Kyosho Caliber 60 User manual

THE FINEST RADIO CONTROL MODELS
R
⵾ຠᡷ⦟ߩߚ߼ޔ๔ߥߊ઀᭽ࠍᄌᦝߔࠆ႐ว߇޽ࠅ߹ߔޕ SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. No. 21865
INSTRUCTION MANUAL
SAFETY PRECAUTIONS
This radio control model is not a toy.
˴ߎߩή✢ᠲ❑ᮨဳߪ⃉ౕߢߪ޽ࠅ߹ߖࠎ㧍
٨㜞ㅦߢ࿁ォߔࠆࡠ࡯࠲࡯߇ઃ޿ߚෂ㒾ᕈߩ޽ࠆ ᯏ󰩟
˴
ߢߔޕ ⚵┙ߡޔ㘧ⴕ႐ᚲޔ㔚ᵄޔὐᬌޔᢛ஻ߪߏ⥄り߇
 ⽿છࠍ߽ߞߡⴕߞߡߊߛߐ޿ޕߎࠇߪ޽ߥߚߩ⽿છߢߔޕ
٨ዊߐ޿ㇱຠ߇ᄙ޿ߩߢޔ⚵┙ߡ૞ᬺߪޔᔅߕᐜఽߩ
˴ᚻ߇ߣߤ߆ߥ޿ᚲߢⴕߞߡߊߛߐ޿ޕ
٨ࡈ࡜ࠗ࠻೨ޔࡈ࡜ࠗ࠻ᓟߪᔅߕޔࡆࠬߩ✭ߺޔฦㇱ
˴ຠߩഠൻߥߤࠍὐᬌߒޔ⇣Ᏹ߇޽ࠇ߫឵࡮ୃℂ࡮
˴⺞ᢛࠍⴕ޿ޔ቟ోࠍ⏕⹺ߒߡ߆ࠄߏ૶↪ߊߛߐ޿ޕ
٨⚐ᱜㇱຠએᄖߩࡄ࡯࠷ࠍ૶↪ߒߥ޿ߢߊߛߐ޿ޔ
˴᡿߿⺞ߩේ࿃ߦߥࠆ߅ߘࠇ߇޽ࠅ߹ߔޕ߹ߚޔ
˴␠ᄖຠࠍ૶↪ߒߡߩ᡿ޔ⎕៊╬ߦߟ޿ߡߪޔ৻ಾ
˴⽿છࠍ⽶޿߹ߖࠎޔߏᛚߊߛߐ޿ޕ
٨⚵┙ߡᓟߦޔ߽߁৻ᐲ⺑᣿ᦠࠍ⷗⋥ߒߡߐ޿ޕ
˴⺑᣿ᦠߪޔ޿ߟߢ߽⷗ࠄࠇࠆࠃ߁ߦᄢಾߦ଻▤ߒߡ
˴ߊߛߐ޿ޕ
٨This is a kind of machine including a rotor which rotates with
high speed and has a possibility to be dangerous. You are
responsible for this model's assembly, safe operation (place
to fly, frequency) check and adjustment of the model.
٨Assemble this kit only in places out of children's reach!
٨Take enough safety precaution before and after operation.
After every flight, inspect screws and nuts for looseness, and
parts for wear. Any damaged parts should be immediately
replaced, repaired or adjusted for safe operation.
٨Use only Kyosho genuine parts for replacement.
Failing to do so will result in accidents or malfunction of the
model. Kyosho do not take responsibilities for the accidents
and crashes if using the parts which are not Kyosho genuine
ones.
٨Always keep this instruction manual ready at hand for quick
reference, even after completing the assembly.
RADIO CONTROLLED ENGINE POWERED HELICOPTER
⚵┙㧛ขᛒ⺑᣿ᦠ
ࠠࡖ࡝ࡃ࡯
⚖⠪ะ
For Advanced
flyers.
© 1999 KYOSHO㧛⑌ήᢿォタⶄ⵾
⚵┙ߡࠆ೨ߦߎߩ⺑᣿ᦠࠍ⦟ߊ߅⺒ߺߦߥࠅలಽߦℂ⸃ߒߡߊߛߐ޿ޕ
Before commencing assembly, please read these instructions thoroughly.

