Firgelli UTVL-200 Series User manual

www.rgelliauto.com sales@rgelliauto.com
UTVL - 200 Series
DROP DOWN TV LIFT

www.rgelliauto.com sales@rgelliauto.com
Cauon
page 1

www.rgelliauto.com sales@rgelliauto.com
Model FA-UTVL-200-30 FA-UTVL-200-40 FA-UTVL-200-50
Retracted Length 39 inches 49 inches 59 inches
Stroke 30 inches 40 inches 50 inches
Recommended TV Size up to 30” tall up to 40” tall up to 40” tall
Input Voltage 110 volt AC / 60H
Output Voltage 24 volt DC, Max 50 VA
Input Current 1 amp
IP Rating 43
Operational Temperature -15°F to 150°F (-26°C to 65°C)
Duty Cycle 10% max, 2 min. on, 10 min. o󰀨
Load Capacity 120 lbs.
Depth 4 3/8 inches
Noise 5 dB
Speed 0.8 inches per second
Limit Switch Built in, includes external micro switch
Control Options RF Wireless Remote and Wired
Specicaons
page 2

www.rgelliauto.com sales@rgelliauto.com
Components
Track Linear Actuator
x 1
Main Long Bracket
x 1
L Brackets
x 2
T Bracket
x 1
Small TV Brackets
x 4
Long TV Support Arms 30”
x 2
Drywall Bracket
x 1
Long TV Support Arms 36”
x 2
Control Box
x 1
Wireless Remote
x 2
Limit Switch
x 1
Rocker Switch
x 1
Hardware
Bag Name Quanty
Screws for Drywall Phillips Countersunk
Screws M5 x 10
4
Flat Washer M6 4
Nut M5 4
Hex Bolt M8 x 12 4
Nut M8 4
Screws for Sliders and
TV Mounng Bars
Phillips Countersunk
Screws M5 x 8
4
Hex Bolt M8 x 10 4
Buery Wing Nut
Screw M5 x 9
4
Mounng Accessories
for TV Bracket
Hex Bolt M10 x 25 2
Flat Washer M11 2
Locking Washer M11 2
Hex Bolt M6 4
Flat Washer M6 4
Locking Washer M6 4
End Mounng Parts Clevis Pin 1
Coer Pin 1
page 3

www.rgelliauto.com sales@rgelliauto.com
1. Aach the Small TV Brackets (4) to the back of your television using the four M5 x 8 Phillips
Countersunk Screws. Please be aware that the sup-
plied screws may not t your television. Ensure that
you have the appropriate TV mounng screws before
connuing. Tighten unl secure.
2.Aach the Long TV Support Arms (2) to the Main Long Bracket using the four M8
x 10 Hex Bolts. Choose the 30” or 36” arms
depending on the width of your TV. Measure
and space the arms so the TV can slide on us-
ing the TV brackets from step 1. Tighten unl
secure.
3.Slide the L Brackets (2) through the slots on the Drywall Bracket and aach using the four
M5 x 10 Phllips Countersunk Screws, M6 Washers,
and M5 Nuts. Tighten unl secure.
4. Aach the assembled Drywall Bracket to the Main Long Bracket using the four
M8 x 12 Hex Bolts and M8 Nuts. Note that the
Drywall Bracket can be aached to either side
of the Main Bracket. Tighten unl secure.
Assembly Instrucons
page 4

www.rgelliauto.com sales@rgelliauto.com
5. Aach the “T”Bracket to the top end of the Track Actuator using the Clevis Pin and secure
it with the Coer Pin.
6. The Track Actuator may now be mount- ed to your installaon using the top
“T”Bracket and the aached bracket at the
boom of the actuator. Ensure the posion of
the actuator allows for the correct t of the TV
and the drywall bracket. Screws are not provid-
ed for this step. Use the appropriate hardware
for your installaon.
7. Plug in the actuator to the Control Box and extend the actuator. Mount the assembled
Main Long Bracket to the sliding carriage on the
Track Actuator using the four M6 x 25 Hex Bolts, M6
Locking Washers and M6 Washers for the smaller
holes on the outside and the two M10 x 25 Hex
Bolts, M11 Locking Washers, and M11 Washers for
the middle holes. Install all of the bolts before ght-
ening to ensure proper alignment.
8. Now that the Drop Down TV Li is assembled you can aach your TV to
the li. Slide the TV Mounng Brackets onto
the TV Long Arms and secure using the four M5
x 9 Buery Wing Nut Screws. Tighten unl
secure.
page 5

9. Program the Wireless Remote by pressing and holding the reset buon on the side of the
Control Box. While the reset buon is held press
either the up or down buon on the wireless remote
once. Release the reset buon and the Wireless
Remote is ready for use.
10.The Wireless Remote can be used for non-momentary operaon. Press the
up buon once to move the li up and press the
up or down buon to stop the li at any me.
Press the down buon once to move the li
down and press the down or up buon to stop
it.
11.
For momentary control use the oponal
Rocker Switch. Plug it into the Control Box
and hold “2” on the Rocker Switch to move the li
up and hold “1” to move the li down.
www.rgelliauto.com sales@rgelliauto.com
12.
To stop the TV li from retracng fur-
ther than desired you may install the
External Limit Switch. This step is completely
oponal and does not need to be completed in
order for the TV li to operate. The Limit Switch
stops the li from moving once it is pressed.
Plug the Limit Switch into the Control Box and
then install it so it will be pressed while the li is
moving up and right before the Drywall Bracket
touches the ceiling. You may need to make a
bracket to screw the Limit Switch to.
page 6