Fiilex P100 Series User manual

User Manual
FLXP100
P100

1
General Notes
• The P100 Series has been designed for professional studio and location applications and may only
be operated by qualified persons.
• Please read the following operating instructions very carefully before using this fixture.
• For your own safety, please follow all safety instructions and warnings.
• Keep these operating instructions for future reference.
• For further information, contact Fiilex ([email protected]) or your retailer.
Basic Operation (refer to Parts Diagram on following page)
• Mounting the P100
The P100 can be mounted onto a cold/hot shoe through its Cold Shoe w/ Mini Ball Head (10).
• Charging
There are two options for charging the P100. The first option uses AC power to charge the
battery while simultaneously running the light. The second option charges the battery
separately.
Option1 : Insert the Power Charger Connector (15) into the Power Charger Input Jack (13). on
the P100 Brick Light. Plug the Power Charger into a standard AC wall outlet to
charge.
Option2 : Remove Battery (11) from the P100 Brick Light. Insert the Power Charger
Connector (15) into the DC Plug Converter (17) into the Power Charger Input
Jack (13) on the Battery (11). Plug the Power Charger into a standard AC wall outlet.
When charging the Charge State Light (16) on the Power Charger turns red. The
Charge State Light (P) turns green when the battery is fully charged.
Parts Indicator Light
Power
Charger
Battery
Description
Battery is charging
Battery < 20%
Battery 20% - 50%
Battery 50% - 100%
Battery is fully charged
*Battery Indicator Light (14) is an estimated measure, the color status may fluctuate from time to time to time
depending on the intensity settling of the P100.

Parts Diagram
Compatible Accessories
2
Turning the light on
Slide On/Off Switch
(3) to turn on P100.
Mounting to Camera
Mount the P100 to
the cold/hot shoe of
your camera via Cold
Shoe w/ Mini Ball
Head (10).
Mounting to Female
Mount
Insert 1/4” - 20 Male
Thread (9) into 1/4” -
20 Female Accessory
Mount (8).
Inserting Battery
Slide the Battery (11)
into P100, or plug
Power Charger
Connector (15) into
DC power input jack.
Light Adjustment
Adjust intensity with
Intensity Knob (5).
Adjust the color
temperature with
CCT Tuning Knob (4).
1. Air Vents
2. Beam Shaper
3. On/Off Switch
4. CCT Tuning Knob (3000-5600K)
5. Intensity Knob
6. Battery Lock
7. DC Power Input Jack
8. 1/4” - 20 Female Accessory Mount
9. 1/4” - 20 Male Thread
10. Cold Shoe w/ Mini Ball Head
11. Battery
12. Battery Pin
13. Power Charger Input Jack
14. Battery Indicator Light
15. Power Charger Connector
16. Charge State Light
17. Plug Jack Converter
11
9
10 3
4
5
8
Half Yoke D-tap Cable Dome DiffuserFresnel LensP100 Accessory Mount
1
2
3
4
5
6
7
89
10
12
13
14
15
16
17
11
Magnetic Gel Holder

3
0.59 lbs / 0.27 kg
DiCon Dense Matrix LED
Fanless Cooling System
3000K-5600K Continuous System
12W Max
12W AC/DC Power Adapter
AC Power: 100-240VAC. 50-60Hz
DC Power: 12.6VDC, 1A, 12W max.
32-104°F / 0-40°C
50° (26° w/ 2” Fresnel Lens)
Cold Shoe w/ Mini Ball Head
42,000 hours
CE, UL, FCC
Weight: Fixture
Light Source
Thermal Design
CCT Range
Power Consumption
Power Connection
Input Voltage
Operating Temperature
Beam Angle
Mounting
LED Lifetime
Certifications
Specifications
Note
• P100 is powered by a rechargeable Li-ion battery. Use only Fiilex approved batteries and
chargers.
• You must fully charge the battery for the first time. A discharged battery recharges fully in
approximately 3 hours.
• Battery only charges through Power Charger Input Jack (13) on battery.
• For connection to an electrical supply not located in the U.S., you must use an adapter of the
proper configuration for the power outlet. Use of the wrong adapter and/or power configuration
could result in damage to the P100 and void your warranty.
• Stop using if it expands or the temperature is over 40°C (104°F) or under 0°C (32°F)

4
Warranty
Unless otherwise stated, your product is covered by a one year parts and labor limited warranty.
Fiilex guarantees, to the original buyer, that this product is to be free of defects in both workman-
ship and material for a period of one year from the date of shipment. This warranty extends to all
products which have proved defective through normal use but excludes products that have been
disassembled, modified or misused by the buyer or any other person. This warranty is in lieu of all
other warranties, and disclaims all warranties expressed or implied, including any warranty of mer-
chantability, fitness for a particular purpose, or arising from the course of dealing between the
parties or usage of trade.
Returning an Item Under Warranty for Repair
It is necessary to obtain a Return Authorization Number (RA#) from your dealer/ point of purchase
BEFORE any units are returned for repair. Fiilex will make the final determination as to whether or
not the unit is covered by warranty. Fiilex will replace or repair to proper working condition any
products that are returned under warranty. Products repaired or replaced under warranty are
under warranty only for the remaining unexpired period of time of the original warranty.
Any Product unit or part returned to Fiilex must be packaged in a suitable manner to ensure the
protection of such Product unit or parts. The package must be clearly and prominently marked to
indicate that the package contains returned product units or parts with a Return Authorization
(RA#) number. All returned product units or parts must be accompanied by a written explanation of
the alleged problem or malfunction.
1689 Regatta Blvd. Richmond, CA 94804
| [phone] | [e-mail]
www.fiilex.com
Safety
• Do NOT attempt to disassemble the body of P100.
• Do NOT install the P100 Series in a damp or wet area.
• Do NOT Cover the air vents.
• Use only the included power supply. Failure to do so may cause damage to the LED light.
• Use only a soft, dry towel to gently clean the exterior of the light.
• Disconnect electrical power before adding to or changing the configuration of the track.
• Do NOT attempt to disassemble deform, solder, or heat battery.
• Do NOT insert battery with different connector.
• If neccessary, seek certified electrician for installation assistance.
• Stop using battery if it expands or if temperature reaches over 40°C or 104°F
• Do NOT short circuit battery.