19~20mm
39~41mm
33~36mm
2
ࠠ࠶࠻ߩઁߦߘࠈ߃ࠆ‛㧔㧝㧕REQUIRED FOR OPERATION (1)
2
૶↪ߢ߈ࠆࠨ࡯ࡏࠨࠗ࠭
SUITABLE SERVOS
ࠛࡦࠫࡦ㧛ࡑࡈ࡜࡯
Engine and Muffler
عࠣࡠ࡯Άᢱ
Glow Fuel
Glow Fuel
٨No. 96815 ࡢࡦ࠲࠶࠴ࡊ࡜ࠣࡅ࡯࠲࡯
One-touch Plug Heater
٨No. 1791 ࡉ࡝࠶࠷ࠬ࠲࡯࠲࡯
Blitz Starter
٨No. 71481 ࠪ࡯࡞࠼ࡃ࠶࠹࡝࡯
Sealed Battery
٨No. 39508 Άᢱࡈࠖ࡞࠲࡯
Fuel Filter
No. 94402 ᒝᐲ
Medium Strength
No. 94403 㜞ᒝᐲ
Hard Strength
٨ࡠ࠶ࠢ࠲ࠗ࠻ Loctite
No. 80701 Άᢱࡐࡦࡊ㧔㔚േ8㧕
˴˴˴(WGN2WOR'NGEVTKE8
٨
No. 96506 ࡏ࡯࡞࠺ࡈࠣ࡝ࠬ
˴˴˴$CNN&KHH)TGCUG
٨
No.96627
ࠢࠗ࠶ࠢ࠲ࠗ࠻ࠫࠚ࡞ࡏ࡯ࠗ
˴
Gel Boy
٨
No. 80702 Άᢱࡐࡦࡊ㧔ᚻേ㧕
˴˴˴(WGN2WOR/CPWCN
٨
1ࠛࡦࠫࡦࡋ࡝↪ή✢ᠲ❑ᯏ㧔ࡊࡠࡐ㧕
ߣ㔚ᳰ
Radio for engine-powered R/C helicopters,
and dry batteries
٨ߎߩࠠ࠶࠻ߦߪࠛࡦࠫࡦࡋ࡝↪
˴'/5ࠪࠬ࠹ࡓኻᔕ㧔ࠨ࡯ࡏࠫࡖࠗࡠ㧕ߩ
ࡊࡠࡐ߇ᔅⷐߢߔޕ
٨ࡊࡠࡐߩขᛒ޿ߪޔࡊࡠࡐߦઃዻߩ⺑᣿ᦠ
ࠍෳ⠨ߦߒߡߊߛߐ޿ޕ
عࠛࡦࠫࡦࡋ࡝↪ࡊࡠࡐ
Radio for engine-powered
R/C helicopters
٨This kit requires an EMS system radio for
engine-powered R/C helicopters with 5
servos and 1 gyro.
٨For more information the radio, refer to the
instruction manual supplied with the set.
4ᆎേ↪ౕ
Required for engine starting: 5ធ⌕೷╬ Glues & Lubricants
6ߐࠄߦ↪ᗧߔࠆߣ⦟޿߽ߩ
Useful Additional Equipment
3ࠣࡠ࡯ΆᢱޔΆᢱࡐࡦࡊ
Glow Fuel and Fuel Pump
The illustration of the radio shown here is taken from Futaba instructions.
ᧄ⺑᣿ᦠߩࡊࡠࡐࠗ࡜ࠬ࠻ߪޔ(WVCDCขᛒ⺑᣿ᦠࠃࠅォタߒ߹ߒߚޕ
عࡋ࡝↪ࠢ࡜ࠬࠛࡦࠫࡦ
عࡔࠗࡦࡠ࡯࠲࡯
عࡑࡈ࡜࡯
Muffler
عࡊ࡜ࠣࡅ࡯࠲࡯
Plug Heater
.60 size engine for helicopters
٨Engines for R/C models require glow fuel. Never use gasoline (petrol) or kerosene; both cannot
be used! Also, be very careful when handling glow fuel, as it is highly flammable and explosive!
٨Fuel should contain at least 15% of nitro metane.
عΆᢱࡐࡦࡊ
Fuel Pump
modele
ngine fuel
ࠟ࠰࡝ࡦ߿Ἦᴤߪ
૶↪⑌ᱛ
WARNING: Gasoline
or kerosene cannot
be used!
