Firstech DC3 User manual

REVISION DATE
20220113
DOCUMENT NUMBER
Patent No. US 8,856,780 CA 2759622
TERMS OF USE
Automotive Data Solutions Inc. (“ADS”) products are strictly intended for installation by Certified Technicians who are
employed by a registered business specialized in the installation of automotive aftermarket electronics products. Prior
to beginning installation of an ADS product in a vehicle, it is the Certified Technician’s responsibility to review the most
current Product Guide, Install Guide and vehicle-specific notes available in Weblink®. ADS is not responsible for any
damages whatsoever, including but not limited to any consequential damages, incidental damages, damages for loss
of time, loss of earnings, loss of profit, commercial loss, loss of economic opportunity and the like that may or may not
have resulted from the use, misuse, improper installation or operation of its products. ADS reserves itself the right to
suspend any Weblink® account without notice and decline to offer technical support to non-Certified Technicians, non-
compliant Certified Technicians or end users.
PRODUCT GUIDE
DC3
www.idatalink.comAutomotive Data Solutions Inc. © 2022

Patent No. US 8,856,780 CA 2759622 DC3 Product Guide
GETTING STARTED - 1 OF 1
TABLE OF CONTENTS
DC3 Product Guide
Module Layout 3
Tach Programming Procedure 4
Module Diagnostics 5-6
Remote Starter Error Codes 7
Alarm Error Codes 8
Module Reset Procedure 9
Installation Checklist 10-11
Compatible Accessories 12-13
Remote Programming Procedure 14
Valet Mode Programming Procedure 15
WELCOME
Congratulations on the purchase of your DC3
solution. You are now a few simple steps away
from enjoying your new remote starter unit with
enhanced features.
Before starting your installation, please ensure that
your DC3 module is programmed with the correct
firmware for your vehicle and that you carefully
review the install guide.
NEED HELP?
1 866 427-2999
[email protected]
idatalink.com/support
www.12voltdata.com/forum
www.facebook.com/groups/idatatech
www.idatalink.comAutomotive Data Solutions Inc. © 2022 DC3
PAGE 2 OF 15
• 20220113

