Firegear LOF-30MSI/N User manual

Linear Outdoor Fire
Installation and Operating Instructions
IF YOU CANNOT READ OR UNDERSTAND THESE INSTALLATION INSTRUCTIONS DO
NOT ATTEMPT TO INSTALL OR OPERATE THIS APPLIANCE
Warning: For Outdoor Use Only
PLEASE RETAIN THIS MANUAL FOR FUTURE REFERENCE
INSTALLATION PRECAUTION:
This Linear Outdoor Fire pit requires a minimum 18-square inches (per side) of cross
ventilation. Failure to provide proper ventilation can void the warranty.
Match Throw Description Manual Spark
LOF-30MT/N 30-inch stainless burner & pan LOF-30MSI/N
LOF-36MT/N 36-inch stainless burner & pan LOF-36MSI/N
MODELS
Home Decor and Fireplaces
21701 Route 6
Warren PA 16365
1-888-986-1535

!
!! !!!"#$%&!
!
"#!$%&!'()**!+,'-!
!
1. Shut off gas to the appliance.
2. Extinguish any open flame.
3. If odor continues, keep away
from the appliance and
immediately call your gas
supplier or fire department.
!!'"&#(#$!
!
.%!/%0!'0%1)!%1!&')!+,'%*2/)!%1!%03)1!
#*,((,4*)!5,6%1'!,/7!*28&27'!2/!03)!
5292/20$!%#!032'!%1!%03)1!,66*2,/9):!
!
;/!<=>9$*2/7)1!/%0!9%//)90)7!#%1!&')!
'3,**!/%0!4)!'0%1)7!2/!03)!5292/20$!%#!032'!
%1!,/$!%03)1!,66*2,/9):!
!!!"#$%&! ! ! )"&*+#,-+#+.(!%,/"00"&!,
,
1234,56673589:,958,6;<=>9:,95;?<8,@<8<A3=:,
B2392,254,8<,<=<;C,
,
D438E,3F,38,58,:897<4:=,4659:,958,G377,H<>C,
,
#:I:;,>4:,F234,56673589:,38,58,:897<4:=,4659:,
4>92,54,5,95@6:;J,F:8FJ,95;,<;,2<@:C,
!
'"&#(#$-!!"#!03)!2/#%1(,02%/!2/!03)')!2/'01&902%/'!2'!/%0!#%**%?)7!)@,90*$A!,!#21)!%1!
)@6*%'2%/!(,$!1)'&*0!9,&'2/+!61%6)10$!7,(,+)A!6)1'%/,*!2/B&1$!%1!7),03:!
!
K+&,L+D&,M"K%1L,
.%!/%!'0%1)!%1!&')!+,'%*2/)!%1!%03)1!#*,((,4*)!5,6%1'!,/7!*28&27'!2/!03)!5292/20$!%#!
032'!%1!,/%03)1!,66*2,/9):!
!
!
!! !!'"&#(#$!
"(61%6)1!2/'0,**,02%/A!,7B&'0()/0A!
,*0)1,02%/A!')1529)!%1!(,2/0)/,/9)!9,/!
9,&')!2/B&1$!%1!61%6)10$!7,(,+):!!C),7!
03)!2/'0,**,02%/A!%6)1,02/+!,/7!
(,2/0)/,/9)!2/'01&902%/'!03%1%&+3*$!
4)#%1)!2/'0,**2/+!%1!')15292/+!032'!
)8&26()/0!!!!!!
'"&#(#$,
.%!/%0!*),5)!&/,00)/7)7!7&12/+!&'):!
.%!/%0!&')!#%1!9%%D2/+:!
E%**%?!,**!+,'!*),D!61%9)7&1)'!2/!032'!
(,/&,*!612%1!0%!%6)1,02%/:!
REV 10-21-13 Page 1
Linear Outdoor Fire

