FGA Little Moppet LMFT-01 User manual

www.familygamesamerica.com
514.485.1834 | 514.485.2944
email: [e-mail]
Little Moppet™ gardening
accessories will start
imaginations growing!
Made to accommodate
small hands, plant the
seed of fun.
Les accessoires de jardinage
Little Moppet™ pour une
imagination fertile ! Fabriqués
pour s'adapter aux petites mains
et aux pouces verts.
Age / Âge : 4+
Keep youngsters active indoors
and out! Burn up excess
energy, improve balance &
motor skills, strengthen
muscles and enhance
healthy growth.
Ces appareils de con-
ditionnement physique
aident les enfants à brûler
leur trop plein d’énergie,
améliorent l’équilibre et la motricité,
renforcent les muscles et contribuent
à une saine croissance.
Age / Âge : 3+
CHOKING HAZARD: This product contains small parts. •
Dispose of plastic bags safely. • Assemble by a responsible adult.
• Only use the tools specified. • Install and use on a flat, solid
surface. • Inspect the product reqularily for loose parts. • Retain
ASSEMBLY INSTRUCTIONS for future use.
RISQUES D’ÉTOUFFEMENT : Ce produit contient de
petites pièces. • Jeter les sacs en plastique en toute sécurité. • Le
montage doit être fait par des adultes uniquement. • Utiliser les
outils spécifiés. • Installer et utiliser sur une surface plane et solide.
• Inspecter régulièrement pour pièces détachées. • Conservez les
INSTRUCTIONS D'ASSEMBLAGE pour référence ultérieure.
• Not to be used by children under age 3 - Maximum weight 99 lbs.
• Consult with your child’s doctor prior to using.
• Never leave child unattended while on a machine.
• Never allow more than 1 user at a time.
• Child must wear shoes while on a machine.
• N’est pas adapté aux enfants de moins de 3 ans - 99 livres maximum.
• Consultez le médecin de votre enfant avant d'utiliser.
• Ne jamais laisser un enfant sans surveillance sur une machine.
• Ne jamais laisser plus d'une enfant sur la machine.
• L'enfant doit porter des chaussures sur la machine.

LMFT-01
Treadmill
Age / Âge : 3+
MAINTENANCE
1. Ensure that all parts and fittings are included.
2. Remove the plastic from the parts and dispose of them safely.
3. Ensure that shoes are free of stones or sand prior to using.
4. Use a sponge with soapy water to clean. No abrasive or acetone
products.
5. If the Tread Running Board becomes dry, spray dry-spray silicone
oil under the tread.
Shifting Running Belt
If the Running Belt has shifted to the Right, use the Screwdriver (20) to turn
the Left rear roller adjustment bolt 1/4” clockwise and the Right rear roller
adjustment bolt 1/4” counter-clockwise. Run the machine for a minute.
Repeat as necessary until the belt is centered. DO NOT OVER-TIGHTEN as it
could permanently damage the belt.
If shifted to the Left, turn the Right adjustment bolt 1/4” clockwise and the
Left adjustment bolt 1/4” counter-clockwise. Repeat as necessary until the
belt is centered.
If the Running Belt shifts when walked on, turn BOTH rear roller adjustments
1/4” clockwise until it stops shifting.
Figure 5
Rear Roller Adjusting Bolts
20

15
16
2
3
1
7
5
4
Step 4
Step 4 Attach the EVA Mounting Strip with the Mounting Bracket (17) on top
of the Front Handrail (11). Secure through the hole in Bracket (17). Attach the
Monitor (13) onto Bracket (17) as shown.
Battery Installment
To set up the monitor, remove Battery
cover of Monitor (13). Insert 1 “AA” battery
as shown. BATTERY NOT INCLUDED.
Figure 4b
Figure 4a
EVA Mounting Strip
20
11
17
13
13
11
13
PARTS
Parts noted as P (preassembled), have already been installed by the factory.
No. Description QTY
1 Main Frame 1
2 Running Belt (P) 1
3 Tread Running Board (P) 1
4 Front Roller (P) 1
5 Rear Roller (P) 1
6 Frame Cap with Bolts (P) 1
7 Plastic Foot (P) 2
8 Left Leg Tube 1
9 Right Leg Tube 1
10a Right-side Handrail with Foam 1
10b Left-side Handrail with Foam 1
11 Front handrail with Foam 1
12 Leg Tube Caps (P) 2
13 Monitor 1
14 Sensor Wiring (P) 1
15 8 x10 mm Bolts 4
16 4 x10 mm Screws 12
17 Monitor Mounting Bracket 1
18 Plastic Sensor Cable Cap 1
19 Allen Key 1
20 Screwdriver 1
18

Step 2
Slide the Sensor Cable (C-Fig. 2a) to the slot on the Plastic Cap (18). Press
into the hole on the Right Leg Tube (9), as shown. Pull the exposed part of
the Sensor Cable from the top, until it is tight. Connect the Cable (C) and (B)
together with Cap (18) before inserting the Right Handrail (10a) to the Frame
and Leg Tube (9). Connect the Left Handrail (10b) as shown. Tighten with
Screws (16).
Step 3
Connect Sensor Cable (A) with (D) before attaching the Front Handrail (11) to
Handrail (10a +b). Check the alignment of the screw holes, then fasten using
Long Screws (16).
Figure 3
20
Step 1
Attach Left (8) and Right
Leg Tube (9) to Frame (1)
with Bolts (15). Guide the
Sensor Cable (C) through
the hole in Right Leg
Tube (9) as shown.
Figure 1
Figure 1a
19
8
9
15
1
1
15
18
CC
18
11
16
10b
10a
D
A
16
Figure 2a
Figure 2b
Figure 2
C
C
B
B
A
18
18
1
1
9
9
16
16
16
16
16
16
16
16
10b
A
10a
8
1
16
10a
10b
20