -STOP button will illuminate,
-Countdown time will display,
-Selected BREW button will flash to indicate brew is in progress.
-All other BREW buttons for that brew head will extinguish.
7. When the brew cycle is finished,
STOP button will extinguish and the BREW button will continue to flash for the amount
of time programmed into the DRIP DELAY setting.
This indicates that coffee may still be dripping from the brew basket
For safety- do not remove brew basket until drip-out is complete.
Twin Brewer ready to brew. Pressing top right brew position Brewing-see #6 above
Enter Programming
Screens shown are for twin brewer. Single brewer will not have menu A4-A6.
There are five menu
g
roups-
A
-E . See the followin
g
pa
g
es for the batch parameter definitions and all settin
g
s for the brewer
TO ENTER PROGAMMING
1-Turn brewer “OFF” from power switch
2-Turn power switch to “ON”
…Screen will initialize and then
display digital process notifications
3-After iitailization-Red “STOP” Lamp turns on
4-Quickly hold down “STOP” button for 5 seconds
When brewer is In PROGRAMMING MODE
-the screen will display:
|BATCH PRG|
|A (or B-E) |
-Illuminated LED indicates active keypad positions
See the following pages for batch parameter
definitions and all settings for the brewer
Turn power OFF
Turn power ON
Wait for red LED
And quickly hold down
STOP button on front
touch panel for 5 sec.
First screen will display
for PROGAMMING-A
Scroll through main menu
topics by pressing
“STOP” button.
Exit Programming & Save Control Setting Changes
From any screen-
Press STOP button
until the EXIT (“F”)
screen appears
From the “F” screen
Press button 2to
toggle to the EXIT-
Y
ES screen
From EXIT screen
Press button 1to
toggle to the SAVE
screen
From SAVE screen
Press button 2to
toggle to the SAVE-
Y
ES screen
To SAVE and EXIT
Press button 1to
SAVE your changes
and EXIT
READY BREW
05:30
STOP
STOP
STOP BUTTON
↓
ON/OFF switch
is located on
lower right on
back of brewer
LOADING
STOP
STOP
Batch PRG
A
STOP STOP
1
2
3
Programming A-F
A - F
STOP
STOP
1
2
3
EXIT
F NO +
STOP
STOP
1
2
3
EXIT
F YES -
STOP
STOP
1
2
3
SAVE
F NO +
STOP
STOP
1
2
3
SAVE
F YES -
STOP
STOP
READY READY
STOP
STOP

Go to fetco.com for the latest versions of all information Page 5 P167 November 2017
The A [1-3 or 1-6] menus correspond to the [3 or 6] batch buttons on the touch panel
Access the A menus to PROGRAM & make changes to individual menu recipes. Menu settings can be copied
Menu positions
A
1 and A4 [top position] are permanent. Menus A2, A3, A5, A6 can be removed b
y
operator if desired
From A PRG screen
Press button 1 to go to
the A menu access
screen
From A11 screen
Press STOP to scroll
to A20.
(A1&A4 are permanent)
From A20 screen
Press STOP to
scroll through the
remaining (3 or 6)
“A” menus. Make
any changes as
required
From A60 screen
Scroll out to
remaining A10-to
A70 programming
keys. See SAVE &
EXIT in previous
table
For single and twin
Position of batch
buttons
.
PROGRAMMING MENU LAYOUT
CBS XV+ Series
SINGLE TWIN
A1 top A1&A4
A2 center A2&A5
A
3 bottom
A
3&
A
6
A1. to A7 B1.0 to B1.7 C1.0 to C1.3 D1.0 to D1.5 E1.0 to E1.8
PROGRAM GENERAL INPUTS OUTPUTS OTHER
|
|
|
|
|
A_0
Batch Activate
|
|
|
|
|
|
|
|
|
A_1
Brew Volume B1 Tank Temp C1 LLC Probe D1 Test L.Brew Valve E1 Displa
y
Firmware
|
|
|
|
|
A_2
Brew Time B2 [Brew at Temp] C2 B. Basket Sensor D2 Test R.Brew Valve E2 Select Brewer Model
|
|
|
|
|
A_3
Prewet Percent B3 LLC Sensitivit
y
C3 Tank water temp. D3 Test Fill Valve E3 Displa
y
Errors
|
|
|
|
|
A_4
Prewet Dela
y
B4 Temperature F/ C C4 Ke
y
pad Test D4 Test Heater E4 Clear Errors
|
|
|
|
A_5
Drip Dela
y
B5 Volume unit G or L D5 Screen Bri
g
htness E5 Reload Defaults
|
|
|
A20
Batch Enable? B6 Left Flow Rate E6 Save throu
g
h USB
|
|
A30
Batch Enable? B7 Ri
g
ht Flow Rate E7 Load throu
g
h USB
|
|
A40
PERMANENT B8 Slow Mains Flow E8 Demo Mode
A50
Batch Enable?
A60
Batch Enable?
A70
Recipe Cop
y
?
Left top A11& Right top A41 are permanent
SEE BOX BELOW FOR ALL “A” menus
1
BATCH PRG
A
STOP
STOP
BREW VOLUME
A11 3.00L +
STOP
STOP
BREW ACT
A20 YES --
STOP
STOP
BREW ACT
A60 YES +
STOP
STOP
A4
A5
A6
(Twin model shown)
Batches A1-to A6
STOP
STOP
A1
A2
A3

