FireplaceXtrordinair 4415 HO ST User manual


4415 HO ST - Driftwood Log Set
Installation Instructions (SKU94500976)

Page 1 of 12 17602107 — 12/12/19 © Travis Industries, Inc.
Compatibility
4415 HO ST GSR2 - SN# 3216-001942 or greater
Packing List
10 piece log set (see below)
(1) #35 Stone Locating Tab (1) #13 Stone Locating Tab
(7) Log Locating Plate (1) #10 Stone Locating Tab
(1) #32 Stone Locating Tab (18) Screws - 8x3/8” - Black
(f)
(c)
#35 Stone
#10 Stone
(e)
#32 Stone
(d)
#13 Stone
(a)
(b)


4415 HO ST - Driftwood Log Set
Installation Instructions (SKU94500976)

Page 2 of 12 17602107 — 12/17/19 © Travis Industries, Inc.
Tools Required
Philips Screwdriver
Installation Notes
WARNINGS:
Make sure the gas control valve is OFF and the heater is cool prior to conducting service.
Failure to position the parts in accordance with these diagrams or failure to use only parts specifically approved
with this appliance may result in property damage or personal injury.
HINTS:
The fireplace should be in place, with the gas line and vent attached and the firebacks installed (see owner’s
manual for further details).
If using propane (LP), convert the appliance before installing the logs (see the owner’s manual for details).
Mounting Hardware Installation
Remove the glass frame assembly to gain access to the firebox (see manual for details).
The map below shows the location of each of the log locating plates and stone locating tabs
in relation to the media tray. Look in the approximate location indicated and you will notice
holes that are slightly smaller than the others (see picture below – these holes are hard to
find – use a flashlight if necessary). These smaller holes receive the screws that secure the
tab/plate to the media tray.
Attach the appropriate tab/plate to the media tray using the included screws. Make sure the
tab/plate is facing the correct direction. Do not over-tighten the screws.
KEY
L = Log Placement plate.
#xx tabs refer to the number stamped on the stone tab (and corresponding stone).
The arrow ( ) points to the bent up portion of the stone placement tab (see
illustration to the right).
REAR OF FIREPLACE (Non-Service Side)
FRONT OF FIREPLACE (Service Side)
L
L
L
L
Small holes indicate
location of tabs
L
L L
#35
#10
#13
#32


4415 HO ST - Driftwood Log Set
Installation Instructions (SKU94500976)

Page 3 of 12 17602107 — 12/12/19 © Travis Industries, Inc.
Log, Stone, and Crushed Glass Placement
Overview - 4415 HO ST:

Log and Stone Installation Details
The logs are fragile, especially after being exposed to heat.
You may wish to measure out the amount of crushed glass needed for the installation (see the
final page of this instruction sheet) and place one layer of crushed glass on the rear of the glass
support and burner. Placing the glass at the rear is easiest at this step of log installation. Do not
place glass on the left back corner (this is where the arched log is placed.
Place log (b) on the media tray as shown below. Note that the branch on the log is on the left side. The posts on
the log supports insert into the holes on the bottom of the log.
(e)
(b)
(a)
(d) #13 Stone #32 Stone #10 Stone
(c)
#35 Stone
(f)


4415 HO ST - Driftwood Log Set
Installation Instructions (SKU94500976)

Page 4 of 12 17602107 — 12/12/19 © Travis Industries, Inc.
Place the #13 stone as shown below (the number is printed on the back of the stone). Note how the slot on the
stone fits over the tab on the stone support. The printed number on the stone faces the rear of the firebox.



4415 HO ST - Driftwood Log Set
Installation Instructions (SKU94500976)

Page 5 of 12 17602107 — 12/12/19 © Travis Industries, Inc.
Place the (a) log as shown below. The post on the log support insert into the holes on the bottom of the log.
NOTE: This is the only log that is placed over the burner.