!
"#$%&!#&$'!()!*+&!,(-$'!+..%(+)/$&0!+)'!12$!.-3'#/1&!3,!/345#&1(3)!3,!&#/2!,#$%&0!/3)1+()!
/2$4(/+%&!6)37!13!12$!81+1$!3,!9+%(,3-)(+!13!/+#&$!/+)/$-0!5(-12!'$,$/1&!+)':3-!312$-!-$.-3'#/1(;$!
2+-4<!=2(&!7+-)()*!(&!(&&#$'!.#-&#+)1!13!9+%(,3-)(+!>$+%12!?!8+,$1@!93'$!8$/<ABACD<E!
REV 10-21-13 Page 2
Specifications 3
Preparation for Non-Conbustible Structure 4
Hard Piping to Linear Outdoor Fire 4
Cross Ventilation Requirements 4
High Elevation 4
Installation into an Approved Enclosure 5
Requirements 5
Installing Key Valve & Peso Ignitor 5
Typical Installation Drawings 6
Installing Battery in Piezo Ignitor 7
Ignitor Alignment 7
Installation of Lava Rock/Media 7
Operation 8
Lighting Instructions 8
Air Shutter Adjustment 8
Replacement Parts 9
Replacement Parts List 10
Linear Fire Maintenance/ Trouble Shooting 11
Optional Accessories/Conversion Kits 11-12
Warranty 13
TABLE OF CONTENTS
NOTE: This installation instruction covers both Match Throw and Manual Spark
Ignition systems. Not all sections will be applicable to your particular application.
Linear Outdoor Fire

If this Linear Outdoor Fire (LOF) is permanently connected
to a gas piping system from a remote supply tank, installa-
tion must be in accordance with local codes or, in absence
of local codes, with the National Fuel Gas codes ANSI
Z223/1/NFPA 54.
If constructing an enclosure to conceal a propane•
tank/LP cylinder- the enclosure must adhere to the fol-
lowing construction requirements:
Enclosures may be constructed with one side•
completely OPEN or if the enclosure is built with four
(4) sides, a top and a bottom, then as follows:
A Propane/LP gas cylinder enclosure requires four•
(4) ventilation openings at the top and bottom of the
enclosure. The openings must adhere to the minimum
requirements according to the capacity of the cylinder
(See diagram 1).
Each opening in the enclosure must be equally sized•
and spaced at a minimum of 180º. Openings must
remain unobstructed.
Top ventilation openings are required on the side walls•
of the enclosure within 5-inches (127mm) of the top
enclosure. They need to be of equal size,
unobstructed and spaced 180º apart. The openings
need to be a total area of 1 in²/lb (14.2 cm²/kg) of fuel
storage capacity.
Bottom opening must provide a minimum of 1/2•
square inches (3.23 cm²) for each pound of propane/
LP
contained in the tank (see example below.
Every opening must have minimum dimensions to allow•
entrance of a 1/2” (3.2 mm) diameter rod.
Ventilation openings in side walls must not communi-•
cate directly with other enclosures of the Linear Out-
door Fire pit.
The cylinder valve must be easily accessible by hand.•
Connections should be easy to leak test inside the
enclosure. A door on the enclosure is acceptable only if
easily opened without the use of tools and is non
locking.
The enclosure needs to be isolate the cylinder from the•
burner compartment and provide protection from
radiation,actasaflamebarrierandprotectcylinder
from foreign material.
The enclosure needs to allow connection, disconnec-•
tion and inspection of the connection of the LP gas
cylinder.
The enclosure should allow testing of any connection•
on the LP cylinder that might be disturbed during
installation.
REMOTE PROPANE / LP GAS ENCLOSURES
INSTALLATION GUIDELINES
5” Max.
5” Max.
2” Min.
1” Max.
A
C
B
Diagram 1.
Propane/LPTankEnclosureSpecifications
A - Opening 180º apart from each other
BMin.2”(50.8mm)fromfloor/groundtobaseoftank
C - Max. 1” (25.4mm) from tank base to bottom of opening
Most Linear Outdoor Fire’s are equipped for Natural gas (NG) however, if you are considering converting
to LP gas use the guidelines below for proper tank storage.
REV 10-21-13 Page 3
Linear Outdoor Fire

