FireplaceXtrordinair 564 25K User manual

564 SS & 25K Fireback Installation
96100179, 96100187, 96100192, 96100270, 96100204
Page 1 of 6 17601465 - 1/23/20 Travis Industries, Inc.
Compatibility
564 SS 564 25K 564 25k CF
Packing List
Rear Fireback (2) Side Firebacks

(2) Floor Firebacks
The firebacks are fragile (especially the rear fireback). Take care when handling the firebacks.
WARNING Turn off gas to the appliance and make sure it has fully cooled prior to conducting service.
564 25K (Standard or CleanFace) Installation (for 564 SS units see page 5)
NOTE On two-sided firebacks make sure to use the desired pattern.
NOTE: If using an optional fireback install the kit prior to performing any other firebox setup.
WARNING: Turn off gas to the appliance and make sure it has fully cooled prior to conducting service.You may need
to change the configuration of the firebox depending on which fireback option is being installed. Carefully review the
information below before proceeding with firebox setup.
1. Remove the glass frame and logs (see the installation manual for details).
2. Firebox baffle and exhaust restrictor must be removed to install firebacks (replace once firebacks in place).












Firebox Ceiling
The baffle and exahaust restrictor have keyholes, allowing
removal without removing the screws.
Firebox Baffle

564 SS & 25K Fireback Installation
96100179, 96100187, 96100192, 96100270, 96100204
Page 2 of 6 17601465 - 1/23/20 Travis Industries, Inc.
3. Rear Air Deflector (behind the rear log) Must be Removed (replace after firebacks in place)
Remove the rear burner.
NOTE: when replacing make sure the
burner is properly aligned and the holes on
the tabs on the burner insert over the pins
o
n
t
he bu
r
ne
r
s
t
and
.
a
IDB01282
4. Remove and discard the media tray covers

564 SS & 25K Fireback Installation
96100179, 96100187, 96100192, 96100270, 96100204
Page 3 of 6 17601465 - 1/23/20 Travis Industries, Inc.
Media Tray Configuration
Ceramic Firebacks (except for Ledgestone): The media tray is unchanged (the tabs on the side and back of the
media tray remain bent out). The firebacks will rest on the bent out tabs of the media tray.
The side and back
firebacks rest on top
of these tabs.
Ledgestone Firebacks: The media tray must be removed from the firebox and reconfigured for the ledgestone
firebacks. With the media tray removed, bend the tabs inwards (as shown below) and reinstall the media tray into the
fireplace. The firebacks will rest to the side of the media tray, on the firebox floor.
Bend these tabs inwards
(both sides).
These tabs are
shipped in the bent
out position.

564 SS & 25K Fireback Installation
96100179, 96100187, 96100192, 96100270, 96100204
Page 4 of 6 17601465 - 1/23/20 Travis Industries, Inc.







b






c
5/16" Nutdriver
a
5. Restore the fireplace to the correct configuration
Remove the clips on both sides
(these clips have key-holes,
allowing removal without removing
the screw) Place the rear fireback in position.
The side fireback holds the rear
fireback in place – support the rear
fireback while installing the side
fireback.
Place the side
firebacks in position.
Secure using the
screws and clips
removed in step “a”
NOTE: The fireback floor pieces are note
used in this application. Discard the floor
pieces

564 SS & 25K Fireback Installation
96100179, 96100187, 96100192, 96100270, 96100204
Page 5 of 6 17601465 - 1/23/20 Travis Industries, Inc.
564 SS Installation (for 564 25K units see page 1)
NOTE On two-sided firebacks make sure to use the desired pattern.
1. Remove the glass frame and logs (see the installation manual for details).
2. Remove the grate (replace after fireback installation). Remove and discard the hearth plate.
Remove the grate
(replace after fireback installation).
1/4" Nutdriver











Remove and discard
the hearth plate
Loosen this screw and
slide the bracket up.

564 SS & 25K Fireback Installation
96100179, 96100187, 96100192, 96100270, 96100204
Page 6 of 6 17601465 - 1/23/20 Travis Industries, Inc.
3. Install the firebacks following the directions below.






Place the rear fireback in place. The side
fireback holds the rear fireback in place -
hold the rear fireback while installing the
side fireback.
Remove the clip located on the
firebox ceiling near the front (both
sides). The side fireback clip has
a keyhole slot. It can be removed
by loosening the screw and
sliding the clip out.
Place the side firebacks
in place.
a
































































1/4" Nutdriver
































c
Replace the clips removed in
step “a” to secure the side
firebacks..
e
d
NOTE: Place the fireback
so the vertical grout line on
the edge of the fireback is
facing the rear.
Loosen this screw and slide the bracket up. Place the floor
firebacks in place (under the bracket). Slide the bracket
down and tighten the screw to secure the firebacks.
b
Due to the construction of the ceramic firebacks, you may need to re-position the
firebacks to achieve correct alignment.
4. Restore the fireplace to the correct configuration.