Go to fetco.com for the latest versions of all information Page 6 P167 November 2017
.
RECIPE Location map
Viewing and changing settings for the brew
recipes is from the “A” screens with the controls
in PROGRAMMING.
The uppermost button positions are permanent
and will not display programming step A_0. The
table above shows in position A20 that a button
position can be made active or inactive.
Position A1 does not display this step
DISPLAY DISPLAY
STOP
BATCH A1
(permanent)
BATCH A4
(permanent)
BATCH A2BATCH A5
BATCH A3BATCH A6
A PROGRAM Menu Features: Batch Parameters
The settings below are shown for the top batch on a single brewer top left button on a twin brewer.
See how to access all A menus on the previous pa
g
e. Below are the brew settin
g
s for default A1 & A2 batches
POSITION Program Items Factory set
Defaul
t
Programming Range Increments Notes
A11 Batch Volume 1.5 gal
5.65 liters
0.50 to 2.00 gal
1.90 to 7.60L
0.01G
0.05L
Unit software is in liters;
converts to
g
allon
A12 Brew Time 4:00 minutes 2:00 – 12:00 0.30 Default total brew time is
5:30 minutes
A13 Prewet Perc. 0% 0.00 – 15.0% 1% Percentage of total brew
volume
A14 Prewet Delay
(Pause after prewet
completes)
0% [1:00 Min] [0:10 – 5:00] 1:00 min
The time between
prewetting and start of
brew cycle.
This feature appears
ONLY if Prewet >0:00
A15
This is a
Safety
Feature
Drip Delay 1:30 mm:ss 0:30 – 6:00 Min.
Time that brew basket
remains locked during final
drip-out
Drip delay remains “ON”
for 1:30 minutes if STOP
is pressed durin
g
brew †
A20
BATCH ACT
A20 YES -
NO +
YES
(Active)
Middle and Bottom
batches A2,3,5,6
Batch on
or off
Batches may be
individually enabled,
rewritten or deactivated
A21 Batch Volume 1.5 gal
5.65 liters
0.50 to 2.00 gal
1.90 to 7.60L
0.01G
0.05L
Unit software is in liters;
converts to
g
allon
A22 Brew Time 4:00 minutes 2:00 – 12:00 0.30 Default total brew time is
5:30 minutes
A23 Prewet Perc. 0% 0.00 – 15.0% 1% Percentage of total brew
volume
A24 Prewet Delay
(Pause after prewet
completes)
0% [1:00 Min] [0:10 – 5:00] 1:00 min
The time between
prewetting and start of
brew cycle.
This feature appears
ONLY if Prewet >0:00
A25
This is a
Safety
Feature
Drip Delay 1:30 mm:ss 0:30 – 6:00 Min.
Time that brew basket
remains locked during final
drip-out
Drip delay remains “ON”
for 1:30 minutes if STOP
is pressed durin
g
brew†
Batch Cop
y
Cop
y
From Batch
A
71
A
71 1
(
1-6
)
Cop
y
To Batch?
A
72
A
72.1
(
1-6
)
*Topmost Batch cannot be disabled. *Topmost Batch LEFT & RIGHT Side cannot be disabled.
**Middle and bottom batches may be disabled for single and twin brewer (CBS-1151 XV+ and CBS-1152 XV+)
† DRIP DELAY will not activate when STOP is pressed within 5 seconds of startin
g
a brew time
A1
A2
A3
Single Side Models
CBS-1151 V+
STOP
A4
A5
A6
Twin Models
CBS-1152 V+
STOP
A1
A2
A3
STOP

Go to fetco.com for the latest versions of all information Page 7 P167 November 2017
B GENERAL Brewer Operation Control Settings, Adjust Brew Flow Rate
POSITION Program Items Factory set Default Programming
Ran
g
e Increments Notes
B1 Tank Temp.
93° C -or- 200°F
NOTE: Equipment
is metric b
y
default
70° to 96°C
157°F to 205°F
0.5°C
1.0°F
See below
for chart to correct
for hi
g
h altitude
B2 Brew at Temp. “YES” ON/OFF YES/NO SEE NOTE BELOW
B3 LLC Sensitivity LOW
LOW is
“normal” for
most water
“HIGH” for R.O.
LOW
or
HIGH
Liquid level control
sensitivity.
High is for reverse
osmosis water or very
pure water.
B4 Temperature Scale °C
De
g
rees Celsius
Equipment is
metric by default C/F [Switchable Units]
B5 Volume Scale Liters [Gallons] Equipment is
metric by default L/Gal [Switchable Units]
B6 LEFT brew valve
Flow Rate:
CBS-1152
3.40L/0.9G
2.9-3.9Liter
0.73-1.01Gallon
0.50L
0.01Gal Adjusts flow rate
B7 RIGHT brew valve
Flow Rate:
CBS-1151&1152
3.40L/0.9G
2.9-3.9Liter
0.73-1.01Gallon
0.50L
0.01Gal Adjusts flow rate
B8 Low flow rate
from mains NO OFF/ON
Toggle =/-
YES or NO
Trims fill system for
low supply
Chart to correct for altitude for boiling point
in tank water temperature.
[ft] [m]
Suggested
Setting[°F] Boiling point[°F] Suggested Setting[°C] Boiling point [°C]
0 0 205 212.0 96 100.0
500 152 205 211.0 96 99.5
1000 305 200 210.1 93 98.9
2000 610 200 208.1 93 97.8
2500 762 200 207.2 93 97.3
3000 914 200 206.2 93 96.8
3500 1067 197 205.3 92 96.3
4000 1219 195 204.3 91 95.7
4500 1372 194 203.4 90 95.2
5000 1524 194 202.4 90 94.7
5500 1676 193 201.5 89 94.2
6000 1829 192 200.6 89 93.6
6500 1981 191 199.6 88 93.1
7000 2134 190 198.7 87 92.6
7500 2286 188 197.8 86 92.1
8000 2438 187 196.9 86 91.6
8500 2591 185 196.0 85 91.1
BREW AT TEMPERATURE DEFINITONS
- --------------------------------------------------------------------------------------------------------
DEFAULT: BREW AT TEMP: “ON”
(FACTORY DEFAULT FOR BREWER)
“BREW at TEMP:
-Batch will not start if tank temperature is
below set point.
-Display will show “HEATING” and hot
water tank temperature
The “BREW START” entry buttons will not
illuminate until the hot water tank reaches
the selected temperature.
Control will allow both sides of dual brewer to operate if one side has
an ongoing brew started and the second side brew is selected.
Notifications shown on screen:
TEXT: HEATINGTank above 87°C/189°F-will allow brew at low
temperature. Coffee flavor may be affected
TEXT: L. HEATTank above 76°C/169°F-will allow brew at low
temperature. Coffee flavor will be noticably affected
------------------------------------------------------------------------------------------------------
USER SELECTABLE OPTION: BREW AT TEMP: OFF
(Not recommended)
Allows brewing at any temperature above 77°C/170°F
Below 70°C/170°F The red colored ready lights switch turn off-unit
will operate at cold
Hot water tank
not at temp.
Tank temp
STOP is not lit 
BREW START
buttons not lit.
and are disabled.
Buttons will
reilluminate when
“READY”
HEATING
160°F
STOP STOP
Use this formula to compensate for minor discrepancies in actual volume versus programmed volume.
Default Brew Valve Flow Rate—All CBS-1150 V+ Brewers
CBS-1151 &CBS-1152 ml/min Range
Left and Right Brew Valve FR 3400 ml +2903 to 3900ml
Use the formula above to determine the correct setting Set lower to increase volume, higher to decrease volume.
See “PROGRAM” B5 and B6 For valve settings and calibration. Factory set brew valve flow rates are in liter/min