SPECIFICATIONS
Table1. Linear Pan Dimensions
36”
96”
24”
Maximum
Overhang
Center of Flame
!
A
B
C
.875 TYP. (usable flat lip)
*
*
D
Ground Level
Figure 1. Linear Pan dimensions; refer to Table 1.
Figure 2. Clearance to Combustibles
(Not to be used in an enclosed space)
REV 10-21-13 Page 4
Model Btu’s
Natural/Propane (LP)
FactoryOrifice
NG LP
LOF-30MT/N 45,000 Btu’s #36 #49
LOF-36MT/N 75,000 Btu’s #29 #41
LOF-30MSI/N 45,000 Btu’s #36 #49
LOF-36MSI/N 75,000 Btu’s #29 #41
NG LP
Min.
Inlet
5.0”WC 11.0”WC
Max.
Inlet
10.5”WC 13.0”WC
Table 3. Gas Pressures
Model A
Pan Depth
B
Min/Max Opening Width - Length
C
Inside Pan
D
Ground Level
LOF-30MT/N 2.75” 6.25”- 7.5” W x 30.25” - 31.75” L 30” 6”
LOF-36MT/N 2.75” 6.25”- 7.5” W x 36.25” - 37.75” L 36” 6”
LOF-30MSI/N 2.75” 6.25”- 7.5” W x 30.25” - 31.75” L 30” 6”
LOF-36MSI/N 2.75” 6.25”- 7.5” W x 36.25” - 37.75” L 36” 6”
Note: Linear Outdoor Fire’s are rated at maximum Btu’s which is dependent upon proper gas pipe sizing. Flex line
sizealsoaffectBtu’s.AsaresultyourBtu’swillmayvaryfromTable2specificationslistedabove.
Table2:BtuSpecificationsbasedon7.0”WCNGand10.0”WCLP
Linear Outdoor Fire

REV 10-21-13 Page 5
WARNING: Proper clearances from combustible, construction and materials must be maintained from all sides, top and
bottom of this appliance. This appliance should never be placed on any combustible surface. This appliance should
never be placed under any combustibles closer then 96-inches. This appliance should never be placed closer than
36inchesfromanysidetoanycombustibleconstructionormaterials(Seefig.2,pg.3).
PREPARING A NON-COMBUSTIBLE STRUCTURE
TheLinearOutdoorFireistobeinstalledonaflat,stablesurface,awayfromanycombustiblematerials.InstallLinear
Outdoor Fire on any level, outdoor non-combustible surface. NOTE: Do not place Linear Outdoor Fire directly on grass,
dirt, or rocks this may prevent proper ventilation (Fig. 1, pg. 3). Ensure proper water drainage is also incorporated
into the Linear Outdoor Fire enclosure.
HARD PIPING TO Linear Outdoor Fire pit WITHOUT GAS PROXIMITY
NOTE: We recommend using a minimum ¾” black iron pipe however refer to the NFPA54 (National Fuel Gas Code) for
proper pipe sizing when exceeding 20-feet in length for Linear Outdoor Fire’s rated above 100,000 Btu’s.
1. Turn OFF gas supply system. NOTE: All gas connections (except for brass to brass) require the following. Clean pipe
threadsusingeitherawirebrushorsteelwool.ApplyTeflontapeorpipesealanttothesteelfittingsbeforemakingany
connection. BE CAREFUL! Ensure all gas connections are snug, but not over tighten!
2. Extendthegassupplysystemusingminimumof¾”blackironpipeoranapprovedflexiblegaslinefromexistinghouse
supply. This can be accomplished by teeing off or tapping into a convenient gas line connection. Install necessary pipe
for the distance required and then install a manual shut-off valve at the exterior house wall. If pipe is to pass through a
foundation or house wall, make sure to re-seal the area around the pipe with weather sealant.
3. From manual valve, extend gas pipe to the Linear Outdoor Fire location. NOTE: If pipe is to be placed in an under-
ground trench, check with local codes for required depth and materials needed.
4. Installa¾”femalex½”maleflaredbrassfittingtotheendofthe¾”blackironpipe.Besuretocleanthepipethreads
anduseTeflontapeorpipesealant.
5. Connectthe½”femaleflaredflexconnectorfromtheLinearOutdoorFiretothe½”maleflaredbrassfittingsecuredto
the black iron pipe. Note:FlaretoflareconnectionsdonotrequireTeflontapeorpipesealant.
IMPORTANT
InstallationofNaturalorLPgasshouldbedonebyaqualifiedinstaller,serviceagencyorgassupplier.
The appliance and its manual shutoff valve must be disconnected from the gas supply piping system during any
pressure testing of the system at test pressure testing of the system at test pressures in excess of ½psig (3.5kPa).
This appliance must be isolated from the gas supply piping system by closing its manual shutoff valve during any
pressure testing of the gas supply piping system at test pressures equal to or less than ½psig (3.5kPa)
NOTE: LP conversion kits are available in the Accessory/Con-
version Kit section of this manual. When converting a Linear
Outdoor Fire ensure you follow the instructions supplied with the
conversion kit.
VENTILATION FOR NON-COMBUSTIBLE ENCLOSURE
Linear Outdoor Fire’s are subjected to many outdoor
elements such as rain, snow, wind, heat or cold. A minimum
of 18 square inches of cross ventilation (2 sides) is
required to keep the components in good working order.
Usefigure3asguidetoassisttoincorporateproper
ventilation. NOTE: Ventilation is not required at the bottom, it
may also be incorporated in the upper portion of an enclosure.
Figure 3. Cross Ventilation Example
HIGH ELEVATION INSTALLATION
This appliance is listed for elevations from 0-4500 feet in
Canada and the U.S. If elevation exceeds 4500 feet it may be
necessary to decrease the input rating by changing the exist-
ingburnerorificetoasmallersize.Inputshouldbereduced
4% for each 1000 feet beyond the 4500 feet above sea level.
Check with your local gas utility for assistance in determining
theproperorificeinyourlocation.Insomecasestheheating
valuemayalreadybereducedanddownsizingtheorificemay
not be necessary.
Linear Outdoor Fire
Fire Pit
Enclousure
2”x3”
Linear Pan
Examples of Cross Ventilation
3 - 2”x3” Slots Per Side or
2- 1”x 9”Slots Per Side
Cross Flow Ventilation
(Min. 18 Sq. In. Per Side)