Patent No. US 8,856,780 CA 2759622 DC3 Product Guide
CONNECTOR PINOUT
M5
M6
M4
M3
M2
M1
4
5
3
2
1
6
M6
FUNCTIONS DEFINED BY FIRMWARE
AUTOMATIC
TRANSMISSION
CUT LOOP
MODULE CONNECTORS
FT-DAS - 4 PIN RED
BLE - 4 PIN YELLOW
RF PORT - 4 PIN BLUE
DRONE - 4 PIN GRAY
M6 - 6 PIN BLACK
PROGRAMMING BUTTON
M2 - 12 PIN BLACK
M3 - 10 PIN WHITE
LED 1 (BYPASS)
LED 2 (RS)
FT-DAS SENSITIVTY ADJUSTMENT DIAL
WEBLINK PORT - 4 PIN BLACK
MODULE
CM-DC3
7
9
3
10
8
6
4
1
2
5
7
9
3
10
8
11
12
6
4
1
2
5
7
9
3
10
8
11
13
14
12
15
17
18
19
20
16
6
4
1
2
5
4
5
3
2
1
6
M5
M4
01 GREEN•BLACK DOT - LOCK (-) OUTPUT
01 GREEN•BLACK DOT - LOCK (-) OUTPUT
02 BLUE•BLACK DOT - UNLOCK (-) OUTPUT
02 BLUE•BLACK DOT - UNLOCK (-) OUTPUT
03 RED/WHITE•BLACK DOT - TRUNK RELEASE (-) OUTPUT
03 RED/WHITE•BLACK DOT - TRUNK RELEASE (-) OUTPUT
04 GREEN/WHITE•BLACK DOT - ARM (-) OUTPUT
04 GREEN/WHITE•BLACK DOT - ARM (-) OUTPUT
05 GREEN/BLACK•BLACK DOT - DISARM (-) OUTPUT
05 GREEN/BLACK•BLACK DOT - DISARM (-) OUTPUT
06 BLUE/WHITE•BLACK DOT - GWR (-) OUTPUT
06 BLUE/WHITE•BLACK DOT - GWR (-) OUTPUT
07 BROWN•BLACK DOT - SIREN (+) OUTPUT
07 BROWN•BLACK DOT - SIREN (+) OUTPUT
08 WHITE/PURPLE•BLACK DOT - POC 1 - 2ND UNLOCK OTHER DOORS (-) OUTPUT
08 WHITE/PURPLE•BLACK DOT - POC 1 - 2ND UNLOCK OTHER DOORS (-) OUTPUT
09 PURPLE/BLACK•BLACK DOT - POC 2 - RAP SHUTDOWN (-) OUTPUT
09 PURPLE/BLACK•BLACK DOT - POC 2 - RAP SHUTDOWN (-) OUTPUT
10 WHITE/BLACK•BLACK DOT - POC 3 - HORN (-) OUTPUT
10 WHITE/BLACK•BLACK DOT - POC 3 - HORN (-) OUTPUT
11 BROWN/BLACK•BLACK DOT - POC 4 - STARTER KILL (-) OUTPUT
11 BROWN/BLACK•BLACK DOT - POC 4 - STARTER KILL (-) OUTPUT
12 WHITE•BLACK DOT - PARKING LIGHTS (-) OUTPUT
01 BROWN•SILVER DOT - BRAKE (+) INPUT
02 BLACK/WHITE•SILVER DOT - E-BRAKE (-) INPUT
03 PURPLE•SILVER DOT - DOOR (+) INPUT
04 GREEN•SILVER DOT - DOOR (-) INPUT
05 PURPLE/WHITE•SILVER DOT - TACH (-) INPUT
06 WHITE/BLUE•SILVER DOT - X-TRIGGER (-) INPUT
07 GRAY•SILVER DOT - HOOD (-) INPUT
08 BLUE•SILVER DOT - TRUNK (-) INPUT
09 GRAY/BLACK•SILVER DOT - GLOW PLUG (+) INPUT
10 TAN•SILVER DOT - EXT ALARM SENSOR (-) INPUT
FUNCTIONS DEFINED BY FIRMWARE
FUNCTIONS DEFINED BY FIRMWARE
M3
M2
RPS SENSOR - 4 PIN WHITE
SENSOR 2 - 4 PIN GREEN
ALARM LED - 2 PIN WHITE
TEMP SENSOR - 2 PIN BLUE
BATTERY - 2 PIN WHITE M5 - 6 PIN BLUE
M4 - 20 PIN BLACK
MODULE LAYOUT - 1 OF 1
M1
4
2
8
1
3
5
7
6
01 ORANGE - ACCESSORY (+)
01 ORANGE - ACCESSORY (+)
02 RED - POWER (30A)
02 RED - POWER (30A)
03 PURPLE - STARTER (+)
03 PURPLE - STARTER (+)
04 PINK/WHITE - PROG. RELAY #4 - IGNITION 2 (+) (DEFAULT)
04 PINK/WHITE - PROG. RELAY #4 - IGNITION 2 (+) (DEFAULT)
05 PINK - IGNITION (+)
05 PINK - IGNITION (+)
07 RED - POWER (30A)
07 RED - POWER (30A)
08 BLACK - GROUND
08 BLACK - GROUND
M1
06 WHITE - PROG. RELAY #5 (10A) - PARKING LIGHTS (+) (DEFAULT)
06 WHITE - PROG. RELAY #5 (10A) - PARKING LIGHTS (+) (DEFAULT)
M1 - 8 PIN BLACK
CONNECTOR PINOUT
www.idatalink.comAutomotive Data Solutions Inc. © 2022 DC3
PAGE 3 OF 15
• 20220113

Patent No. US 8,856,780 CA 2759622 DC3 Product Guide
01
ENGINE
START
STOP
OFF ACC ON STARTSTART
START
02
03
04
05
06
TACH PROGRAMMING PROCEDURE - 1 OF 1
START vehicle for 15 seconds.
Press and hold the brake pedal.
Press and release the module’s programming
button. (OR if the remotes are already
programmed to the vehicle, press and hold the
start button of the remote for 2.5 seconds.)
Wait, LED 2 will flash GREEN. (See the Module
Diagnostics page)
Release the brake pedal.
Module Programming Procedure completed.
www.idatalink.comAutomotive Data Solutions Inc. © 2022 DC3
PAGE 4 OF 15
• 20220113

