Fieldmann FDV 201205-E User manual

FDV 201205-E

2
FDV 201205-E
English ................................................................................................................................................................................6–16
Čeština............................................................................................................................................................................ 17–28
Slovenčina.................................................................................................................................................................... 29–40
Magyarul....................................................................................................................................................................... 41–52
Polski ................................................................................................................................................................................ 53–64

3

4
FDV 201205-E

EN
IMPACT DRILL 1 200 W OPERATING INSTRUCTIONS
Contents 5
Impact Drill 1 200 W
INSTRUCTION MANUAL
Thank you for your purchase of the impact drill. For your personal safety, read and
understand the Instruction Manual before using. Keep the Instruction Manual in a safe
place for future reference.
CONTENTS
1. GENERAL SAFETY INSTRUCTIONS..........................................................................................................................6
2. SYMBOLS.........................................................................................................................................................................10
3. SAFETY INSTRUCTIONS.............................................................................................................................................. 11
5. TECHNICAL SPECIFICATIONS.................................................................................................................................13
6. TROUBLESHOOTING...................................................................................................................................................14
7. DISPOSAL ........................................................................................................................................................................15

EN 6General safety instructions
FDV 201205-E
1. GENERAL SAFETY INSTRUCTIONS
WARNING! Carefully read the instruction manual before use.
Important safety warnings
Unpack the product carefully and be sure not to throw away any part of the package before having found all
components of the product.
Keep the product in a dry place out of reach of children.
Read all cautions and instructions. The failure to adhere to warning cautions and instructions may result in
an accident, fire and/or a serious injury.
Packaging
The product is placed in a package preventing damage during transport. This package is a raw material therefore
it can be handed-over for recycling.
Instructions for use
Before beginning to work with the machine, read the following safety rules and instructions for use. Familiarize
with operating elements and the proper use of the device. Keep the manual in a safe place for future reference.
We recommend keeping the original package including the inner packaging materials, cash voucher and guar-
antee card for a period of warranty at minimum.
For a case of transportation, pack the machine into the original box from the manufacturer, thus ensuring a maxi-
mum protection of the product during a possible transport (e.g. moving or sending into a service station).
Note: If you hand the machine over to next persons, hand it over together with the manual.
Adherence to the attached instructions for use is a precondition for the proper use of the machine. The
operation manual includes also instructions for operation, maintenance and repairs.
The manufacturer does not take any responsibility for accidents or damages resulting
from the failure to adhere to this manual.
Carefully read, remember and keep these safety instructions
WARNING! In the use of electric machines and power tools, it is necessary to respect and follow the
following safety instructions for the reasons of protection against electric shock, personal injury and danger
of fire. The term “power tool” in the instructions below refers both to mains-operated (corded) power tool or
battery-operated (cordless) power tool.
Save all warnings and instructions for future reference.

EN
IMPACT DRILL 1 200 W OPERATING INSTRUCTIONS
General safety instructions 7
Workplace
Keep the work area clean and well lit. Cluttered or dark areas in the workplace invite accidents. Store power
tools that you don’t currently use.
Do not operate power tools in environments with danger of occurrence of a fire or explosion, such as in the
presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes.
Keep unauthorised persons, especially children, away from the work area while operating a power tool!
Distractions can cause you to lose control over the performed activity. In no event leave your power tool
unattended. Keep the equipment away from animals.
Electrical Safety
Power tool plugs must match the mains socket outlet. Never modify the plug in any way.
Do not use any adapter plugs with earthed (grounded) power tools. Undamaged plugs and matching outlets
will reduce risk of electric shock. Damaged or fouled supply cables increase the risk of electric shock. If
the power cord is damaged, it must be replaced by a new power cord which is available at the authorised
service centre or the importer.
Avoid body contact with earthed or grounded surfaces such as pipes, radiators, cooking ranges and
refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
Do not expose power tools to rain or wet conditions. Never touch the power tool with wet hands. Never wash
the power tool under running water or immerse it in water.
Never use the supply cable for other than intended purposes. Never use the cord for carrying or pulling the
power tool. Never unplug the plug from the outlet by pulling the cable. Keep electric cables away from sharp
or hot objects to prevent mechanical damage.
The power tool was designed to be powered solely by alternating electric current. Always check if the electric
voltage matches the information specified in the type label of the power tool.
Never use power tool with damaged electric cable or plug or which has been dropped or is in any way
damaged.
If an extension cord is used, always check whether its technical parameters match the information specified
in the type label of the power tool. When operating a power tool outdoors, use an extension cord suitable for
outdoor use. If extension drums are used, these must be rolled out to prevent overheating of the cord.
If a power tool is operated in a damp location or outdoors, its operation is only permitted if connected to an
electric circuit protected by a residual current device <30 mA. Use of residual current device (RCD) reduces
the risk of electric shock.
Hold the power tool by insulated gripping surfaces only as the cutting or drilling tool may contact hidden
wiring or its own power cord during operation.
Personal Safety
Be careful, stay alert and watch what you are doing when operating a power tool.
Concentrate on your work. Do not use a power tool while you are tired or under the influence of drugs,
alcohol or medication.
A moment of inattention while operating power tools may result in serious personal injury. Do not eat, drink
and smoke while operating a power tool.