REQUIREMENTS
1. Only non-combustible materials should come in direct contact with any part of the Linear Outdoor Fire. Under
neath area should be non-combustible as well.
2. Only a minimum ¾” gas supply line to the Linear Outdoor Fire. Based on the selection of the Linear Outdoor Fire
size,theproperbrassfittingsshouldbeusedtoensureaproperinstallation.
3. Determine the size of the round or square Linear Outdoor Fire you are preparing to install (Refer to page 3).
4. You must provide a rectangular opening out to place the Linear Outdoor Fire into the non-combustible
enclosure surround. Do not exceed the maximum opening from Table 1, dimension B.
5. Follow the local code requirements for the gas type being used. This Linear Outdoor Fire should be installed in
accordance with local codes and ordinances or in the absence of local codes, with the latest National Fuel Gas
Code, ANSI Z223.1 NFPA54 or CSA B149.1, Natural and Propane Installation Code in Canada.
6. Linear Outdoor Fire pits create high temperatures, it is very important to have any combustibles at a safe distance
See Fig. 2 page 4).
7. CAUTION: A minimum of 18 square inches of cross ventilation (per side) is required to keep the enclosure
dry.
8. These products are designed for outdoor use only. Not approved for any indoor use.
9. This Linear Outdoor Fire is designed to have Lava Rock/Media completely covering the burner tube so that the
burner is invisible. Do not cover more than 1” above the top of the burner. When purchasing Lava Rock it is recom
mendedtouseminimumof1”diameterasabasetofilltheburnerpan.Decorativeglasscoveringmaybeloosely
scatteredontopoftherockifdesiredornoncombustiblelogsmaybeaddedforacampfirelook.Iflogsare
chosen, do not place on decorative glass base, use only Lava Rock as the base. NOTE: If using all glass media,
glass must be a minimum of 1/4-inch diameter or larger.
10. Gaslinesandfittingsmustbeinstalledintothenoncombustiblestructure.Allgasconnectionsmustbeleaktested
before installation of the Linear Outdoor Fire. Soapy water leak detection is required before regular use of the
Linear Outdoor Fire.
11. Do not use material that will absorb moisture over time and will not release this moisture quickly. Moisture can boil
in this material and can rapidly break apart and cause damage or personal injury.
12. Never leave any other combustible material on top of the Linear Outdoor Fire. This could cause unsafe operation
of this system and damage to the component that will not be covered under our warranty.
13. Cover the complete burner with lava or decorative Rock material (min. 1-inch diameter). Completely cover the
starburner,nomorethan1inchabovethefirestarburner.
INSTALLATION OF Linear Outdoor Fire pit INTO AN APPROVED
REV 10-21-13 Page 6
INSTALLING KEY VALVE AND PIEZO IGNITOR
Thekeyvalvecontents:1keyvalve,1keyand1flange.(Seefigure4).Thevalverequiresa11/4”roundclearance
holeinthenoncombustibleenclosurewall.Seetheinstructionssuppliedwiththekeyvalveformorespecificdetails.
Note:Besuretoleaktestallfittingbeforeoperation.Figure5showsanexampleofatypicalinstallation.
After the Linear Outdoor Fire burner pan is installed run the Piezo ignitor wires into the electrical junction box. Piezo wires
are 24-inches in length; ensure your installation does not exceed the wire length for proper connection.
Primary Gas
Supply
ON
OFF
Fig. 4 Key valve components.
Linear Outdoor Fire

