Fiberme FAG410X User manual

FIBERME Communications LLC.
Configuring FAG410X with Elastix

P a g e 1
Table of Contents
OVERVIEW..................................................................................................................... 3
CONNECT Elastix TO FAG410X USING PEER SIP TRUNK........................................ 4
Create IVR On Elastix................................................................................................................................................4
Create Peer SIP TRUNK On Elastix.............................................................................................................5
Configure Outbound Rule On Elastix.......................................................................................................................5
Configure Inbound Rule On Elastix..........................................................................................................................6
Connect FAG410X with Elastix................................................................................................................................7
Configure FXO Port on FAG410X.................................................................................................................8
Create Port Group on FAG410X...................................................................................................................9
REGISTER FAG410X ON Elastix AS AN EXTENSION.....................................................10
Create SIP Extension on Elastix............................................................................................................................ 10
Configure FAG410X SIP Account as a Registered Extension on Elastix........................................................ 10
FAG410X CALL Routing ............................................................................................. 12
Configure IP to Tel on FAG410X .......................................................................................................................... 12
Configure TEL to IP on FAG410X...............................................................................................................13

P a g e 2
Table of Figures
Figure 1: Create IVR on Elastix...................................................................................................................................4
Figure 2: Create Peer SIP Trunk on Elastix ..............................................................................................................5
Figure 3: Configure Outbound Rule on Elastix .........................................................................................................6
Figure 4: Configure Inbound Rule on Elastix ............................................................................................................7
Figure 5: Connect FAG410X with Elastix: Registrar IP Address ...........................................................................7
Figure 6: Connect FAG410X with Elastix: Register Gateway ................................................................................8
Figure 7: Configure FXO Port on FAG410X: Modify Port.......................................................................................8
Figure 8: Configure FXO Port on FAG410X: Port Configurations .........................................................................8
Figure 9: Create Port Group on FAG410X: Add New..............................................................................................9
Figure 10: Create Port Group on FAG410X: Group Configurations......................................................................9
Figure 11: Create SIP Extension on Elastix..............................................................................................................10
Figure 12: FAG410X SIP Account Settings ..............................................................................................................10
Figure 13: FAG410X Registrar IP Address...............................................................................................................11
Figure 14: Elastix - SIP Extension Status..................................................................................................................11
Figure 15: FAG410X –IP to TEL................................................................................................................................12
Figure 16: IP to TEL Settings......................................................................................................................................12
Figure 17: FAG410X –TEL to IP................................................................................................................................13
Figure 18: TEL to IP Settings......................................................................................................................................13

P a g e 3
OVERVIEW
This document describes basic configuration to interconnect Elastix and FAG410X. In this document, we
are using FAG4108 as an example. The following methodology can be used for the FAG4104 as well. This
is typically applied to the scenario where users would like to add a FAG410X not only as a remote extension
but also as an external PSTN trunk.
There are two ways to set up the Elastix IP PBX with the FAG410X.
• Method 1: Configure FAG410X as a SIP Peer Trunk.
• Method 2: Register FAG410X on Elastix directly as an extension.

P a g e 4
CONNECT Elastix TO FAG410X USING PEER SIP TRUNK
Create IVR On Elastix
On the Elastix web GUI, create an IVR extension under PBX->PBX Configuration->IVR.
In IVR settings, if "Direct Dial" is enabled, the calls dialing into the Elastix IVR will be able
to reach the
internal extensions registered to Elastix . Also, you can assign the "IVR Entries" to different destinations.
Figure 1: Create IVR on Elastix

P a g e 5
Create Peer SIP TRUNK On Elastix
On the Elastix web GUI, create a peer SIP trunk under PBX->PBX Configuration->Trunks. In this example, the
FAG4108 IP address is 192.168.99.239.
Figure 2: Create Peer SIP Trunk on Elastix
Configure Outbound Rule on Elastix
On Elastix web GUI, go to PBX->PBX Configuration->Outbound Routes to create a new outbound rule. This
would allow the extension on Elastix to reach numbers in PSTN network via the peer SIP trunk we just configured.