EN 8General safety instructions
FDV 201205-E
Use personal protective equipment. Always wear eye protection. Use protective equipment corresponding to
the type of work you are doing. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or
hearing protection used in accordance with the working conditions will reduce the risk of personal injury.
Prevent unintentional starting. Do not carry the power tool while it is energised or with your finger on the
switch or trigger. Ensure the switch or trigger is in the “off” position before connecting to power source.
Carrying power tools with your finger on the switch or energising power tools that have the switch on may
result in serious injuries.
Remove any adjusting key or wrench before turning the power tool on. An adjusting wrench or a key left
attached to a rotating part of the power tool may result in personal injury.
Keep proper footing and balance at all times. Do not overreach. Never overestimate your own capabilities.
Never use power tools while you are tired.
Dress properly. Wear work clothes. Do not wear loose clothing or jewellery. Keep your hair, clothing, gloves
and other part of your body away from moving or hot parts of the power tool.
Connect the equipment to dust exhaustion. If the tools are provided for the connection of dust collection or
exhaustion devices, ensure these are properly connected and used. Use of such devices can reduce dust-
related hazards.
Fix the work-piece tightly. Use a cabinet clamp or a cramp to fix the work-piece you are about to machine.
Never use power tools if you are under the influence of alcohol, drugs, medication or other narcotic or
addictive substances.
This equipment is not intended for use by persons (including children) with limited physical, sensual or
mental capacities or lack of experience or knowledge unless they are supervised or instructed about the use
of the equipment by a person responsible for their safety. Children must be supervised to make sure they are
not playing with the equipment.
Power Tool Use and Maintenance
Always disconnect the power tool from the mains in case of any problem during the work, before cleaning
the power tool or its maintenance, during each transportation and after the completion of the work! Never
operate a power tool if it is damaged in any way.
Immediately stop working if the power tool generates abnormal noise or smell.
Do not overload the power tool. The power tool will operate better and safer if it is used at the rate for which it
was designed. Use correct power tool which is intended for the given activity.
The correct power tool will do the job it was designed for better and safer.
Do not use the power tool if it cannot be safely turned on and off using the control switch.
Use of such power tool is dangerous. Defective switches must be repaired by a certified service provider.
Disconnect the tool from the power source before making any adjustments, changing accessories or
maintenance. Such preventive safety measure prevents the risk of starting the power tool accidentally.

EN
IMPACT DRILL 1 200 W OPERATING INSTRUCTIONS
General safety instructions 9
Store idle power tools out of the reach of children and unauthorised persons. Power tools can be dangerous
in the hands of untrained users. Store the power tools in a dry and safe place.
Keep the power tool in good condition. Check the adjustment of moving parts and their mobility. Check for
any damage to the protective guards or other parts which could affect safe operation of the power tool. If
damaged, have the power tool properly repaired before further use. Many accidents are caused by poorly
maintained power tools.
Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges facilitate
work, reduce the risk of injury and are easier to control. Use of accessories other than those specified in the
instructions for use could result in damage to the power tool and cause injuries.
Use the power tool, accessories and tool bits etc. in accordance with these instructions and in the manner
intended for the particular type of power tool taking into account the working conditions and the work to be
performed. Use of the power tool for purposes other than those the power tool was intended for could result
in hazardous situations.
Service
Do not replace parts of the power tool, do not make any repairs or interfere in any way with the construction
of the power tool. Have your power tool repaired by qualified repair persons.
Any repair or modification of the product without our company’s authorisation is impermissible (it could
cause injury or damage to the user).
Always have your power tool repaired in a certified service centre. Use only original or recommended
replacement parts. This will ensure that your safety and the safety of your power tool is maintained.