REV 10-21-13 Page 7
Manual Spark
Piezo Ignitor
Key Valve
Gas Supply
Linear Pan
Non-Combustible
Fire Pit Enclousure
Shut-O
Key Valve Flange
Non-
Combustible
Wall Material
Non-
Combustible
Wall Material
Key Valve
Primary Gas
Supply
K
e
y
V
a
l
v
e
S
i
d
e
V
i
e
w
D
e
t
a
i
l
Non-
Combustible
Wall Material
Non-
Combustible
Wall Material
Securing Tab
Securing Tab
Self-Securing
Junction Box
Piezo Ignitor
Mounting Plate
Piezo Wires
P
i
e
z
o
I
g
n
i
t
o
r
S
i
d
e
V
i
e
w
D
e
t
a
i
l
Fig. 5 Typical installation.
NOTE:Gassupplyshutoffandflex
line to the key valve are not supplied.
Linear Outdoor Fire

REV 10-21-13 Page 8
INSTALLATION OF LAVA ROCK/MEDIA INTO BURNER PAN
Install lava rock/media into the burner pan. Ensure the media is a minimum of
1-inch diameter for proper operation. Note: Do not pour Lava Rock directly from
bag.MediashouldbeplacednaturallyandNOTpackedintight.Loosefittingis
importanttoensurerobustflames.Besurerocksarefreeofanyexcessivedust.
This prevents the burner pan weep holes from being plugged and holding water.
IMPORTANT: Do not place media over top or under the screen cover. The
screen must be free of any debris to ensure proper lighting of burner and good
flamerectification(Seefig.8).
Cover the burner completely with media but do not make the depth greater than
1-inch overtop of the burner portholes.
Decorative glass may be loosely scattered on top of the lava rock. Do NOT
cover the stainless steel screen cover with any rock or glass. It must be free an
any debris to operate properly.
Fig. 6 Piezo ignitor cap.
+-
AAA
Fig. 7 Piezo ignitor battery installation.
Unscrew (counter-clockwise) the Piezo ignitor module red button cap and the plastic mounting nut. Slide the module on
the back side of the module cover plate and secure with the plastic mounting nut. Insert the positive end of (1) AAA
battery into the ignitor module and carefully screw the red button cap to the ignitor module until snug. Careful not to over-
tighten the cap. Attach the extension wires (PIEZO23WH/25WH) to the 2-probe spark ignitor. Careful not to overtighten
the cap. Test the ignitor by pushing and holding the red button to ensure the ignitor probes inside the Linear Outdoor Fire
aresparking.Thesparkshouldbelocateddirectlyovertopoftheburnerportholeforproperignitionofthegas(Seefig.8).
Spacing between the probes should be approximately 1/8-inch for proper spark.
Fig. 8 Proper ignitor probe location.
Lava Rock Lava Rock
Lava Rock
Ignition Hood
Screen Cover
Fig. 9 Keep screen cover exposed
INSTALLATION OF BATTERY INTO PIEZO IGNITOR (Manual Spark Ignition only)
IGNITOR ALIGNMENT (Manual Spark Ignition only)
For proper ignition it is important that the ignitor probes be properly
aligned overtop of the burner port holes. Use the Fig.8 as a guide.
Before lighting remove the screen cover of the ignition hood to
burner and ensure the spark probes are directly overtop of a burner
porthole.Thesparkingprobesmustbeinthepathofaflameto
ignitethegasforproperignitionoftheflame.
Replace the screen cover and follow the operating instructions.
Linear Outdoor Fire
Burner Pan
Ignitor
Shield
Max. 1/8”
Spacing