⼊๔
عࠬ࠲࡯࠲࡯
Starter
عࡀࠫࡠ࠶ࠢ೷
Screw Locking Compound /
Screw Cement / Threadlocker
عࠣ࡝ࠬ
Grease
ع⍍㑆ធ⌕೷
Instant Glue (Super Glue)
عࠬ࠲࡯࠲࡯↪8ࡃ࠶࠹࡝࡯
12V Battery
٨No. Z8020 HP 6mm/౐ⷺ࠷࡯࠙ࠛࠗࠬ࠲࡯࠲࡯ࠪࡖࡈ࠻
HP 6mm Hexagon Reversible Starter Shaft
عࠬ࠲࡯࠲࡯ࠪࡖࡈ࠻
Starter Shaft
عΆᢱࡈࠖ࡞࠲࡯
Fuel Filter
Grease
ࠫࡖࠗࡠ
1
2
3
4
5
6
7
8
9/B
DSC
DUAL
ONVERSION
C
PULSECODE MODULATION
9CHANNEL
RECEIVER
CONNECT
RATEGYRO
ⓨ↪㧔ࡋ࡝↪㧕ߩࡊࡠࡐ࠮࠶࠻ࠍᔅߕ
૶↪ߒߡߊߛߐ޿ޕ㧔ⓨ↪એᄖ૶↪⑌ᱛ㧕
CAUTION: Only use a radio for R/C heli-
copters! (Any other radio is prohibited!)
ᵈᗧ
٨
7
⚵┙ߡߦᔅⷐߥᎿౕ
Tools required
ࠠ࠶࠻ߩઁߦߘࠈ߃ࠆ‛㧔㧞㧕˴REQUIRED FOR OPERATION (2)
عࠞ࠶࠲࡯࠽ࠗࡈ
Sharp Hobby Knife
ع౐ⷺ࡟ࡦ࠴㧔1.5mm, 2mm, 2.5mm, 3mm㧕
Hex Wrench (1.5mm, 2mm, 2.5mm, and 3mm)
ع㧗࠼࡜ࠗࡃ࡯㧔ዊ㧕
Phillips Screw Driver (S)
ع࡜ࠫࠝࡍࡦ࠴
Needle Nose Pliers عࠠ࡝
Awl
ع࠾࠶ࡄ࡯
Wire Cutters
عࡊ࡜ࠣ࡟ࡦ࠴
˴Glow Plug Wrench
ࠬࡍࠪࡖ࡞࠹࡯ࡄ࡯࡝࡯ࡑ࡯
SPECIAL TAPER REAMER No.80311
ⓣടᎿ߇ⷐߢޔ⋥ធOO㨪OO
ߩⓣ޽ߌ߇ߢ߈ࠆᎿౕߢߔޕ
No need to pre-drill!
Drills neat1~15mmholes directly!
૶↪ߔࠆᎿౕߩขᛒ޿ߦߪޔలಽᵈᗧߒߡߊߛߐ޿ޕ
Handle the tools carefully!
/CKP4QVQT$NCFGU
(12V-6.5A)
㐳ߐ  660 mm
ขઃⓣ*QNGUK\G5mm
ෘߐ6JKEMPGUU12 mm
.GPIVJ
ع ࡜࠳࡯ࠨ࡯ࡏ↪ ᑧ㐳
˴ࠦ࡯࠼㧔OO㧕ᧄ
˴Extension Cord for
Rudder Servo (300mm)
٨ᮨဳ↪ࠛࡦࠫࡦߪኾ↪ߩࠣࡠ࡯Άᢱ߇ᔅⷐߢߔޕࠟ࠰࡝ࡦ߿Ἦᴤߪ૶↪ߢ߈߹ߖࠎߩߢᵈᗧߒߡ
ߊߛߐ޿ޕ߹ߚޔࠣࡠ࡯Άᢱߪើ⊒ᕈ߇㜞ߊᒁἫߒ߿ߔ޿ߩߢขᛒ޿ߦߪలಽᵈᗧߒߡߊߛߐ޿ޕ
Άᢱߪޔ࠾࠻ࡠಽ15 % એ߇ㆡߒߡ޿߹ߔޕ

3
ࡊࡠࡐߩḰ஻˴RADIO PREPARATION
٨ࡊࡠࡐࠍߩ㗅⇟ߦߒߚ߇ߞߡ࠮࠶࠻ߒ߹ߔޕ
Set up the radio as explained below.