EN 10 Symbols
FDV 201205-E
2. SYMBOLS
The product complies with the applicable
standards and regulations.
Read the Instruction Manual attentively
prior to use.
Double-insulated.
Use adequate eye protective equipment.
Use ears protective equipment.

EN
IMPACT DRILL 1 200 W OPERATING INSTRUCTIONS
Safety instructions 11
3. SAFETY INSTRUCTIONS
Before drilling into walls make sure that you are not breaking into an electricity, gas or water supply line. Use
a suitable detector.
Always unplug the drill before changing a drill or bit.
The chuck key should always be stored in the key holder.
To avoid injuries, securely attach the work piece with a vice or clamp.
When drilling or driving a screw: Do not allow the motor to stall under the load.
In the event of an electrical or mechanical malfunction, immediately switch the drill off and disconnect the
plug.
WARNING! While impact drilling, wear suitable ear protective equipment. Exposure to the excess noise
levels can cause hearing loss.
WARNING! Use auxiliary handles supplied with the tool. Loss of control can cause a serious personal
injury.
4.OPERATION
Intended Use
The impact drill is intended for impact drilling in brick, concrete and stone as well as for drilling in wood, metal
and plastic.
Machines with electronic control and right/left rotation are also suitable for screwdriving and thread-cutting.
Before first Use
Remove the impact drill from the packaging. Keep packaging material out of reach of small children. There is risk
of suffocation!
Important: Before any work on the machine itself, pull the mains plug!
Assembling the Auxiliary Handle and Depth Limiter
1. Assemble the auxiliary handle (6) either on the left or on the right side of the drill spindle, depending on
whether you are left or right handed, or to suit the drilling requirements accordingly. Put the auxiliary handle
on the drill spindle.
2. Fasten the auxiliary handle by turning the handgrip clockwise.
3. At any time you can turn the handgrip of the auxiliary handle counter clockwise to change the angle/the
position of the auxiliary handle.
4. If required, you can insert the depth limiter (3) into the corresponding retainer (2) directly above the handgrip.
Inserting the Tool Bit
1. The impact drill is fitted with a keyed drill chuck (1). Insert the desired tool bit and tighten it manually. Then
use the provided drill chuck key (13) to fasten the bit firmly by tightening the chuck evenly at the position of
each of the holes in the jaws of the chuck.

EN 12 Operation
FDV 201205-E
2. Always use a bit holder when working with screwdriver bits.
3. Only use sharpened High Strength Steel (HSS) drill bits for drilling in metal. Appropriate drill bits are available
though the Westfalia tool bit program.
Switching ON/OFF
1. To switch on the impact drill, press the ON/OFF trigger (10).
Release the trigger to switch it off.
2. The ON/OFF trigger can be locked in the pushed (ON) position by pressing the lock-on button (5). The lock-
on button automatically releases when the ON/OFF trigger is pressed again.
Speed Adjustment Wheel
Depending on the pressure applied on the ON/OFF trigger, the impact drill operates at a variable rotation speed
from 0 to 2800 revolutions per minute (up to 1000 revolutions per minute in the first gear). Light trigger pressure
results in a low rotation speed and smooth controlled starting of the drill.
The required rotation speed for drilling depends on the material being processed. It is best selected by a practical
test. Always use a speed which is high enough to prevent the machine from stopping due to overload. The maxi-
mum speed can be adjusted with the speed adjustment wheel (9).
Changing the Rotating Direction
The switch for clockwise/counter clockwise operation (8) may only be operated when the motor is at a complete
standstill. When the ON/OFF trigger (10) is depressed, the rotational direction switch (8) is blocked.
Clockwise rotation: for drilling and fastening screws
Counter clockwise rotation: for removing screws
Drilling/Impact Drilling
The drilling/impact drilling selector (4) may only be operated when the motor is at a complete standstill.
This selector is located on the top of the impact drill.
For impact-drilling push the switch towards the hammer icon.
For drilling push the switch towards the drill icon.
Selecting the Gear
The gear selection knob (7) is located at the bottom side of the impact drill. The gear selection knob may only be
operated when the motor is at a complete standstill.
Turn the gear selection knob so that the “1” points to the arrow icon. The impact drill operates in the first
gear with a max. revolution speed of 1100 min-1 and with a max. impact rate of 17600 min-1 when impact
drilling.
Turn the gear selection knob so that the “2” points to the arrow icon. The impact drill operates in the second
gear with a max. revolution speed of 3000 min-1 and with a max. impact rate of 48000 min-1 when impact
drilling.