REV 10-21-13 Page 9
CAUTION: Children and adults should be alerted to the hazards on high surface temperatures and should stay away to
avoid burns or clothing ignition. Young children should be carefully supervised when they are in the area of the appliance.
WARNING:Donotusethisapplianceifanyparthasbeenunderwater.Immediatelycallaqualifiedservicetechnician
to inspect the appliance and to replace any part of control system and any gas control, which has been under water.
OPERATION
SAFETY WARNINGS
1. Never leave the Linear Outdoor Fire unattended during operation.
2. Clothingorotherflammablematerialsshouldnotbeplacedonorneartheappliance.
3. Any guard or other protective device removed for servicing the appliance must be replaced prior to operating the
appliance.
4. Installationandrepairshouldbedonebyaqualifiedserviceperson.Theapplianceshouldbeinspectedbefore
useandatleastannuallybyaqualifiedserviceperson.Morefrequentcleaningmayberequiredasnecessary.It
is imperative the control compartment, burners and circulating air passageways of the appliance be kept clean.
5. Inspect the fuel supply connection before each use of the appliance.
6. Temporary storage of this appliance indoors is permissible only if it has been disconnected from its fuel supply
(Natural or L.P. gas line).
WARNING
1. This appliance is hot when operated and can cause sever burns if contacted.
2. Do not burn any solid fuels in this appliance.
READ ALL LIGHTING INSTRUCTIONS BEFORE ATTEMPTING TO LIGHT Linear
Outdoor Fire pit
CAUTION: Ensure you have leak tested the Linear Outdoor Fire before operating.
1. Insert key into gas valve.
2. Push and hold the red button on the manual Piezo ignitor and ensure sparking is
occurring at the probes inside the Linear Outdoor Fire.
3. Rotatethekeycounterclockwiseingasvalvetoallowgastoflow.
4. Gas should ignite within 10 seconds or less. If Linear Outdoor Fire does not light
within
10 seconds turn key clockwise to turn OFF the gas supply. Check ignitor probe
location (Fig. 8), ensure there is an 1/8” gap between the probes with a good strong
spark then repeat steps 2 through 4.
OnceLinearOutdoorFire’slights,flamecoloradjustmentcanbemadeturningtheair
shutter nut under the burner pan. It is recommended that the nut be OPENED until the
gas/air mixture makes a rushing sound (like a blow torch); then slowly CLOSE until the
rushingsounddiminishes.Adesirableflameisbrightyellowwithlittleornobrownat
thetips.Tooyellowflamecancreateexcessivesooting(Seefig.10).
Fig. 10 Air shutter adjustment
MANUAL SPARK IGNITION LIGHTING INSTRUCTIONS
MATCH THROW LIGHTING INSTRUCTIONS
READ ALL LIGHTING INSTRUCTIONS BEFORE ATTEMPTING TO LIGHT THE Linear Outdoor Fire pit
CAUTION: Ensure you have leak tested the Linear Outdoor Fire before operating.
1. Insert key into gas valve.
2. Light a long match or butane lighter and hold it near the burner.
3. Rotatethekeycounterclockwiseingasvalvetoallowgastoflowandsimultaneouslyapplytheburningmatchas
close to burner as possible to light the Linear Outdoor Fire.
4. Gas should ignite within 10 seconds or less. If Linear Outdoor Fire does not light within
10 seconds turn key clockwise to turn OFF the gas supply. Ensure there is not too much media on top of burner that
mightinhibitgasflowandtryagain.
Linear Outdoor Fire

REV 10-21-13 Page 10
REPLACEMENT PARTS
1
2
5
3
4
ON
OFF
Side View
6
15
7
9
10
11
14
Linear Outdoor Fire
12
13
+-
AAA
8
10
16

