Firesense Woodberry 63688 User manual

7
7
WARNING
Before returning to your retailer, our Florida-based customer service team is available to help:
866
10112021
(/(&7521,&,*1,7(5
5HTXLUHV$$$%DWWHU\QRWLQFOXGHG
Woodberry Round Aluminum LPG Fire Pit .YJR63688

B
A
C
D
E
H
F
G
J
K
Q
PO
M N R
E
D
K
A
B
C
G
J





Stud (8x30mm)
Qty: 5
(4 for assy. +1 extra)
Washer/Spring
Washer/Nut (8mm)
Qty: 5
(4 for assy. +1 extra)
Stud (6x40mm)
Qty: 13
(12 for assy. +1 extra)
Bolt (6x16mm)
Qty: 4
(3 for assy. +1 extra)
Washer (M6)
Qty: 16
(15 for assy. +1 extra)
Spring Washer (M6)
Qty: 13
(12 for assy. +1 extra)
S
Nut (6mm)
Qty: 13
(12 for assy. +1 extra)
T
Plastic Cap (M8)
Qty: 4
U
Screwdriver
Qty: 1
V
Wrench
Qty: 1
W
Hex Wrench
Qty: 1
Z
Spare Adjustable Foot
Qty: 1

7

1Assemble the fire pit base: Locate Door PanelD, 3 Side
Panels E, Door Frame Leg F, and 2 Support Legs G.
Screw Studs Ointo the holes in the sides of all four Legs,
including the leg pre-assembled to the door.
Beginning with Door Frame Leg F join the Legs and Panels
together by fitting the holes on the sides of the Side Panels onto
the Studs installed earlier.
To secure the Legs to the Panels, place a Washer Q, then a
Spring Washer Ronto each Stud, then thread a Nut Sonto
each Stud. Do not tighten the hardware until the entire base is
assembled. Then,firmly tighten all Nuts with the Wrench V,
but DO NOT OVERTIGHTEN.







3ZY
1JL
5FSJQX
8UWNSL
<FXMJW
<FXMJW

6
2
3
Hardware Used:
Once all panels are bolted together,turn the table base
upside-down,then attach Tank Support Bar to Leg F/Gby
aligning the holes at each end of Tank Support Bar with the
holes at the bottom of each Leg.
Insert Bolt Pthrough Washer Qthen into holes.Tighten gently
with Hex Wrench W. Then attach Tank Support Ring to the leg
of Door Panel Dby aligning the hole in front of Tank Support
Ring with the hole in the leg.
Insert Bolt Pthrough Washer Qand then into the hole. Tighten
with Hex Wrench W.
Place Table Top Cso underside faces up. Screw 4 Studs Minto
the holes on the Table Top using Screwdriver U.
Then carefully turn the assembled fire pit base upside-down
and align the holes in the top of the Legs with the Studs
in the Table Top.
Place the holes over the Studs and secure each with Washer/
Spring Washer/Nut Nas illustrated.
Tighten with Wrench V. Then place Plastic Caps T over Nuts.
3

&
2
G

5Fire Glass Burner
Removable Burner
Cover Burner.
4
9FSP&HHJXX)TTW
'ZWSJW(TSYWTQ
HTSYWTQXXMTZQI
KFHJITTWWTYFYJI
YT\FWIQJKYXNIJ
TKTUJSNSL
4
5

-

6
6
6Connect hose and regulator to cylinder. The propane gas and
cylinder are sold separately. Use a standard 20lb propane cylinder
have this book.
Storage of an appliance indoors is permissible only if the cylinder is
disconnected and removed from the appliance. A cylinder must be
stored outdoors in a well-ventilated area out of the reach of children. A
disconnected cylinder must have dust caps tightly installed and must not
be stored in a building, garage or any other enclosed area. The maximum
inlet gas supply pressure: 250 , the minimum inlet gas supply
pressure: 5 .
for automatic operation at ratings less than full input rating. The pressure
regulator and hose assembly supplied with the appliance must be used.
The installation must conform with local codes, or in the absence of local
codes, with national fuel gas code, ANSI Z223.1/NFPA54, natural gas and
propane Installation Code, CSA B 149.1, or propane storage and handling
code, B149.2.
6

is at hose/