Go to fetco.com for the latest versions of all information Page 8 P167 November 2017
D OUTPUTS Test Valves and Heaters-Set screen brightness
POSITION Program Items Factory set
Defaul
t
Programming Range Increments Notes
D1 Left Valve Test (Press To Test) TEST Toggle +/-
OFF or ON
Runs valve to verify
flow. NOTE!-Have
container under
brew-basket!
RIGHT Valve display is only for CBS-1152 XV+ twin side brewer. Single series displays LEFT side only
D2 Right Valve Test (Press To Test) TEST Toggle +/-
OFF or ON Press To Test
D3 Fill Valve Test (Press To Test) TEST Toggle +/-
OFF or ON Press To Test
D4 Heater Test (Press To Test) Activates heaters 3
seconds
Toggle +/-
OFF or ON
Energizes
Heater(s)
WARNING! Service
use onl
y
.
D5 LCD Brightness Brightness=8 0-15 1 Very dim to bright
illumination
. E OTHER Software & Code View and Settings
POSITION Pro
g
ram Items Factor
y
set Defaul
t
Pro
g
rammin
g
Ran
g
e Increments Notes
E1 Display Firmware 0.1a
Displays current
version
E2 Select Model CBS-1152 XV+ Scroll to brewer
model Save&Exit
CBS-1151;
CBS-1152 Will need reboot
E3 Display Errors Lists up to six
codes, in order 1: ; 2: ;3:;4: ;5: ;6: Newest=Last
See Error Code
Chart for
references
E4 Reset Errors NO + Toggle +/-
YES or NO
Factory and
Service use only.
Do Not Rese
t
Resetting error codes should be after completing the service and factory diagnostics and correcting any brewer faults
NOTE Clear error codes by cycling the brewer “OFF” then “ON”. See Page 9.
E5 (Reload) DEFAULTS Reset to default of
base model Will need reboot Toggle =/-
YES or NO
COMPLETELY
OVERWRITES ALL
USER SETTINGS.
E5 USB Data Save Save data to USB
E6 USB Data Load Load Data from
USB Will need reboot
E7 Load From USB Plug in USB flash-
drive device. Will need reboot
E8 DEMO Mode DEMO ON/OFF Will need reboot
Demonstrates the
controls for training.
Disables all components
in demo mode
.
C INPUTS Brewer Sensors and Keypad
POSITION Program Items Factory set Default Programming Range Increments Notes
C1 LLC Probe
Continuit
y
Direct read Reading of tank water resistivit
y
in TDS
≈850- LOW
≈1600-HIGH Nominal values
C2 Brew Basket
Sensor Direct read YES or NO
C3 Tank Temperature Direct read Hot water tank
temperature Actual values
C4 Keyboard Test Calibrate Checks buttons under
membrane cover YES/NO
Follow directions
on the touch
screen

Go to fetco.com for the latest versions of all information Page 9 P167 November 2017
Error Codes
DO NOT CLEAR ERROR CODES UNTIL ERROR IS IDENTIFIED AND CORRECTED
 Contact specialized personnel for error codes
Code Description Possible Cause Corrective Action
001
Software error-error on start up or
corrupted software
Improper start-up or
shutdown
Restart , if still fault: reload software
050 Short-circuit in temperature probe Probe failure. Replace probe.
051 Open temperature probe. Bad probe connection, or
probe failure.
Check all connections. Replace probe
if necessar
y
.
100
Initial Fill Error. Initial fill time was
more than 11 minutes after power
up.
Water supply flow rate is
too low.
Watch for short potting during brew
cycle. Investigate cause of low flow
rate.
(
Clo
gg
ed water filter...
)
101 Error on refill
Tank did not refill within 3 minutes.
Water supply flow rate is
too low.
Watch for short potting during brew
cycle. Investigate cause of low flow
rate.
(
Clo
gg
ed water filter…
)
201 Heater open, high limit thermostat,
or Solid State Relay (SSR) fault
Failure of: heating
element, SSR, high Limit
or low volta
g
e
Check and replace heating elements if
necessary.
255 Touch pad error
Usually from longer than 2
min contact. Or faulty
reassembly after service
Restart , if still fault: reload software.
If mechanical: reassemble correctly
NO
BSKT
Insert Brew Basket
Brew basket must be in
place
This is a
SAFETY FEATURE
Insert brew basket into brewer rails to
enable brewer
F SAVE & EXIT Saving changes and exiting PROGRAMMING
The brewer will save changes only from the “F” menu. Do not reboot brewer or toggle ON/OFF-exit as below.
TO EXIT PROGRAMMING & HOW TO SAVE CONTROL SETTING CHANGES
The brewer is in PROGAMMING mode, how to save changes and EXIT .
From any screen-
Press STOP button
until the EXIT (“F”)
screen appears
From the “F” screen
Press button 2to
toggle to the EXIT-
Y
ES screen
From EXIT screen
Press button 1to
toggle to the SAVE
screen
From SAVE screen
Press button 2, to
toggle to the SAVE-
Y
ES screen
To SAVE and EXIT
Press button 1to
SAVE your changes
and EXIT
NOTE: User Settings will be erased and overwritten to factory default settings by the following five programming changes
When setting or changing units of display for the tank temperature (F Fahrenheit or C Celsius). (SETTING B4)
When setting or changing units of display for the volume (G gallons, L liters). (SETTING B5)
When setting brewer model The software sets equipment to brewer defaults (SETTING E2)
When resetting (Reloading) DEFAULTS (SETTING E5)
When loading from USB (Reloads to defaults ) (SETTING E7)
1
2
3
Programming A-F
A - F
STOP
STOP
1
2
3
EXIT
F NO +
STOP
STOP
1
2
3
EXIT
F YES -
STOP
STOP
1
2
3
STOP
STOP
1
2
3
SAVE
F YES -
STOP
STOP

