FireplaceXtrordinair 564 Series User manual

564 Artisan, MetalSmith Face Inst.
Artisan Charcoal 95400418 Artisan Patina Bronze 95400417
MetalSmith Patina Carbon: 95400440
Page 1 of 4 17601473 - 4/1/19 © Travis Industries, Inc.
Compatibility:
• 564 Fireplaces (SS, 25K, HO, E, etc.)
(all except CleanFace version)
Packing List:
• Face
• (4) 8-32 Nuts
• (2) 564 SS Top Brackets (w screws)
• (2) 10-24 1-1/2" Screws
The FPX Face Upgrade Kit (98500683) must
be installed prior to installing the facing
material and face.
The center deflectors must be in place when using this face to prevent
the facing above the fireplace from becoming too hot. If this face is
replacing a Lopi Grill (96200801), make sure to replace the center
deflectors.
Hand-Rubbed Patina Finishes
The optional patina finish is hand applied by a skilled artisan to permanently alter the metal colors and texture
of the face. Each face is individually hand-polished and fired in an oven which imparts unique color subtleties
with no two finishes alike. The patina finish on your face is a “living” color and will age and antique over time.
Enjoy the timeless, rich luster of your beautiful new face.
Installation Details – 564 SS, DF, HO
NOTE FOR THICK FACING (BRICK,
ROCK, ETC.):
The Fireplace Xtrodinair 564 Set-Up
Face is recommended for masonry
installation (98500674). The set-up face
helps locate and support the masonry
during installation.
SIDE OF FIREPLACE
1”
5/16” TO 1”
NOTE:
This face has an adjustable bracket that allows for
different facing depths to be tucked under the face.












36”
61”Radius
29”
2-3/4”

564 Artisan, MetalSmith Face Inst.
Artisan Charcoal 95400418 Artisan Patina Bronze 95400417
MetalSmith Patina Carbon: 95400440
Page 2 of 4 17601473 - 4/1/19 © Travis Industries, Inc.
Installation
1 Remove the glass barrier screen (see owner's manual for details). Secure the arch cover to the barrier
following the directions below (arch cover is shipped with the fireplace). Replace the glass barrier.
Lift the barrier up, pivot the top forward,
and remove from the fireplace.
Arch Cover Bend the tabs over to
secure the arch cover to
the barrier.

564 Artisan, MetalSmith Face Inst.
Artisan Charcoal 95400418 Artisan Patina Bronze 95400417
MetalSmith Patina Carbon: 95400440
Page 3 of 4 17601473 - 4/1/19 © Travis Industries, Inc.
Installation (continued)
2 The facing and hearth (if applicable) must be installed prior to attaching the face. See the installation
manual for complete details.
Raised
Fireplaces





























































Note how the tile is 1”
(maximum) above the
base of the fireplace.






















































Maximum 1`” Hearth
Floor-Level
Fireplaces






564 Artisan, MetalSmith Face Inst.
Artisan Charcoal 95400418 Artisan Patina Bronze 95400417
MetalSmith Patina Carbon: 95400440
Page 4 of 4 17601473 - 4/1/19 © Travis Industries, Inc.
Installation (continued)
3 Install the face following the directions below.



























































Attach the upper brackets
to the face with the
included nuts.
Slide the face into place. The
tabs on the upper brackets insert
into the slots on the fireplace
brackets, holding the face in place
while the screws are tightened.
a
b
cThe face is secured to the fireplace
with four screws. Two of the screws
are fastened to the upper brackets
with press nuts. The lower screws
are included with the face.