Patent No. US 8,856,780 CA 2759622 DC3 Product Guide
MODULE DIAGNOSTICS - 1 OF 2
MODULE STATUS DURING: LED 2* LED 1** LED STATUS DIAGNOSTIC
MODULE PROGRAMMING
•Flashing RED Missing/wrong information from firmware or vehicle.
See firmware specific diagnostics, or contact technical support.
•Solid RED Module waiting for more vehicle information. Programming incomplete.
•Flashing GREEN Additional steps required to complete programming. Refer to install guide.
•Solid GREEN then OFF Module programming completed successfully.
oOFF No activity or module already programmed.
•1 RED flash No firmware on module. Connect to Weblink and flash device.
•2 ORANGE flashes Contact technical support.
•3 ORANGE flashes Module programming not completed.
•4 ORANGE flashes Contact technical support.
•7 ORANGE flashes Contact technical support.
•8 ORANGE flashes Loop not cut. Ensure loop is cut for automatic transmission. Reset and re-learn.
•9 ORANGE flashes Loop not cut. Ensure loop is cut for automatic transmission. Reset and re-learn.
•10 ORANGE flashes Boot loader update failed. Contact technical support.
•11 ORANGE flashes T-harness detection does not match install type selection in Weblink.
TACH PROGRAMMING
•Solid RED Tach learn in progress.
•1 GREEN flash Tach signal programmed in analog.
•2 GREEN flashes Tach signal programmed in data.
•3 RED flashes No tach signal detected
•4 RED flashes System is in valet mode. Turn off valet mode to program tach.
•6 RED flashes Engine sensing set for ‘assumed start’. No tach programming required.
•7 ORANGE flashes Engine sensing not configured properly. Contact technical support.
* LED 2 (RS) displays generic diagnostic codes specific to the remote start module. Orange LED flashes may appear red.
** LED 1 (Bypass) displays diagnostic codes specific to the firmware loaded on the module.
Visit the programming diagnostics page for more information.
www.idatalink.comAutomotive Data Solutions Inc. © 2022 DC3
PAGE 5 OF 15
• 20220113

Patent No. US 8,856,780 CA 2759622 DC3 Product Guide
MODULE DIAGNOSTICS - 2 OF 2
MODULE STATUS DURING: LED 2* LED 1** LED STATUS DIAGNOSTIC
REMOTE START SEQUENCE
•Flashing rapid RED Remote start shutdown sequence.
•Flashing slow RED Remote start shutdown error code. Contact technical support.
•Solid RED Remote start crank delay.
•Flashing rapid GREEN Remote start cycle in progress. Working correctly.
•1 GREEN flash Remote start initiated successfully.
•3 GREEN flashes Idle mode cycle in progress.
•4 GREEN flashes Turbo mode cycle in progress.
•Flashing GREEN Remote start cycle in progress. Displays vehicle platform during runtime.
•Rapid GREEN flashing Secure takeover initiated. Waiting to complete takeover after brake press.
TRANSMITTER PROGRAMMING
•Solid RED Remote programming in progress, waiting for remote pairing.
•1 GREEN flash Remote programmed.
•4 RED flashes Shutdown remote starter before attempting remote programming.
•5 RED flashes Engine must be off before attempting remote programming.
•6 RED flashes System must be unlocked/disarmed before attempting remote programming.
•7 RED flashes Module must be learned to the vehicle before attempting remote programming.
* LED 2 (RS) displays generic diagnostic codes specific to the remote start module. Orange LED flashes may appear red.
** LED 1 (Bypass) displays diagnostic codes specific to the firmware loaded on the module.
Visit the programming diagnostics page for more information.
www.idatalink.comAutomotive Data Solutions Inc. © 2022 DC3
PAGE 6 OF 15
• 20220113