1
2
3
ฦ⸳ቯ↹㕙ࠍ㐿ߊޕ㧔ㅍାᯏ㧕
࿑ࠍෳ⠨ߦฦ⸳ቯࠍⴕ߁ޕ㧔ㅍାᯏ㧕
4
4
࠻࡝ࡓࠍᄩߦ࠮࠶࠻ߔࠆޕ㧔ㅍାᯏ㧕
5
ࠬࠗ࠶࠴ࠍ౉ࠇࠆޕ㧔ㅍାᯏ㧕
6ࠬࠗ࠶࠴ࠍ౉ࠇࠆޕ㧔ฃାᯏ㧕
7ࠬ࠹ࠖ࠶ࠢࠍേ߆ߒߡࠨ࡯ࡏ߇േ޿ߡ޿ࠆ߆⏕⹺ޕ
ࠬࠗ࠶࠴ࠍಾࠆޕ㧔ฃାᯏ㧕
ㅍାᯏߩࠬ࠹ࠖ࠶ࠢࠍ┙ߦߔࠆޕ㧔ㅍାᯏ㧕
8
ࠬࠗ࠶࠴ࠍಾࠆޕ㧔ㅍାᯏ㧕
ࠕࡦ࠹࠽ࠍ❗߼ࠆޕ㧔ㅍାᯏ㧕
9
10
11
࿑ߦᓥ޿ޔฦࠨ࡯ࡏ╬ࠍฃାᯏߦធ⛯ߔࠆޕ
٨ᆎ߼ࠆᤨ
٨⚳ࠊࠆᤨ
1
2
3
4
Set trims to center. (Transmitter)
5
Switch on the transmitter. (Transmitter)
Open the setting menu. (Transmitter)
Set up the data following the illustration. (Transmitter)
6Switch on the receiver. (Receiver)
7Make sure the servos move according to
your transmitter inputs.
Switch off the receiver. (Receiver)
Set transmitter sticks to neutral. (Transmitter)
8
Switch off the transmitter. (Transmitter)
Retract the antenna. (Transmitter)
9
10
11
Connect servos to the receiver using the illustration above.
٨START
٨FINISH
ㅍାᯏ
Transmitter
٨࡝ࡃ࡯ࠬࠬࠗ࠶࠴ Reverse Switch
JRࡊࡠࡐߩ႐ว
ࠛ࡞ࡠࡦ Aileron
ࠬࡠ࠶࠻࡞ Throttle
ࡁ࡯ࡑ࡞ Normal
࡝ࡃ࡯ࠬ Reverse
CH3
ࠬࡠ࠶࠻࡞ࠨ࡯ࡏ
6JTQVVNG5GTXQ
ࠫࡖࠗࡠ(GY501ߩ႐ว) Gyro(In GY501 case)
R149DPฃାᯏ R149DP Receiver
ฃାᯏࠬࠗ࠶࠴
Receiver Switch
࠾࠶ࠞ࠼㔚ᳰ
Nicd Battery
ల㔚ญ
Terminal to charge
CH6
ࡇ࠶࠴ࠨ࡯ࡏ
Pitch Servo
CH4 ࡜࠳࡯ࠨ࡯ࡏ
Rudder Servo
CH2
ࠛ࡟ࡌ࡯࠲࡯ࠨ࡯ࡏ
'NGXCVQT5GTXQ
CH1
ࠛ࡞ࡠࡦࠨ࡯ࡏ
Aileron Servo
1
2
3
4
5
6
7
8
9/B
DSC
DUAL
ONVERSION
C
PULSE CODE MODULATION
9 CHANNEL
RECEIVER
CONNECT
RATEGYRO
࡜࠳࡯ Rudder
ࠛ࡟ࡌ࡯࠲࡯ Elevator
ࡇ࠶࠴ Pitch
2
3
˴㧔ࡕ࠺࡞ࡔ࠾ࡘ࡯߇㐿ߊ㧕
MDL ࠍㆬᛯ
ㆬᛯ
Select
ㆬᛯ
Select
1
3
4
2
5-2
ㆬᛯ
Select
࠲ࠗࡊߩ⸳ቯߢ ˴˴˴ࠍㆬᛯߔࠆޕ
Select SR3 in Swash Type Menu.
SR3
SR3
Select MDL to open model menu.
5-1 AIL , ELE , PIT ߩ૞േ㊂ޔ૞േᣇะࠍ⸳ቯߔࠆޕ
Select the way and volume of AIL, ELE, PIT movement.
ᢙ୯ߪࠬࡢ࠶ࠪࡘࡊ࡟࡯࠻ߩ૞േ㊂
㧗ޔ࡯ߪࠬࡢ࠶ࠪࡘࡊ࡟࡯࠻ߩ૞േᣇะ
ࡈ࠲ࡃ1024 ZHߩ႐ว
In Futaba 1024ZH case.
EMS ߩ⸳ቯ EMS setting
65 SWASH MIX
3 SERVOS (120¡)
AILE - 65
ELEV - 65
PITCH + 65
ࠛ࡞ࡠࡦ
ࠛ࡟ࡌ࡯࠲࡯
ࡇ࠶࠴
In case of JR radio
㧗࡯indicate a direction of swashplate movement.