P a g e 6
Figure 3: Configure Outbound Rule on Elastix
In this example prefix "9", 9 is the first dialing digit and it will be stripped off when the callgoes out.
Configure Inbound Rule on Elastix
On Elastix web GUI, go to PBX->PBX Configuration->Inbound Routes to create a new inbound rule. In
this example, we set the DID Number as 20000, which will be used in the FAG410X call forward setting.

P a g e 7
Figure 4: Configure Inbound Rule on Elastix
The default destination is configured to IVR. Ensure to select the proper IVR.
Connect FAG410X with Elastix
1. On the FAG410X web GUI, go to the VoIP->SIP page and enterthe IP address of the Elastix that you
are peering with.
Figure 5: Connect FAG410X with Elastix: Registrar IP Address
2. Please make sure the Register Gateway option under VoIP-> SIP is set to No. In the following
example, Elastix Server has IP address 192.168.99.19.

P a g e 8
Figure 6: Connect FAG410X with Elastix: Register Gateway
Configure FXO Port on FAG410X
1. Connect the PSTN line to the FAG410X FXO port.
2. On the FAG410X web GUI, go to the Port->FXO page and press Modify on the FXO port you will
use.
Figure 7: Configure FXO Port on FAG410X: Modify Port
3. Enter the SIP Account Number 20000 to be matched with the DID number we configured in Elastix
Inbound Route.
Figure 8: Configure FXO Port on FAG410X: Port Configurations

P a g e 9
Create Port Group on FAG410X
1. On the FAG410X web GUI, go to the Port->Port Group page and press “Add New”.
Figure 9: Create Port Group on FAG410X: Add New
2. Select the FXO port you will use.
Figure 10: Create Port Group on FAG410X: Group Configurations

P a g e 10
REGISTER FAG410X ON Elastix AS AN EXTENSION
Create SIP Extension on Elastix
To manually create new SIP user, go to Elastix web GUI PBX->PBX Configuration->Extensions. Click
on"Add" and a new dialog window will show for users to fill in the extension information.
Figure 11: Create SIP Extension on Elastix
Configure FAG410X SIP Account as a Registered Extension on Elastix
Under FAG410X web GUI->VoIP->SIP, please set Register Gateway to Yes, then enter SIP Extension
information created earlier in Elastix. In this example, extension 1002 is used in order to register FAG410X
as an extension user on Elastix.
Figure 12: FAG410X SIP Account Settings

P a g e 11
Under FAG410X web GUI, VoIP->SIP, please fill in Elastix information as explained in method 1.
Figure 13: FAG410X Registrar IP Address
We can check Elastix SIP Extension Status to see if FAG410X has been successfully registered as an
extension device. go to PBX->Tools->Asterisk-Cli, In Command write “sip show peers” and press
Execute. “OK” under Status means that the extension is registered successfully as below screenshot.
Figure 14: Elastix - SIP Extension Status
Now FAG410X is registeredat Elastix as an extension device. Please refer to method 1 in the previous
section to configure FXO Port settings on FAG410X.

P a g e 12
FAG410X CALL Routing
Configure IP to Tel on FAG410X
1. On the FAG410X web GUI, go to the Route-> IP→TEL page, Press “Add New”.
Figure 15: FAG410X –IP to TEL
2. Enter the Elastix Server IP address in “Source IP”and select the Port Group you will use from “Call
Destination”.
Figure 16: IP to TEL Settings

P a g e 13
Configure TEL to IP on FAG410X
1. On the FAG410X web GUI, go to the Route-> TEL→IP page, Press “Add New”.
Figure 17: FAG410X –TEL to IP
2. Select the Port Group you will use from “Source Port Group” and enter the Elastix Server IP address
in “Destination Address”.
Figure 18: TEL to IP Settings