Go to fetco.com for the latest versions of all information Page 10 P167 November 2017
Operator Training
Review the operating procedures with whoever will be using the brewer.
Pay particular attention to the following areas:
1. Always pre-heat the dispensers before the first use of each day by filling them half way with hot water, and letting
them stand for at least 5 minutes. Drain, and begin first brew
2. Make sure the dispenser is empty before brewing into it..
3. Show how to attach covers, close, and or secure the dispensers for transporting.
4. Do not remove the brew basket from a coffee brewer until it has stopped dripping.
5. Show the location and operation of the water shut off valve as well as the circuit breaker for the brewer.
6. Steam from the tank will form condensation in the vent tubes. This condensation will drip into and then out of the
brew baskets. Up to 1/4 cup/118cc discharging overnight is possible. Place an appropriate container under each
brew basket when not in use.
7. We recommend leaving the power to the brewer on overnight. The water tank is well insulated and very little
electricity is used to keep the tank hot. Leaving the brewer in the “ON” position will also avoid delays at the beginning
of shifts for the brewer to reach operating temperature.
Cleaning & Maintenance
After Each Brew:
1. Dispose of used coffee filter and grinds and rinse brew basket.
2. Never strike a brew basket or hit it against a hard surface.
This will damage the brew cone, and may damage the brew basket support rails
3. Rinse dispensers before reuse.
Every Day:
1. Wash brew basket with hot sudsy water.
2. Pull CSD from the spray head, it is magnetically attached. Use gloves or a heavy towel. Wash
off any film and reattach. Use vinegar if limescale filming is present.
3. Clean dispensers with hot suds water and a brush, rinse and air dry.
4. Use only a soft cloth and hot suds on the outside to avoid scratches. Never use abrasives that will scratch surface.
Weekly
1. Use a commercial coffee dispenser cleaner such as URNEX™, TABZ™, DIP-IT™ or Squeak 'n Clean™.
2. Carefully Follow the instructions supplied with the cleaning product
3. Never use spray cleaners, solvent, solvent based cleaner or petroleum based polish anywhere on dispensers
Warning
1. Turn off power before any cleaning procedure, including wiping the exterior for appearance reasons.
2. Dry the exterior, especially the face panel, before turning on power.
3. Do not apply any type of spray cleaner on the face panel of this equipment.
4. Never use solvent or solvent-based cleaner or petroleum based polish anywhere on this equipment.
5. Dry the face of the touch pad before turning on power
6. Do not electrically energize this equipment or attempt operation without all covers in place and all screws fastened.
7. Unplug machine before disassembly or servicing.
Safety Notes
1. Professional installation is required. This appliance is manufactured only for commercial use
2. Operational requirements and maintenance for commercial cooking appliances differ from household appliances.
3. Operators must be trained for this equipment and must understand the use, maintenance and hazards.
4. Access to the service area is restricted to persons having safety/hygiene knowledge and practical experience of the
coffee brewer. This appliance must be installed in locations where it can be overseen by adult trained personnel.
5. Do not attempt to move hot beverage equipment once it is filled. Drain equipment before moving.
6. FETCO commercial coffee brewers prepare large amounts of coffee or tea in a single batch using very hot water
7. Commercial coffee brewers provides very hot water from the sprayhead, brew basket and faucet when it is pulled.
8. Brewers may continue to dispense very hot water from the mechanically operated faucet after the electronic touchpad is
completely disabled by turning off the power switch on the lower back of the unit, or unplugging the unit.
9. For safety, do not remove brew basket during the brew.
Keep these instructions for training and future reference.

Go to fetco.com for the latest versions of all information Page 11 P167 November 2017
Installation Guide
(For Qualified Service Technicians Only)
General:
1. If not installed correctly by qualified personnel, the brewer will not operate properly and damage may result.
2. Utilize only qualified beverage equipment service technicians for service and installation.
3. Always have an empty dispenser under sprayhead of all coffee brewing equipment-including when at idle
4. Damages resulting from improper installation are not covered by the warranty, and will void the warranty.
Electrical:
1. All FETCO brewers require an electrical ground wire. Installation without grounding is dangerous.
2. Note Equipotentiality Terminal, if present, (To identify the terminals which, when connected together, bring the various parts
of equipment or of a system to the same potential, not necessarily being the earth (ground) potential, e.g. for local bonding.)
3. Verify voltages, polarity, circuits, and circuit breaker access before attaching equipment.
4. Brewers in this series wire differently in regards to a neutral wire. Review the wire diagrams.
5. The electrical diagram is located in the Users Guide and online at www.fetco.com.
6. Make sure of the tight grounding of the equipment and use the external ground bolt.
7. The installation must comply with applicable federal, state, and local codes having jurisdiction at your location.
Check with your local inspectors to determine what codes will apply.
See wiring diagrams for connections
Plumbing:
1. North America: All installations must comply with applicable federal, state, or local plumbing codes.
2. All Others: The water and waste piping and connections shall comply with the International Plumbing Code 2003,
International Code Council (ICC), or to the Uniform Plumbing Code 2003 (IAPMO).
3. Use an inline water filter for all beverage equipment.
4. Install the filter unit after a water shutoff valve and in a position to facilitate filter replacement.
5. The water line and newly installed filter cartage must be flushed thoroughly prior to connecting it to the brewer to
prevent debris from contaminating the machine.
6. Verify that the water line will provide a flow rate of at least 1½gpm/(5.7lpm) per minute and the water pressure is
between 20-75 psig (138-517kPa) before making any connections.
7. Use a wrench on the factory fitting when connecting the incoming water line. This will reduce stress on the internal
connections and reduce the possibility of leaks developing after the install has been completed
8. Install a backflow prevention device. Most municipalities require a recognized backflow preventer.
Usable on all hot beverage and cold beverage equipment is a WATTS® SD-2 or SD-3.
WATTS spring loaded double check valve models are accepted by most zoning authorities.
The check valve should be as close to the water supply inlet of the beverage equipment as possible.
Tank Drain
The water tank must be drained before maintenance procedures, and when the unit is to be relocated or shipped
1.Disconnect power and water to unit. DANGER: Insure that all utility connections to the brewer are broken.
2.Move the unit near a sink or obtain a container large enough to hold four gallons of water.
Note: the hot water tank may hold more than four gallons.
3.Remove the front panel and tank cover and allow the tank to cool to a safe temperature
4.The tank drain line and clamp are located inside-under the hot water tank. Pinch the drain line clamp to close
5.Locate the fill valve against the back wall, using pliers, loosen the hose clamp and move it back over the tube.
Note Do not losen the hose clamp to the bottom of the hot water tank
6.Crimp the tube an inch or two away from the drain plug to prevent water from flowing and pull it off the valve.
7.Pull the tube end out of the brewer and position over sink or bucket.
8.Release the crimped tube and hose clamp and allow the water to flow into the sink or container.
9.Multiple buckets may be needed during the draining, see tank volumes below.
Brewer Hot Water Tank Capacity OPEN
Leave open for use
PINCH SHUT
To drain tank & service brewer
AI !
CBS-1151 XV+ Single 6.3 gal 24 liter
CBS-1152 XV+ Twin 11.5 gal 44 liter