Figure indicates the volume of Swashplate movement.

1
⚵┙ߡࠆ೨ߦ⺑᣿ᦠࠍ⦟ߊ⺒ࠎߢޔ߅߅ࠃߘߩ᭴ㅧࠍℂ⸃ߒߡ߆ࠄ⚵┙ߡߦ౉ߞߡߊߛߐ޿ޕ
Read through the manual before you begin, so you will have an overall idea of what to do.
⚵┙ߡ೨ߩᵈᗧ㧔㧝㧕 BEFORE YOU BEGIN (1)
4
ࠠ࠶࠻ߩౝኈࠍ߅⏕߆߼ߊߛߐ޿ޕ৻⦟ޔ⿷߇޽ࠅ߹ߒߚࠄޔ߅⾈޿᳞߼ߩ⽼ᄁᐫߦߏ⋧⺣޿ߚߛߊ߆ޔ
ᒰ␠ޟ࡙࡯ࠩ࡯⋧⺣ቶޠ߹ߢߏㅪ⛊ߊߛߐ޿ޕ
Check all parts. If you find any defective or missing parts, contact your local dealer or our Kyosho Distributor.
2
⺑᣿ᦠߩ⷗߆ߚ
How to read the instruction manual:
3
⺑᣿ᦠߦ૶ࠊࠇߡ޿ࠆࡑ࡯ࠢ
Symbols used throughout the instruction manual, comprise:
4
ࠛࡐࠠࠪធ⌕೷ߢធ⌕ߔࠆޕ
Apply epoxy glue.
⍍㑆ធ⌕೷ߢធ⌕ߔࠆޕ
Apply instant glue (CA glue, super glue).
ࠣ࡝ࠬࠍႣࠆޕ
Apply grease.
ࡀࠫࡠ࠶ࠢ೷ࠍႣࠆޕ
Apply threadlock (screw cement).
㧞࠮࠶࠻⚵┙ߡࠆ㧔଀㧕ޕ
Assemble as many times as
specified (here: twice).
x2
Ꮐฝหߓࠃ߁ߦ⚵┙ߡࠆޕ
Assemble left and right sides
the same way.
ේኸ࿑
True-to-scale diagram.
೎⾼౉ຠ
Must be purchased separately!
઒ᱛ߼ޕ
Tempororarily tighten.
OOߩⓣࠍ޽ߌࠆ㧔଀㧕ޕ
Drill holes with the specified
diameter (here: 2mm).
ᵈᗧߒߡ⚵┙ߡࠆᚲޕ
Pay close attention here!
૶↪ߔࠆⴼ⹣ޕ
Part bags used.
˴˴˴ࠍࠞ࠶࠻ߔࠆޕ
Cut off shaded portion.
2mm
ާ⺑᣿଀Exampleި
⇟ภߩ㗅ߦ⚵┙ߡࠆޕ
Assemble in the specified
order.
9࠹࡯࡞
6CKN HH-2
2
2.6 x 10mm
ࠠࡖ࠶ࡊࡆࠬ
Cap Screw
1
3x3mm
࠮࠶࠻ࡆࠬ
Set Screw
2
2.6mm
࠽ࠗࡠࡦ࠽࠶࠻
3 x 3mm
࠹࡯࡞ࡠ࡯࠲࡯ࠕ࠶࠮ࡦࡉ࡝࡯
Tail Rotor Assembly
2.6 x 10mm
2.6mm
92
ዊ‛ㇱຠߩฬ೨ޔේኸ࿑ޔ૶↪ᢙޕ
Key Number, Part Name, True-to-scale
Diagram, Quantity Used
⺑᣿ᦠౝߢߪᄙߊߩࡑ࡯ࠢ߇૶↪
ߐࠇߡ޿߹ߔޕࡑ࡯ࠢߦᵈᗧߒߡ
⚵┙ߡࠍㅴ߼ߡߊߛߐ޿ޕ
This instruction manual uses seve-
ral symbols. Please note them
during the entire assembly.
ࠠ࠶࠻ౝߩㇱຠߪޔࡆࠬ㘃ࠍ㒰޿ߡࠠ࡯
0Q߇ઃߌࠄࠇߡ޿߹ߔޕࠬࡍࠕࡄ࡯࠷ࠍ
⾼౉ߔࠆᤨߪࠠ࡯0Qࠍෳᾖߒߡߐ޿ޕ
All parts except screws are identified by
key numbers. For purchasing spare parts,
find the key no. of the part needed in the
spare part list and refer to the left column
to look up the corresponding order no.