Patent No. US 8,856,780 CA 2759622 DC3 Product Guide
REMOTE STARTER ERROR CODES - 1 OF 1
REMOTE STARTER ERROR CODES: NOTES PARKING LIGHT FLASHES DIAGNOSTIC
I WARNING: The following applies only when the parking lights are
connected and supported by the system.
3 + 1 Tach is not programmed OR engine is already running.
3 + 2 Key is in ignition ON position.
3 + 3 Door is open.
II After a remote starter failure, the parking lights will fl ash three [3x]
times followed by the error code. See table.
3 + 4 Trunk is open.
3 + 5 Foot brake is ON.
3 + 6 Hood is open.
3 + 7 Loop is not cut.
3 + 8 No tach detected.
3 + 9 Vehicle movement detected (VSS).
3 + 10 System is in Valet Mode.
3 + 11 CAN communication failure
3 + 12 RS not synchronized. Start vehicle with OEM key for 15 sec before trying a new RS sequence.
3 + 13 Bypass problem.
3 + 14 Idle mode or takeover is not available on this vehicle.
3 + 15 Overheat protection.
REMOTE STARTER SHUTDOWN ERROR CODES: NOTES PARKING LIGHT FLASHES DIAGNOSTIC
I WARNING: The following applies only when the parking lights are
connected and supported by the system.
4 + 1 Engine tach signal was lost.
4 + 2 Emergency brake signal was lost.
4 + 3 Foot brake ON detected.
II If the engine shuts down after a remote starter sequence
use the query command from a compatible aftermarket
remote to display the shutdown error code. The parking lights will
flash four [4x] times followed by the error code. See table.
4 + 4 Hood open detected.
4 + 5 Tach over rev detected.
4 + 6 Glow plug timeout error.
4 + 7 Vehicle movement detected (VSS).
4 + 8 Check engine light ON.
4 + 9 Low fuel level.
4 + 10 Open door detected.
4 + 11 CAN communication failure during RS sequence.
4 + 12 RS not synchronized. Start vehicle with OEM key for 15 sec before trying a new RS sequence.
4 + 13 Bypass problem.
4 + 14 Idle mode or takeover is not available on this vehicle.
4 + 15 Overheat protection.
www.idatalink.comAutomotive Data Solutions Inc. © 2022 DC3
PAGE 7 OF 15
• 20220113

Patent No. US 8,856,780 CA 2759622 DC3 Product Guide
ALARM ERROR CODES - 1 OF 1
ALARM ERROR CODES: NOTES PARKING LIGHT FLASHES ANTENNA LED FLASHES DIAGNOSTIC
I WARNING: The following applies only when the parking lights are
connected and supported by the system.
5 + 1 1 Shock sensor triggered
5 + 2 2 Door open
5 + 3 3 Trunk open
II If the alarm has been triggered, the parking lights will fl ash
fi ve [5x] times followed by the alarm activation event.
5 + 4 4 Hood open
5 + 5 5 Zone 2 input triggered
5 + 6 6 Foot brake ON
III The alarm event code is also displayed in a repeating pattern
on the antenna’s LED when the alarm is triggered, until unlock
is received.
5 + 7 7 Ignition ON
5 + 8 8 Motion detected
5 + 9 9 Tilt detected
5 + 10 10 Warn away input triggered
www.idatalink.comAutomotive Data Solutions Inc. © 2022 DC3
PAGE 8 OF 15
• 20220113

Patent No. US 8,856,780 CA 2759622 DC3 Product Guide
>>
01
02
03
04
05
06
07
08
>>
MODULE RESET PROCEDURE - 1 OF 1
The following procedure resets the module
programming to the vehicle. It does not reset
any settings configured online.
Disconnect all connectors from module except
the M1 BLACK 8-pin connector and the M4
BLACK 20-pin connector.
Disconnect the M1 BLACK 8-pin connector
and the M4 BLACK 20-pin connector.
PRESS AND HOLD the module’s programming
button while connecting the M1 BLACK
8-pin connector and the M4 BLACK 20-pin
connector.
Wait, LED 1 will flash RED. RELEASE
programming button.
LED 1 will turn RED for 2 seconds.
Module RESET completed.
Reconnect all connectors.
Repeat programming procedure.
Failure to follow procedure may result with a
DTC or a CHECK ENGINE error message.
www.idatalink.comAutomotive Data Solutions Inc. © 2022 DC3
PAGE 9 OF 15
• 20220113