Go to fetco.com for the latest versions of all information Page 12 P167 November 2017
Layout of the brewer
Operation and service Operation
.
Service
Layout for installing brewer
Touch-screen
(
for brewer operation
)
Brew basket sensor
(
internal
)
Brew basket
Hot Water Service Faucet
Airpot or Dispenser Locator
Main power switch
Installation safety and hygiene directions-For International and CE equipment
1. Access to the service area is restricted to persons having safety/hygiene knowledge and practical experience of the coffee
brewer. This appliance must be installed in locations where it can be overseen by trained personnel.
2. For proper operation, this appliance must be installed indoors where the temperature is between 10°C/50°F to 35°C/95°F.
Drain and remove all liquid from equipment and lines if exposed to freezing temperatures.
3. All commercial cooking equipment, including this unit, is not intended for use by children or persons with reduced physical,
sensory, or mental capabilities. Ensure proper supervision of children and keep them away from the unit.
4. Children should be supervised to ensure that they do not play hot beverage equipment.
5. This unit must be installed and serviced by qualified personnel only.
6. Installation must conform to all local electrical and plumbing codes. Installation by unqualified personnel will void the unit
warranty and may lead to electric shock or burn, as well as damage to unit and/or its surroundings.
7. If the power cord requires repair or replacement-it must be performed by the manufacturer or authorized service personnel
with the specified cord only from the manufacturer in order to avoid a hazard.
8. Review the dimensions for the unit and verify that it will fit properly in the space intended for it. Verify that the counter or
table will support the total weight of the brewer and dispensers when filled (See: Technical Data).
9. Place the brewer on the counter or stand. When the brewer is in position, level it front to back as well as side-to-side by
adjusting the legs.
10. Brewers will need a sturdy supported surface for operation. Do not move brewers when filled.
11. Do not tilt appliance more than 10° to insure safe operation.
12. Unit is for protected indoor use only. Do not steam clean or use excessive water on unit.
13. This unit is not “jet-proof” construction. Do not pressure wash or use jet spray to clean this unit.
14. The unit is not waterproof-do not submerge or saturate with water.
Equipment exposed to flood and contaminated must not be used due to electrical and food safety.
Do not operate if unit has been submerged or saturated with water.
Labels and
warnings for hot
beverage
equipment
For BACK PANEL
of equipment
(1046.00035.00)

Go to fetco.com for the latest versions of all information Page 13 P167 November 2017
1102.00223.01 Large Spray Assembly Parts CBS-1151 & CBS-1152 XV+
Ref QTY PART NO DESCRIPTION
1 1 1102.00116.00 LARGESPRAY HOUSING ASSEMBLY
2 1 1102.00222.00 VALVE, BREW, ASSEMBLY, 24 VDC
3 4 1082.00056.00 SCREW, #8-11 X 1" THRD FORM, P/H PHIL
4 1 1102.00043.00 CASCADE SPRAY DOME ASSY, CBS-1150'S
1000.00108.00 Brew valve rebuild kit
CONTAINS:
PLUNGER
SPRING
LARGE BREW VALVE DIAPHRAGM
Brew Baskets
Complete Brew basket Part Number B015280BN2 CBS-1151 & CBS-1152 XV+
Brown colored insert
is standard
Brew basket handle plug
for polymeric brew
baskets is available in
optional colors.
Part Number Plug Insert color
1023.00195.00 BROWN PLUG, BB HANDLE
1023.00194.00 BLACK PLUG, BB HANDLE
1023.00190.00 RED PLUG, BB HANDLE
1023.00191.00 GREEN PLUG, BB HANDLE
1023.00192.00 ORANGE PLUG, BB HANDLE
1023.00180.00 BLUE PLUG, BB HANDLE
OPTIONAL Stainless Steel Brew Basket
Ref# Qty Part Number Description
B001280B1 COMPLETE STAINLESS STEEL BREW BASKET
1 1 1112.00058.00 BREW BASKET WELDMENT (CONE ONLY)
2 1 1046.00025.00 BREW BASKET WARNING LABEL
3 1 1082.00040.00 SCREW,1/4-20X.5,FL-HD,PH.,W/NYLON PATCH
4 1 1009.00005.00 WIRE BASKET
5 1 1102.00064.00 HANDLE W/MAGNET ASSEMBLY, BLACK
Optional colored
handle
1102.00065.00 HANDLE W/MAGNET ASSEMBLY, RED
Optional colored
handle
1102.00066.00 HANDLE W/MAGNET ASSEMBLY, GREEN
Optional colored
handle
1102.00067.00 HANDLE W/MAGNET ASSEMBLY, ORANGE
1
5
3
4
2
1
2
3
4

Go to fetco.com for the latest versions of all information Page 14 P167 November 2017
Parts Diagrams CBS-1151V+
Table of authorities for CBS-1151XV+ models
SKU No. TANK ASSY WIRING DIAG. CONN. CLAMP
E115151 1104.00061.01 1401.00147.00 1086.00008.00
E115161 1104.00061.01 1401.00159.00 1086.00031.00
E115162 1104.00096.01 1401.00159.00 1086.00031.00
E115180 1104.00095.01 1401.00152.00 1086.00008.00
E115190 1104.00097.01 1401.00153.00 1086.00008.00
E115191 1104.00095.01 1401.00153.00 1086.00008.00
E115192 1104.00061.01 1401.00154.00 1086.00008.00
E115193 1104.00096.01 1401.00154.00 1086.00008.00