Nylon Nut

BEFORE YOU BEGIN (2)
5
62ࡆࠬߪޔㇱຠߦࡀࠫࠍಾࠅߥ߇ࠄߒ߼ߟߌࠆࡆࠬߢߔޕߒ߼ߎߺ߇࿕޿႐ว߇
޽ࠅ߹ߔ߇ޔㇱຠ߇⏕ታߦ࿕ቯߐࠇࠆ߹ߢߒ߼ߎࠎߢߊߛߐ޿ޕߚߛߒޔߒ߼ߔ
߉ࠆߣࡀࠫ߇߈߆ߥߊߥࠅ߹ߔߩߢޔㇱຠ߇ᄌᒻߔࠆ߹ߢߒ߼ߥ޿ߢߊߛߐ޿ޕ
Self-tapping (TP) screws cut threads into the parts when being tightened. Excessive force may
permanently damage parts when tightening TP screws. It is recommended to stop tightening when
the part is attached or when some resistance is felt after the threaded portion enters the plastic.
7
ࡆࠬ߇߈߆ߥ޿
The threads are stripped.
ߒ߼ߔ߉
Overtightened.
Correct
Wrong
ࠠ࠶࠻ߦߪޔᒻ߿㐳ߐ߇㆑߁ࡆࠬ߿ዊ‛ㇱຠ߇ᄙߊ౉ߞߡ޿߹ߔޕ⺑᣿ᦠߦߪේኸ࿑߇޽ࠅ߹ߔߩߢ⏕⹺ߒߡ߆ࠄ⚵┙ߡ
ߡߊߛߐ޿ޕ߹ߚޔࡆࠬ㘃ߪᄙ߼ߦ౉ߞߡ޿ࠆ߽ߩ߽޽ࠅ߹ߔߩߢޔ஻ߣߒߡ߅૶޿ߊߛߐ޿ޕ
This kit contains screws and hardware in different metric sizes and shapes. Before using them, check the screws on the true-to-scale diagrams on the
left side in each assembly step. Some screws are extras.
6
٨ࡆࠬߩ⒳㘃 SCREWS
ࡆࠬ Screw
ࠠࡖ࠶ࡊࡆࠬ
Cap Screw
TPࡆࠬ
Self-tapping (TP) Screw
TPࠨ࡜ࡆࠬ
TP F/H Screw
࠮࠶࠻ࡆࠬ
Set Screw
٨ዊ‛ㇱຠߩࠨࠗ࠭଀ OTHER HARDWARE
3x12mm ࡆࠬ
Screw
3mm
12mm
ࠨ࡜ࡆࠬ
Flat Head (F/H) Screw
3mm ࡢ࠶ࠪࡖ࡯࡮࠽࠶࠻
Washer࡮Nut
3mm
5x10mm ࡔ࠲࡞࡮ࡌࠕ࡝ࡦࠣ
Metal Bushing࡮Bearing
5mm
10mm
4mm
E4 㧱࡝ࡦࠣ
E-ring
٨6,000
ࡄ࡯࠰࠽࡞ࡃࡦ࠼ࡕ࠾࠲࡯ߦߟ޿ߡ ABOUT THE "PERSONAL FREQUENCY MONITOR"
ᗲᯏߩ㘧ⴕ೨ߦޔ૶߁ࡃࡦ࠼ߩࠢ࡝ࠬ࠲࡞ࠍ࠮࠶࠻
ߒߡࠬࠗ࠶࠴ࠝࡦ㧍 ห৻ࡃࡦ࠼ߩ㔚ᵄࠍࠠࡖ࠶࠴
ߔࠆߣࡉࠩ࡯㖸ߣLEDߩశߢ⼊๔ޕ
Before operating your helicopter, plug the crystal of your
frequency into the Personal Fre-quency Monitor. As soon
as you switch it on, you'll know for sure through an interfe-
-rence signal and LED lamps whether somebody else is
on your fre-quency or not! PERSONAL
BAND MONITOR
40MHZ
OFF
ON
KYOSHO
CORPORATION
No.80591
JRMSA
77
KYOSHO CORPRATION
No.80591 (40MHz)
No.80592 (72MHz)
ኾ↪ࠢ࡝ࠬ࠲࡞೎ᄁ
Special crystals are
available at Kyosho!
