Fireco Dorgard SmartSound User manual

Compliance Made Easy
Dorgard SmartSound
Userguide
!SmartSound

Carpet and Floor Protection
If Dorgard SmartSound is holding the door open and the door is pulled, the rubber
foot may mark the flooring. Activate this feature to avoid this.
1. Using your smartphone, go to fireco.online/carpet or scan the QR code to
download the sound file
2. Remove the battery
3. Press play on the sound file with the phone next to the unit
4. Whilst the sound file is playing re-insert the batteries
5. All lights will show green to confirm the application
1.2.3.4.
SmartSound
!
!Dorgard Pro
SCAN ME TO DOWNLOAD
YOUR SOUND FILE
fireco.online/carpet

Filter Out Short Alarms
Adjust your unit to close the door after an alarm has been going off for a certain amount of time.
For example, schools often use the same sounder for fire alarms (which last for a long time) and lesson
change bells (which last only for a few seconds). This feature allows shorter alarm sounds to be ignored
so that the door remains open and only closes on the real fire alarm.
1. Using your smartphone, go to fireco.online/filter-12 or scan the QR code to
download the sound file
2. Remove the battery
3. Press play on the sound file with the phone next to the unit
4. Whilst the sound file is playing re-insert the batteries
5. All lights will show green to confirm the application
1.2.3.4.
SmartSound
!
SCAN ME TO DOWNLOAD
YOUR SOUND FILE
!Dorgard Pro
fireco.online/filter-12

Delay Door Closure
Give people more time to evacuate the building before the doors close.
This is particularly useful if there are occupants who are disabled or have limited mobility.
1. Using your smartphone, go to fireco.online/delay-60 or scan the QR code to
download the sound file
2. Remove the battery
3. Press play on the sound file with the phone next to the unit
4. Whilst the sound file is playing re-insert the batteries
5. All lights will show green to confirm the application
1.2.3.4.
SmartSound
!
!Dorgard Pro
SCAN ME TO DOWNLOAD
YOUR SOUND FILE
fireco.online/delay-60

Door Close Time
Set the unit to close the door at a chosen time.
This is useful for hotels where doors need to be kept open during the day to allow easy access but
closed at night to reduce noise.
1. Insert the mini screwdriver provided into the hole on the front of the unit and press the button
2. The unit will beep once for every hour from the current time. If the time is 4pm and you want the unit
to close the door at 8pm, you need to let the unit beep 4 times before pressing the button again
3. The unit will beep back the number of hours you have set to confirm
To change the time you have set, remove and re-insert the batteries and follow steps 1-3.
Note: If you are applying the other features, set up Door Close Time last.
1.2.3.
SmartSound
!
!
SmartSound
!x1 SmartSound
!x1
!
!

Factory Reset
By factory resetting your unit, all features applied will be removed.
1. Remove the batteries
2. Hold down the button on the front of the unit using the mini screwdriver provided and reinsert the
batteries- this must be done simultaneously
3. The unit will beep 3 times to confirm the reset
1.2.3.
SmartSound
!
SmartSound
!x3
!

Dorgard SmartSound LEDs
Radio LED not currently in use.
Fire LED
• Flashes red before door is released upon detection of an alarm
• Flashes green before door is released if night-time closure feature is used
• If fire & alert LEDs are red unit has failed to release after an alarm was detected
Alert LED
• Illuminates red on a mechanical fault or door obstruction
• (Also see last bullet points for fire LED and power LED)
Radio
Fire
Power
Alert
!
SmartSound
Power LED
Upon insertion of batteries:
• Green for 5-10 seconds if brand new batteries are inserted
• Amber for 5-10 seconds if batteries have less than 95% charge remaining
• Red for 5-10 seconds when critical battery level is reached
• If power and alert LEDs both illuminate red the critical battery level has been exceeded and
the unit will fail-to-safe. This can happen on battery insertion and during normal operation,
once batteries are depleted

Dorgard SmartSound Specifications
Power Two x LR14 C-size batteries (included)
Expected battery life Three years
Colour Black or white
Width 195mm
Height 205mm
Depth 45mm
Weight 700g
Activation SmartSound listening technology
Casing ABS plastic
Hold open positions Can hold the door at any angle
Maximum door size Power size 7 (max of 160kg and 1600mm width)
Audible warning Warns of door closing on fire or fault
Fire rating Suitable for up to 60-minute fire doors
Compliant to EN1155, EN1634, EMC Directive, Radio Equipment Directive,
CE Marked
Suitable for Standard (category B) installations under BS7273-4 2015
It is never safe to wedge open a fire door. If you need to buy more Dorgard
SmartSound give us a call on 01273 320650.