Go to fetco.com for the latest versions of all information Page 15 P167 November 2017
Re
f
Qty Part Numbe
r
Description Drawing 1101.00342.00 ASSEMBLY, CBS-1151 XV+
1 1 1111.00088.00 WELDMENT, COMPLETE, CBS-1151 XXV+
2 1 1057.00043.00 SOLENOID VALVE, 5.5L/min, 180 DEG, 24VDC
3 2 1083.00005.00 WASHER, M4 18-8 INTERNAL TOOTH LOCKWASHER
4 2 082.00010.00 SCREW, M4x10 ZINC-PLATED PAN HD. PHILLIPS MACH.
5 1 1102.00243.00 ADAPTER ASSY, 3/4" BSP x 1/4" NPT x 3/8" TUBE
6 8 1081.00006.00 SPACER, 6MM OD x 3.2MM ID x 5MM LG, Z/P
7 1 1052.00001.00 POWER SUPPLY, 90-264VAC/24VDC, 1.8A
8 4 1029.00012.00 SPACER, .25" HEX X 1" LG, FEM #4-40 THREAD
9 1 1112.00268.00 WELDMENT, BRACKET TERMINAL BLOCK, 4 POLE
10 5 1083.00011.00 WASHER, #8 SCREW SIZE, INTERNAL TOOTH LOCK
11 13 1084.00006.00 NUT, 8-32 18-8 HEX MACHINE SCREW
12 1 1052.00023.00 EUROSTRIP HE16 TERMINAL BLOCK, 4 POLE, 63 AMP, 18-8 AWG
13 1 1052.00025.00 PLATE, MARKING #BS1016E
14 2 1082.00082.00 SCREW, PHILLIP HD., 8-32 THREAD
15 1 1065.00009.00 GROUND LUG CONNECTOR, 14-2 AWG, ALUMINUM
16 1 1044.00012.00 LABEL GROUND, CE
17 1 1058.00024.00 SWITCH, POWER, DOUBLE POLE, 16A, 125/250 VAC
18 1 1046.00051.00 LABEL, "WARNING, EXTREMELY HOT WATER"
19 1 1071.00055.00 FAUCET, HOT WATER, PSC-BR-8, WITH FLAT AND STEM
20 1 1084.00048.00 JAM NUT, 1/2-20 UNF, NICKEL PLATED BRASS
21 1 1102.00375.00 ASSEMBLY, FRONT PANEL, CBS-1100 SINGLE
22 1 1083.00009.00 WASHER, #6 SCREW , INTL TOOTH LOCKWASHER
23 1 1084.00010.00 NUT, HEX, #6-32, UNDERSIZED, ZINC PLATED
24 1 1102.00223.01 SPRAY HOUSING, LARGE, 24 VDC, STRONGER COIL
25 6 1083.00010.00 WASHER, #10 SCREW W/NEOPRENE-BONDED SEAL
26 1 1025.00021.00 TUBE, 31/32"OD X 5/8"ID X 4 1/4"LG, BREW
27 1 1086.00018.00 HEYCO HOSE CLAMP DIA. .875-1.00
28 1 1086.00017.00 HEYCO HOSE CLAMP DIA .1.031-1.187
29 1 1102.00113.00 SWITCH, REED, ASSEMBLY
30 1 1029.00006.00 NUT, FINGER, #4-40 NYLON
31 1 1025.00082.00 TUBE, 5/8"OD X 3/8"ID X 19.00"LG.
32 4 1086.00003.00 UNICLAMP, 15.9 HOSE OD CLAMP
33 1 1025.00058.00 TUBE, 9/16"OD X 5/16"ID X 25.00"LG
34 1 1086.00009.00 CLAMP, 3/4" MAX TUBE OD FLOW CONTROL
35 11 1084.00011.00 NUT, CLIP ON (J-NUT), #6-32, 22-20 GA., BLK-PH FINISH
36 1 1001.00362.00 COVER, TOP, CBS-1151 EXTRACTOR XV+
37 12 1082.00017.00 SCREW, TRUSS HD. PHIL. MACHINE, # 6-32 X 1/2 LG.
38 1 1001.00363.00 COVER, UPPER BASE, CBS-1151 EXTRACTOR XV+
39 1 1402.00097.01 HARNESS, LOW AMP, CBS-1151-XXV+, UL
39 1 1402.00061.01 HARNESS HIGH AMP
39 1 1402.00050.01 HARNESS HIGH AMP CE
40 1 1112.00470.00 WELDMENT, RIGHT COVER, CBS-1150 XXV+
41 1 1024.00098.00 VENT TUBE, XTS AND 11XX
42 1 1058.00055.00 USB CONNECTOR
43 1 1084.00024.00 . NUT, CLIP ON (J-NUT), #6-32, 1050 SPR. STL
44 1 1046.00035.00 LABEL, WARNING "TO REDUCE RISK OF ELECTRIC SHOCK OR FIRE"
45 1 1041.00031.00 LABEL, EXTRACTOR XV+ LOGO
46 1 1046.00003.00 LABEL, CSD WARNING, 1.5" X 5.0"
47 1 1052.00036.00 EMI FILTER, THREE LINE 20A
48 1 1086.00008.00 Cord Strain Relief-UL Models
48 1 1086.00031.00 Cord Strain Relief CE Models
49 4 1073.00007.00 Leg-Flange foot
50 1 B015280BN2 Brew Basket-Plastic
50 1 B001280B1 Brew Basket-stainless steel- *Optional accessory
51 1 1104.00061.01 TANK ASSEMBLY, CBS1151 XXV+ 2 x 3kW/240VAC
51 1 1104.00095.01 TANK ASSEMBLY, CBS1151 XXV+ 5kW/240VAC
51 1 1104.00096.01 TANK ASSEMBLY, CBS1151 XXV+ 2 x 2.3kW/240VAC
51 1 1104.00097.01 TANK ASSEMBLY, CBS1151XXV+ 4kW/240VAC

Go to fetco.com for the latest versions of all information Page 16 P167 November 2017
Parts Diagrams CBS-1152V+
Table of authorities for CBS-1152XV+ models
SKU No. ASSY NO. TANK ASSY WIRING DIAG. CONN. CLAMP
E115251 1101.00339.00 1104.00062.01 1401.00148.00 1086.00008.00
E115252 1101.00339.00 1104.00074.01 1401.00148.00 1086.00008.00
E115261 1101.00339.00 1104.00062.01 1401.00160.00 1086.00031.00
E115262 1101.00339.00 1104.00074.01 1401.00160.00 1086.00031.00
E115280 1101.00339.00 1104.00062.01 1401.00148.00 1086.00008.00
E115290 1101.00339.00 1104.00062.01 1401.00156.00 1086.00008.00
E115291 1101.00339.00 1104.00074.01 1401.00156.00 1086.00008.00
E115292 1101.00339.00 1104.00080.01 1401.00155.00 1086.00008.00
E115294 1101.00339.00 1104.00081.01 1401.00155.00 1086.00008.00
E115296 1101.00339.00 1104.00075.01 1401.00156.00 1086.00008.00