ࠠ࠶࠻ౝߩㇱຠߩߦߪޔ⚵┙󰶄ߺߩㇱຠ߇޽ࠅ߹ߔޕ
ᔨߩߚ߼ࡆࠬ╬ߩࠁࠆߺ߇ή޿߆⏕⹺ߒߡ߆ࠄޔ⚵┙ߡ
ߡߊߛߐ޿ޕ
Inside the kit, you will find assemblies, i.e. sections that are pre-assembled
and hence consist of more than one part. To make sure these assemblies
are safely assembled, check among others their screws for looseness. Only
then, build in the assemblies.
5

8
3x4x4.5mm ࠞ࡜࡯
˴˴˴˴ Collar
1
2࡜࠳㧙ࡈ࡟࡯ࡓ
Ladder Frame
૶↪ߔࠆⴼ⹣ޕ
Part bags used.
12x24x6mm ࡌࠕ࡝ࡦࠣ
˴˴˴˴˴Ball Bearing
2
7x17x5mm ࡌࠕ࡝ࡦࠣ
˴˴˴˴˴Ball Bearing
2
3x10mm ࠠࡖ࠶ࡊࡆࠬ
˴˴˴˴ Cap Screw
8
3x8mm ࠠࡖ࠶ࡊࡆࠬ
˴˴˴Cap Screw
5
3x10mm
3x10mm
3x8mm
CA-1.CA-2
CA-1,CA-2
࡜࠳㧙ࡈ࡟࡯ࡓ
Ladder Frame
ะ߈ߦᵈᗧޕ
Note the direction!
6
ࡀࠫࡠ࠶ࠢ೷ࠍႣࠆޕ
Apply threadlock
(screw cement).
ߎߩ⺑᣿ᦠߪᧄຠߩ᭴ㅧࠍߏℂ⸃޿ߚߛߊߚ߼ߦޔ⚵┙󰶄ߩࠕ࠶࠮ࡦࡉ࡝㧙ㇱಽ߿ࡌࠕ࡝ࡦࠣ╬ߩធ⌕󰶄
ㇱಽ߽⚵┙ߡ޿ߚߛߊࠃ߁ߦ⺑᣿ߒߡ޿߹ߔޕࠝ࡯ࡃ࡯ࡎ࡯࡞ޔㇱຠ឵╬ߩߣ߈ߦෳ⠨ߦߒߡߊߛߐ޿ޕ
In Order to understand full assembly sequence, this instruction manual shows the complete assembly of this model,
even though some elements are supplied pre-built. please refer to it when carrying out maintenance or replacing parts.
707
707
707
708
708
602
603
602
603
604
647
647
647
601
708
610
610
ࡌࠕ࡝ࡦࠣ⚵┙󰶄
Ball Bearing pre-installed
602
708

3
4
࡜࠳㧙ࡈ࡟࡯ࡓ
Ladder Frame
ࠨ࡯ࡏࡊ࡟࡯࠻
Servo Plate
૶↪ߔࠆⴼ⹣ޕ
Part bags used.
3x10mm ࠠࡖ࠶ࡊࡆࠬ
˴˴˴˴ Cap Screw
6
3x6mm ࠠࡖ࠶ࡊࡆࠬ
˴˴˴˴ Cap Screw
5x11x5mm Fࡌࠕ࡝ࡦࠣ
˴Flanged Ball Bearing
10
2
3x10mm
3x10mm
ធ⌕󰶄
glued
3x10mm
3x6mm
3x6mm
4x10mm
4x10mm ࠠࡖ࠶ࡊࡆࠬ
˴˴˴˴ Cap Screw
2
3x10mm ࠠࡖ࠶ࡊࡆࠬ
˴˴˴˴ Cap Screw
4
Ꮐฝหߓࠃ߁ߦ⚵┙ߡࠆޕ
Assemble left and right sides the same way.
઒ᱛ߼ޕ
Temporarily tighten.
605
606
609
607
611
611
608
611
709
709
709
CA-B,CA-1,CA-2
CA-C,CA-1,CA-2
3x14mm
3x10mm
ᄖ஥
Outside
ౝ஥
Inside
608727
Short Body Mount
7
ࡀࠫࡠ࠶ࠢ೷ࠍႣࠆޕ
Apply threadlock
(screw cement).
699
698
3x14mm
⍴޿ᣇ
4
3x14mm ࠮࠶࠻ࡆࠬ
˴˴˴Set Screw

5
6
CA-B
ࡊ࡯࡝࡯
Pulley
CA-B
CA-3
૶↪ߔࠆⴼ⹣ޕ
Part bags used.