REV 10-21-13 Page 11
1 30” Linear Burner Tube 1 ST3-200-1000
1 36” LInear Burner Tube 1 ST3-200-1001
2 30” Linear Burner Pan 1 ST3-100-1042
2 36” Linear Burner Pan 1 ST3-100-1044
3 Cover Plate 1 ST3-100-1043
4 Cover Plate Screw 2 ST3-113-1030
5 Ignitor Shield 1Available Soon!
6 Silicone Rubber Washer 1 213S70
7 7/8” Flat Washer/Spacer 1 ST3-113-1026
8 1/2” Flex Gas Line (46-inch Length) 1 T-200-9898-46
9OrificeAirShutter(LOF30NG) 1 OA/S#36
9OrificeAirShutter(LOF30LP) 1 OA/S#49
9OrificeAirShutter(LOF36NG) 1 OA/S#29
9OrificeAirShutter(LOF36LP) 1 OA/S#41
10 Manual Spark Ignitor Module 1 ST3-040-1020
10 Manual Spark Ignitor Module Cover Plate (w/Screws ) ST3-100-1035
11 2-Probe Manual Spark Ignitor 1Available Soon!
12 AAA-Battery 1 ST3-060-1004
13 Junction Box - With Self Securing Tabs 1 FG-Junction Box
14 Std.Capacity Straight Ball Valve 1 BVS
15 8-inch Chrome Key for BVS 1 KEY-PC/8
16 Chrome Flange (decorative chrome cover for BVS) 1 FP.BV.CR.B
Item Description Qty. Part Number
REPLACEMENT PARTS
Linear Outdoor Fire

MAINTENANCE
1. TheLinearOutdoorFireshouldbeinspectedandcleanedbeforeinitialuseannuallybyaqualifiedfieldserviceperson.
2. Any component that is found faulty must be replaced with an approved component.
3. Any tampering or modifying with the Linear Outdoor Fire is dangerous and voids all warranties.
4. During winter months in cold climates and various seasons operation the Linear Outdoor Fire may be affected by
weather conditions. It is recommended to use a ventilated cover overtop of your Linear Outdoor Fire to protect it from
humid/rainy weather conditions when not in use. Heavy rains/downpours could affect the Linear Outdoor Fire operation if
not covered; if this occurs ensure you allow the Linear Outdoor Fire time to dry out before attempting to operate. NOTE:
If a combustible type cover is used over the Linear Outdoor Fire when not in use be sure to remove it before operation to
prevent a severe safety hazard.
5. Carbon (soot) may build up on the surface of logs (if installed) during heavy use. Sooting may also occur periodically
on the screen of the ignitor hood. To clean, brush off with a dry bristle brush or cloth. Keep soot away from clothing or
furniture.
6. Over time stainless steel parts discolor when heated, usually a golden or brown hue. This discoloration is normal and
does not affect the performance of the appliance.
REV 10-21-13 Page 12
TROUBLE SHOOTING
Symptom Remedy
Piezo Won’t Spark 1. Be sure battery is installed properly.
2. Check battery voltage. Min. 1.2 volts needed.
3. Check ignitor gap at probes inside Linear Outdoor Fire. Gap should be at 1/8”.
4. Double check wires to ensure they are plugged in and secured to the spark ignitor and the
spark ignitor module.
LOFWon’tLight 1. Ensureignitorisalignedproperlyovertopofburnerporthole.Seepage7,figure8.
2. Bleed gas line.
3. Ensure all gas supply lines are turned ON.
4. Ensurethereisnottoomuchmediaovertopofburneritcaninhibitgasfromflowing.
Low Flame 1. Ensure the base media is at least 1-inch in diameter and top media is no more than 1-inch over
top of burner.
2. Adjust air shutter at bottom of Linear Outdoor Fire pit pan.
3. Ensureallshutoffvalvesandkeyvalveisfullyopen.Seepage8figure10.
Water in Fire Pit 1. Excess dust/sand material from media may be blocking the weep holes to relieve water.
Remove all media and unplug weep holes. Clean or install new media free of dust and dirt.
2. Ensure Linear Outdoor Fire pit enclosure has proper drainage for water and proper ventilation
to dry out.
Linear Outdoor Fire