Go to fetco.com for the latest versions of all information Page 17 P167 November 2017
Ref Qt
y
Part Numbe
r
Description Drawin
g
1101.00339.00 CBS-1152 XV+
1 1 1111.00086.00 WELDMENT BODY COMPLETE, CBS-1152 XXV+
2 1 1057.00043.00 SOLENOID VALVE, 5.5L/min, 180 DEG, 24VDC
3 2 1083.00005.00 WASHER, M4 18-8 INTERNAL TOOTH LOCKWASHER
4 2 1082.00010.00 SCREW, M4x10 ZINC-PLATED PAN HD. PHILLIPS MACH.
5 1 1102.00243.00 ADAPTER ASSY, 3/4" BSP x 1/4" NPT x 3/8" TUBE
6 1 1065.00009.00 GROUND LUG CONNECTOR, 14-2 AWG, ALUMINUM
7 5 1083.00011.00 WASHER, #8 SCREW SIZE, INTERNAL TOOTH LOCK
8 19 1084.00006.00 NUT, 8-32 18-8 HEX MACHINE SCREW
9 1 1044.00012.00 LABEL GROUND, CE
10 1 1058.00024.00 SWITCH, POWER, DOUBLE POLE, 16A, 125/250 VAC
11 1 1058.00055.00 USB CONNECTOR
12 8 1081.00006.00 SPACER, 6MM OD x 3.2MM ID x 5MM LG, Z/P
13 1 1052.00001.00 POWER SUPPLY, 90-264VAC/24VDC, 1.8A
14 4 1029.00012.00 SPACER, .25" HEX X 1" LG, FEM #4-40 THREAD
15 1 1112.00268.00 WELDMENT, BRACKET TERMINAL BLOCK, 4 POLE
16 1 1102.00284.00 ASSEMBLY, TERMINAL BRACKET International version SKU E115291
16 1 1052.00023.00 EUROSTRIP HE16 TERMINAL BLOCK, 4 POLE, 63 AMP, 18-8 AWG
17 1 1052.00025.00 PLATE, MARKING #BS1016E
18 2 1082.00082.00 SCREW, PHILLIP HD., 8-32 THREAD
19 2 1102.00223.01 SPRAY HOUSING, LARGE, 24 VDC, STRONGER COIL
20 12 1083.00010.00 WASHER, #10 SCREW W/NEOPRENE-BONDED SEAL
21 2 1102.00113.00 SWITCH, REED, ASSEMBLY
22 4 1029.00006.00 NUT, FINGER, #4-40 NYLON
23 1 1102.00372.00 ASSEMBLY, FRONT PANEL, CBS-1100 TWIN
24 1 1046.00051.00" LABEL, "WARNING, EXTREMELY HOT WATER
25 1 1071.00055.00 FAUCET, HOT WATER, PSC-BR-8, WITH FLAT AND STEM
26 1 1084.00048.00 JAM NUT, 1/2-20 UNF, NICKEL PLATED BRASS
27 2 1025.00021.00 TUBE, 31/32"OD X 5/8"ID X 4 1/4"LG, BREW
28 2 1086.00018.00 HEYCO HOSE CLAMP DIA. .875-1.00
29 2 1086.00017.00 HEYCO HOSE CLAMP DIA .1.031-1.187
30 1 1025.00082.00 TUBE, 5/8"OD X 3/8"ID X 19.00"LG.
31 4 1086.00003.00 UNICLAMP, 15.9 HOSE OD CLAMP
32 1 1025.00058.00 TUBE, 9/16"OD X 5/16"ID X 25.00"LG
33 1 1086.00009.00 CLAMP, 3/4" MAX TUBE OD FLOW CONTROL
34 11 1084.00011.00 NUT, CLIP ON (J-NUT), #6-32, 22-20 GA., BLK-PH FINISH
35 1 1001.00372.00 COVER, TOP, CBS-1152 EXTRACTOR XV+
36 12 1082.00017.00 SCREW, TRUSS HD. PHIL. MACHINE, # 6-32 X 1/2 LG.
37 1 1001.00352.00 COVER, UPPER BASE, CBS-1152 EXTRACTOR XV+
38 1 1402.00053.01 HARNESS, HIGH AMP, CBS-1151-XXV+, UL
38 1 1402.00052.01 HARNESS, HIGH AMP, CBS-1151-XXV+, UL CE Only
38 1 1402.00097.01 HARNESS, LOW AMP, CBS-1151-XXV+, UL
39 1 1402.00097.02 HARNESS ADDITION, LOW AMP, CBS-1152-XXV+, UL
40 1 1112.00470.00 WELDMENT, RIGHT COVER, CBS-1150 XXV+
41 2 1046.00003.00 LABEL, CSD WARNING, 1.5" X 5.0"
42 2 1024.00098.00 VENT TUBE, XTS AND 11XX
43 1 1084.00024.00. NUT, CLIP ON (J-NUT), #6-32, 1050 SPR. STL
44 1 1046.00035.00 LABEL, WARNING "TO REDUCE RISK OF ELECTRIC SHOCK OR FIRE"
45 1 1041.00031.00 LABEL, EXTRACTOR XV+ LOGO
46 1 1052.00036.00 EMI FILTER, 3-LINE, 230/400VAC 2Ph, 2L,N,PE CE (SKUs E115161& E115162 only)
47 1 1086.00008.00 Cord Strain Relief-UL Models
47 1 1086.00031.00 Cord Strain Relief CE Models
48 3 1073.00007.00 Leg-Flange foot
49 1 1104.00062.02 Hot Water Tank 3X3kW/240VAC
49 1 1104.00074.02
Hot Water Tank 3X5kW/240VAC
49 1 1104.00075.02 Hot Water Tank 3X4kW/240VAC
49 1 1104.00080.02 Hot Water Tank 2x3kW/240VAC
49 1 1104.00081.02
Hot Water Tank 2X5kW/240VAC
50 2 B015280BN2 Brew Basket-Plastic
50 2 B001280B1 Brew Basket-stainless steel- *Optional accessory