10x19x5mm ࡌࠕ࡝ࡦࠣ
˴˴˴˴˴˴˴Ball Bearing
2
10x16x12mm ࡢࡦ࠙ࠚࠗࡌࠕ࡝ࡦࠣ
˴˴˴˴˴˴One Way Bearing
˴˴˴˴˴
1
7x13x1.5mm ࠞ࠙ࡦ࠲࡯ࠡࡗ ࠞ࡜࡯
Counter Gear Collar
˴˴˴˴˴
1
ೞශ߇޽ࠆ߶߁߇
Mark should be this way down
2
3x5mm ࠮࠶࠻ࡆࠬ
˴˴˴˴ Set Screw
710
710
710
711
711
612
616
616
617
614
615
613
ࠣ࡝ࠬࠍႣࠆޕ
Apply grease.
ႣᏓ󰶄˴⵬లߪ0Qࡏ࡯࡞࠺ࡈࠣ࡝ࠬ
˴˴˴˴ࠍᔅߕ૶↪ߔࠆޕ
Be certain to apply 96506 ball diff.grease
ࡌ࡞࠻ࠍ᛬ࠄߥ޿ࠃ߁ߦᵈᗧޕ
Be careful not for being bent.
ࡊ࡯࡝࡯
Pulley
8
ࡀࠫࡠ࠶ࠢ೷ࠍႣࠆޕ
Apply threadlock
(screw cement).
A
A߳
3x5mm
3x5mm

Top

Bottom
ᵈᗧߒߡ⚵┙ߡࠆᚲޕ
Pay close attention here!
⚵┙󰶄
pre-assembled

7
8
CA-B,CA-3
CA-B,CA-4
ࡔࠗࡦࡑࠬ࠻
Main Mast
૶↪ߔࠆⴼ⹣ޕ
Part bags used.
1
3x12mm ࠠࡖ࠶ࡊࡆࠬ
˴˴˴˴ Cap Screw
1
2
12x21x5mm ࡌࠕ࡝ࡦࠣ
˴˴˴˴ Ball Bearing
1
3x24mm ࠠࡖ࠶ࡊࡆࠬ
˴˴˴˴ Cap Screw
1
3mm ࠽ࠗࡠࡦ࠽࠶࠻
˴˴ Nylon Nut
3x24mm
3x12mm
3mm
5x10mm
೎⾼౉ຠ
Must be purchased
separately!
712
ࠢ࡜࠶࠴ࠪࡖࡈ࠻ࡢ࠶ࠪࡖ࡯
Clutch Shaft Washer
721
620
621
619
⇟ภߩ㗅ߦ⚵┙ߡࠆޕ
Assemble in the specified
order.
3
2
1
3
6
5
2
1
712
712
721
625
622
623
ࠢ࡜࠶࠴
Clutch
626
࠙࠶࠼࡜ࡈࠠ࡯
9QQFTWHH-G[
ᵈᗧ˴˴˴ߪㇱࡌࠕ࡝ࡦࠣ
˴˴˴˴˴ߦࡇ࠶࠲࡝วߖࠆޕ
Note: Be sure to install tightly
against upper bearing.
612
612
612
1
5x10mm ࠮࠶࠻ࡆࠬ
˴˴˴˴Set Screw
624
⚵┙󰶄
pre-assembled
⚵┙󰶄
pre-assembled
9
ࡀࠫࡠ࠶ࠢ೷ࠍႣࠆޕ
Apply threadlock
(screw cement).
ࠛࡦࠫࡦ
Engine.
ࠛࡦࠫࡦઃዻࡢ࠶ࠪࡖ࡯
Supplied with the engine.
ࠛࡦࠫࡦઃዻ
Supplied with the engine.

CA-B,CA-4
CA-4
૶↪ߔࠆⴼ⹣ޕ
Part bags used.
9
10
4
4x10mm ࠠࡖ࠶ࡊࡆࠬ
˴˴˴˴ Cap Screw
4
4x15mm ࠠࡖ࠶ࡊࡆࠬ
˴˴˴˴ Cap Screw
4x15mm
Ꮐฝหߓࠃ߁ߦ⚵┙ߡࠆޕ
Assemble left and right sides the same way.
ࠛࡦࠫࡦ
'PIKPG+PUVCNNCVKQP
627
4x10mm
628
ࠛࡦࠫࡦ
'PIKPG+PUVCNNCVKQP
10
ࡀࠫࡠ࠶ࠢ೷ࠍႣࠆޕ
Apply threadlock
(screw cement).
ߔߴߡߩࡆࠬ
Every Screw