MODEL: O/AS#49
LP Conversion Kit for LOF-30MT/N
MODEL: O/AS#41
LP Conversion Kit for LOF-36MT/N
FOR TECHNICAL SERVICE, CALL: [phone] Ext. #3
REV 10-21-13 Page 13
CONVERSION KITS
OPTIONAL ACCESSORIES
The following accessories are available from your local firegear dealer/distributor. Each accessory comes with a separate
installation manual. Read each instruction thoroughly before installing.
Lava Boulders 3” to 6” size (30lbs.)
Model: FG-LB30
Lava Stones 1” to 2” size. (20lbs.)
Model: FG-LS20
LP regulator with 3/8” MPT adapter
Model: FG-LPRK
3/8” Quick connect 12’ hose for NG or
LP gas Model: FG-12QDK
Linear Outdoor Fire

REV 10-21-13 Page 14
The manufacture hereby warrants to the ORIGINAL
PURCHASER of this Linear Outdoor System, that it
will be free from material and workmanship defects
that prevent safe and correct operation of the product
com-mencing from date of purchase from CJ's Home
Decor and Fireplaces
Consumer/Non-Commercial Applications
Stainless Steel Burner Pan 5 Years
Stainless Steel - Burner Tube 5 Years
Stainless Steel - Valve Box (if applicable) 5 Years
Manual Valve & Spark Ignitor Assembly 1 Year
Commercial Applications
Stainless Steel Burner Pan 1 Year
Stainless Steel - Burner Tube 1 Year
Stainless Steel - Valve Box (if applicable) 1 Year
Manual Valve & Spark Ignitor Assembly 1 Year
When assembled, installed and operated in accordance
with the accompanying printed instructions.
The manufacture may require reasonable proof of your
date of purchase. YOU SHOULD RETAIN YOUR
SALES SLIP OR INVOICE AND RETURN THE
WARRANTY REGISTRATION CARD WITHIN 30 DAYS
OF PURCHASE.
This Limited Warranty shall be valid and limited to,
theoriginalpurchaseronly,withintheconfinesof
the original site installation.
WARNING:Anymodificationtothisproductwill
void the warranty!
This Limited Warranty shall be limited to the repair
and/or replacement of parts that prove defective
under normal use and service and which on
examination shall indicate, to manufactures
satisfaction, that they are defective. Before
returning any parts, contact CJ's Home Decor and
Fireplaces. If the manufacture confirmsthedefect
andapprovestheclaim,the manufacture will
replace such parts without charge.
The Owner must provide a bill of sale, canceled
check, or payment record to verify purchase date
and establish warranty period. Travel, diagnostic
cost, service labor to repair the defect and freight
charges on warranty parts to and from the fac-tory
will be responsibility of the owner. CJ's Home
Decor and Fireplaces and the manufacture will not
be responsible for labor charges and/or damage
incurred in installation, repair, and replacement or
for incidental or consequential damages.
This Limited Warranty does not cover any failures
oroperatingdifficultiesduetoaccident,abuse,
misuse, alteration, misapplication, vandalism,
improper installation or improper maintenance or
service, or failure to perform normal and routine
maintenance.
Damage due to severe weather conditions such as
Hail, Hurricanes, Earthquakes, Tornadoes, Acts of
Terrorism, Discoloration due to over heating,
Exposure to chemicals (including salt), either
directly or in the atmosphere, or Very high humid-
ity, is not covered by this Limited Warranty.
There are no other express warranties except as
set forth herein and any applicable implied
warrantiesofmerchantabilityandfitnessare
limited in duration to the period of coverage of this
express written Limited Warranty. Some states do
not allow limitation on how long an implied war-
ranty lasts, so this limitation may not apply to you.
Cj's Home Decor and Fireplaces and the
Manufacture is not liable for any special, indirect or
consequential damages. Manufactures liability is
limited to the purchase price of this fire pit System.
Some states do not allow the exclusion or limita-
tion of incidental or consequential damages, so
this limitation or exclusion may not apply to you.
The manufacture does not authorize any person or
company to assume for it any other obligation or
liability in connection with the sale, installation,
use, removal, return, or replacement of its equip-
ment; and no such representations are binding on
the manufacture.
This Warranty applies only to products sold at
retail and manufactured by:
LIMITED WARRANTY
Linear Outdoor Fire