Apollo Smoke Detector XP95 User manual

Overseas offices: America China Germany
Certificate No. 010
See www.RedBookLive.com
Assessed to ISO 14001:2004
Certificate number EMS 010
MANAGEMENT
SYSTEMS
MANAGEMENT
SYSTEMS
Assessed to ISO 9001:2008
LPCB Cert No. 010
36 Brookside Road, Havant,
Hampshire, PO9 1JR, UK.
Tel: [phone]
Fax: [phone]
Email: [email protected]m
Web: www.apollo-fire.co.uk
PP2453/2013/Issue 1
XP95®Manual Call Point
FUNCTION
The XP95 Manual Call point has been designed to
operate on a loop of intelligent fire detection devices
and when activated interrupts the polling cycle for
a very fast response.
The XP95 Manual Call Point is intended for indoor
applications and is available in two versions, with
and without isolator.
FE ATURES
The XP95 Manual Call Points come complete with
the following key features:
• Resettable element
• Easy access, front reset mechanism
• Front facing addressing
• E-Z t connector system for installation
• Ergonomic reset key and keyring hole
• EN54-11 Approved
• 180° viewable LED
• Continunity link for cable insulation testing
PROTOCOL COMPATIBILITY
The XP95 Manual Call Point will operate only with
control equipment using the Apollo digital protocol.
ELECTRICAL CONSIDERATION
The XP95 Manual Call Point is loop powered and
operates at 17-28V DC for all variants.
MECHANICAL CONSTRUCTION
The component parts of the call point are moulded
in a robust fire retardant polycarbonate.
OPERATING PRINCIPLES
The address of each call point is set at the
commissioning stage by means of a seven-segment
DIL switch. The address switch is accessible without
removing the call point from the mounting surface.
XP95 Manual Call Point with Isolator 55200-908
XP95 Manual Call Point 55200-905
0832

TECHNICAL DATA
Supply voltage 17-28V DC
Communications Protocol 5 - 9V Peak to Peak
Operating temperature -40°C to +70°C
Humidity (no condensation) 0-95%RH
IP rating 45
Current Consumption (max) at 24V DC
Power Up Surge (1s typical) 1mA
Quiescent 100µA
Alarm current (LED On) 4mA
Complies with EMC Directive 2004/108/EC
Red version complies with EN54–11:2001
EN54-17:2005 (Isolated version)
A red alarm LED is provided on the call point. This
LED is controlled independently of the call point, by
the control panel.
Once activated, the XP95 Manual Call Point can be
reset by inserting the reset key into the front facing
LED, turning clockwise until a positive click and reset
occurs.
The isolated version of the XP95 Manual Call Point
incorporates a short circuit isolator which will ensure
its operation in the event of a short circuit fault on
the loop. Isolator operation is indicated by a yellow
LED. For further details of the isolator refer to data
sheet PP2090, available on request.
This Manual Call Point helps reduce installation
time as all the initial installation cabling is wired to
a removable terminal block which fits neatly in the
back of the Call Point.
DIMENSIONS AND WEIGHT
Indoor 88mm x 88mm x 59mm 180g
DIMENSIONAL DRAWING
88mm
88mm
EMC DIRECTIVE 2004/108/EC
The Manual Call Point complies with the essential
requirements of the EMC Directive 2004/108/EC,
provided that it is used as described in this data
sheet.
A copy of the Declaration of Conformity is available
from Apollo on request.
Conformity of the Manual Call Point with the EMC
Directive does not confer compliance with the
directive on any apparatus or systems connected
to it.
CONSTRUCTION PRODUCTS DIRECTIVE 89/106/
EEC
The Manual Call Point complies with the essential
requirements of the Construction Products
Directive 89/106/EEC.