EN
IMPACT DRILL 1 200 W OPERATING INSTRUCTIONS
Technical specifications 13
Maintenance, Cleaning and Storing
Always unplug the impact drill before maintaining it.
Before each use ensure that the ventilation slots are open and clean.
Never clean the impact drill with water. Use a soft cloth to clean the housing. Do not use aggressive
chemicals or solvents to clean the machine as these may damage the surfaces.
If the machine works powerlessly and sparking occurs at the brushes, it may be a sign that the carbon
brushes are worn and have to be replaced. Only have the carbon brushes replaced by a professional or
return the unit to the Westfalia customer service department. Do not open the housing. Do not try to repair it
yourself.
If the keyed drill chuck became damaged, do not try to repair it yourself. Have it replaced by a professional
only or contact the Westfalia customer service.
Store the impact drill indoors in a dry place that is protected from dust, dirt and extreme temperatures.
Store the device out of reach of children.
5. TECHNICAL SPECIFICATIONS
Rated Voltage 230 V~50 Hz
Rated Power 1200 W
No Load Speed1st Gear 0 – 1100 min-1
No Load Speed2nd Gear 0 – 3000 min-1
Impact Rate1st Gear 0 – 17600 min-1
Impact Rate2nd Gear 0 – 48000 min-1
Power Cord Length 3 m
Drill Chuck 3 – 13 mm
Drilling Capacity in Concrete 22 mm
Drilling Capacity in Wood 30 mm
Drilling Capacity in Metal 16 mm
Weight approx. 2,75 kg
Protection Class II
Degree of Protection IP20

EN 14 Troubleshooting
FDV 201205-E
6. TROUBLESHOOTING
Suspected malfunctions are often due to causes the user can fix themselves. Therefore
check the product using this section .In most cases the problem can be solved quickly.
WARNING!
Only perform the steps described within these instructions! All further inspection,
maintenance and repair work must be performed by an authorized service centre or a
similarly qualified specialist if you cannot solve the problem yourself!
Problem Possible Cause Solution
1. Product does not start 1.1 Not connected to power
supply
1.2 Power cord or plug is
defective
1.3 Other electrical defect to the
product
1.1 Connect to power supply
1.2 Check by a specialist
electrician
1.3 Check by a specialist
electrician
2. Product does not reach full
power
2.1 Extension cord is not suitable
for operation with this product
2.2 Power source (e.g. generator)
has too low voltage
2.3 Air vents are blocked
2.1 Use a proper extension cord
2.2 Connect to another power
source
3. Unsatisfactory result 3.1 Drill is dull/damaged
3.2 Drill bit is not suitable for work
piece material
3.1 Replace with new one
3.2 Use proper Drill
4. Excessive vibration or noise 4.1 Drill bit is dull/damaged 4.1 Replace with a new one

EN
IMPACT DRILL 1 200 W OPERATING INSTRUCTIONS
Disposal 15
7. DISPOSAL
INSTRUCTIONS AND INFORMATION ON DISPOSAL OF USED PACKAGING.
Put any used package material to the place determined by the municipality for waste disposal.
DISPOSAL OF USED ELECTRIC AND ELECTRONIC EQUIPMENT
This symbol on products or accompanying documents means that used electric or
electronic products must not be put to ordinary municipal waste. Hand over such products
to determined collection points for proper disposal, restoration and recycling. Alternatively,
in some countries of the European Union or other European countries you can return your
products to your local dealer when you buy an equivalent new product. By dutiful disposal of
this product you can preserve precious natural resources and you help prevent any potential
adverse effects on the environment and human health which could be the results of wrong
waste disposal. Ask your local authority or the nearest collection point for additional details.
In case of improper disposal of this waste kind penalties can be imposed in accordance with
national regulations.
For companies in the European Union countries
Should you want to dispose of electric and electronic devices, ask your dealer or vendor for
necessary information.
Disposal in other countries outside the European Union
Should you want to dispose of this product, ask your local authorities or your dealer for
necessary information about disposal method.
This product fulfils all basic requirements of the EU directives that apply to it.
Text, design and technical specifications can change without prior notice and we reserve the right for their
change.

EN 16
FDV 201205-E