Go to fetco.com for the latest versions of all information Page 18 P167 November 2017
CBS-1151V+ Tank Assembly
Complete CBS-1151 XV+ HOT WATER TANK ASSY, Part number 1104.00061.00
# Qt
y
PART NO DESCRIPTION
1 1 1114.00087.00 WELDMENT, TANK, CBS-2151XV+
2 4 1024.00050.00 GROMMET, SILICONE, 11.4mm ID
2 4 1024.00051.00 PLUG SILICONE, 11.4mm ID
3 1 1023.00166.00 FITTING, COLD WATER INLET, GROMMET DESIGN
4 2 1023.00168.00 FITTING, HOT WATER, GROMMET DESIGN
5 1 1023.00183.00 FITTING, DILUTION, TBS-2121
6 1 1023.00203.00 FITTING, BREW, GROMMET DESIGN
7 1 1024.00054.00 GROMMET, SILICONE PLUG
8 2 1024.00053.00 LEVEL AND TEMP PROBE GROMMET
9 1 1102.00161.00 PROBE ASSEMBLY, TEMP. AND LLC, 8" LONG
10 1 1112.00019.00 PROBE WELDMENT, WATER LEVEL 2.600" LG
11 1 1023.00171.00 FITTING, SINGLE BARBED ELBOW,
12 2 1107.00037.00 HEATER ASSEMBLY, IMMERSION 2300W/240VAC
12 2 1107.00005.00 HEATER ASSEMBLY, IMMERSION 3000W/240VAC
12 2 1107.00010.00 HEATER ASSEMBLY, IMMERSION 4000W/240VAC
12 2 1107.00032.00 HEATER ASSEMBLY, IMMERSION 5000W/240VAC
13 1 1024.00007.00 O-RING, DASH #344, TANK COVER
14 1 1102.00007.00 TANK COVER ASSEMBLY
15 2 1003.00005.00 BRACKET, ONE SHOT THERMOSTAT
16 2 1053.00003.00 THERMOSTAT, SINGLE SHOT, 240V/40A
17 4 1083.00009.00 WASHER, #6 SCREW , INTL TOOTH LOCKWASHER
18 4 1084.00010.00 NUT, HEX, #6-32, UNDERSIZED, ZINC PLATED
19 2 1003.00140.00 ALUMINUM BRACKET FOR SSR
20 2 1052.00033.00 RELAY, SOLID STATE, 50A/480VAC, W/BUILD IN VARISTOR
21 4 1081.00042.00 STANDOFF, 1/4" HEX
22 1 1022.00068.00 INSULATION, TANK FRONT, CBS-2151
23 1 1022.00069.00 INSULATION, TANK BACK, CBS-2151
24 1 1044.00004.00 LABEL, DANGER, HIGH VOLTAGE

Go to fetco.com for the latest versions of all information Page 19 P167 November 2017
CBS-1152V+ Tank Assembly
Complete CBS-1152 XV+ HOT WATER TANK ASSY Part Number 1104.00062.00
# Qty PART NO DESCRIPTION
1 1 1114.00091.00 WELDMENT, TANK CBS-2152
2 5 1024.00050.00 GROMMET, SILICONE, 11.4mm ID
3 1 1024.00050.00 GROMMET, SHORT, SILICONE, LEVEL AND TEMP PROBE
4 2 1024.00053.00 LEVEL AND TEMP PROBE GROMMET
5 1 1023.00166.00 FITTING, COLD WATER INLET, GROMMET DESIGN
6 1 1102.00161.00 PROBE ASSEMBLY, TEMP. AND LLC, 8" LONG
7 1 1112.00019.00 PROBE WELDMENT, WATER LEVEL 2.600" LG
8 1 1024.00051.00 GROMMET, SILICONE, BLANK
9 1 1023.00183.00 FITTING, DILUTION, TBS-2121
10 2 1023.00171.00 (2X)FITTING, SINGLE BARBED ELBOW
11 1 1024.00007.00 O-RING, DASH #344, TANK COVER
12 1 1102.00007.00 TANK COVER ASSEMBLY
13 3 1107.00005.00 HEATER ASSEMBLY, IMMERSION 3kW/240VAC
13 3 1107.00010.00 HEATER ASSEMBLY, IMMERSION 4kW/240VAC
13 3 1107.00032.00 HEATER ASSEMBLY, IMMERSION 5kW/240VAC
14 2 1023.00203.00 FITTING, BREW, GROMMET DESIGN
15 1 1022.00071.00 INSULATION, TANK BACK, CBS-2152
16 1 1022.00070.00 INSULATION, TANK FRONT, CBS-2152
17 3 1003.00005.00 BRACKET, ONE SHOT THERMOSTAT
18 3 1053.00003.00 THERMOSTAT, SINGLE SHOT, 240V/40A
19 7 1083.00009.00 WASHER, #6 SCREW , INTL TOOTH LOCKWASHER
20 6 1084.00010.00 NUT, HEX, #6-32, UNDERSIZED, ZINC PLATED
21 3 1003.00140.00 ALUMINUM BRACKET FOR SSR
22 3 1052.00033.00 RELAY, SOLID STATE, 50A/480VAC, W/BUILD IN VARISTOR
23 6 1081.00042.00 STANDOFF, 1/4" HEX
24 1 1044.00004.00 LABEL, DANGER, HIGH VOLTAGE

Go to fetco.com for the latest versions of all information Page 20 P167 November 2017
Wiring diagrams
SKU DESCRIPTION: KW Amps Wiring Schematic Heaters
E115251 CBS-1152-XV+, 1 or 3Ph, 2 or 3+G, 3 X 3kW/240VAC, 208-240VAC 7.0 - 9.1 19.4 - 22.4 1401.00086.00 3 X 3 KW
E115252 CBS-1152-XV+, 1 or 3Ph, 2 or 3+G, 3 X 5kW/240VAC, 208-240VAC 11.5 15.1 32.0 - 36.9 1401.00086.00 3 X 5 KW
E115261 CBS-1152-XV+, 3Ph, 3L,N,PE, 3 X 3.0kW/240VAC, 230/400VAC, CE 8.6 12.4 1401.00080.00
E115262 CBS-1152-XV+, 3Ph, 3L,N,PE, 3 X 5.0kW/240VAC, 230/400VAC, CE 1.41 20.4 1401.00080.00
E115271 CBS-1152-XV+, 1or3Ph, 3or4+G, 3 X 3kW/240VAC, 120/208-240VAC
E115280 CBS-1152-XV+, 3Ph, 3+G, 3 X 3.0kW/240VAC, 200VAC, J Int 6.5 18.6 1401.00101.00 3 X 3.0 KW
E115290 CBS-1152-XV+, 3Ph, 4+G, 3 X 3.0kW/240VAC, 220/380-240/415VAC, INTL 9.1 11.8 - 12.9 1401.00112.00 3 X 3.0 KW
E115291 CBS-1152-XV+, 3Ph, 4+G, 3 X 5.0kW/240VAC, 220/380-240/415VAC, INTL 15.1 19.5 - 21.4 1401.00112.00 3 X 5.0 KW
E115292 CBS-1152-XV+, 1Ph, 2+G, 2 X 3.0kW/240VAC, 200-240VAC, INTL 4.6 - 6.1 22.4 - 25.8 1401.00110.00 2 X 3.0 KW
E115294 CBS-1152-XV+, 1Ph, 2+G, 2 X 5.0kW/240VAC, 200-240VAC, INTL 6.9 - 10.0 35.2 - 42.1 1401.00110.00 2 X 5.0 KW
E115296 CBS-1152-XV+, 3Ph, 4+G, 3 X 4.0kW/240VAC, 240/415VAC, INTL 1401.00112.00