Patent No. US 8,856,780 CA 2759622 DC3 Product Guide
INSTALLATION CHECKLIST - 1 OF 2
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3Press the LOCK button once [1x] on the aftermarket keyfob.
¨
Question 1: Do the doors lock?
YES: Go to next step.
¨
NO: Verify the remote programming, the RF connections and the wired door lock/unlock
connections as illustrated in the wiring diagram, if applicable. Repeat the test and call
technical support, if the problem persists.
4Press the UNLOCK button once [1x] on the aftermarket keyfob.
¨
Question 2: Do the doors unlock?
YES: Go to next step.
¨
NO: Verify the remote programming, the RF connections and the wired door lock/unlock
connections as illustrated in the wiring diagram, if applicable. Repeat the test and call
technical support, if the problem persists.
5Press the TRUNK release button once [1x] on the aftermarket keyfob if supported.
¨
Question 3: Does the trunk or hatch open/unlock?
YES: Close trunk or hatch and go to next step.
¨
NO: Verify the remote programming, the RF connections and the wired trunk/hatch
connections as illustrated in the wiring diagram, if applicable. Repeat the test and call
technical support, if the problem persists.
6Press the AUX 1 button once [1x] on the aftermarket keyfob if supported.
¨
Question 4: Does the driver side sliding door open?
YES: Press the AUX 1 button once [1x] to close the driver sliding door and go to next step.
¨NO: Verify the remote programming and the RF connections. Repeat the test and call
technical support, if the problem persists.
7Press the AUX 2 button once [1x] on the aftermarket keyfob if supported.
¨
Question 5: Does the passenger side sliding door open?
YES: Press the AUX 2 button once [1x] to close the passenger sliding door and go to next step.
¨NO: Verify the remote programming and the RF connections. Repeat the test and call
technical support, if the problem persists.
8Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
¨
Question 6: Does the vehicle remote start?
YES: Go to next step.
¨NO: Verify the remote programming, the RF connections and check the remote start error
codes. Repeat the test and call technical support, if the problem persists.
9Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle.
¨
Question 7: Does the vehicle shut down?
YES: Go to next step.
¨NO: Repeat step. If problem persists, press the brake pedal once [1x] to shut down the vehicle
and call technical support.
10 RAP and auto light shutdown test
¨
Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after
remote start shutdown?
YES: Go to next step.
¨NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the
test and call technical support if the problem persists.
11 Open hood.
12 If not already installed, affi x the mandatory orange warning sticker under the hood and
proceed to next step.
13 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
¨
Question 9: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood
switch, then repeat the test.
¨NO: Go to next step.
14 Close hood.
15 Enter vehicle and close the doors.
16 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
17 Wait for the vehicle to start.
18 Press brake pedal.
¨
Question 10: Does the vehicle shut down?
YES: Go to next step.
¨
NO: The module does NOT detect the brake pedal signal. Press the START/STOP button once
[1x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the
wiring diagram, if applicable, and call technical support.
19 Exit vehicle.
20 Installation checklist completed.
CHECKLIST - WITH AFTERMARKET KEYFOB
www.idatalink.comAutomotive Data Solutions Inc. © 2022 DC3
PAGE 10 OF 15
• 20220113

Patent No. US 8,856,780 CA 2759622 DC3 Product Guide
INSTALLATION CHECKLIST - 2 OF 2
CHECKLIST - WITH OEM KEYFOB
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
¨
Question 1: Does the vehicle remote start?
YES: Go to next step.
¨NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists.
4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle.
¨
Question 2: Does the vehicle shut down?
YES: Go to next step.
¨NO: Repeat step. If the problem persists, press on the brake pedal once [1x] to shut down the vehicle and call technical support.
5 RAP Shutdown test
¨
Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
¨NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists.
6 Open hood.
7 If not already installed, affi x the mandatory orange warning sticker under the hood and proceed to next step.
8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
¨
Question 4: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
¨NO: Go to next step.
9 Close hood.
10 Enter vehicle and close the doors.
11 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
12 Wait for the vehicle to start.
13 Press brake pedal.
¨
¨
Question 5: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if
applicable, and call technical support.
14 Exit vehicle.
15 Installation checklist completed.
www.idatalink.comAutomotive Data Solutions Inc. © 2022 DC3
PAGE 11 OF 15
• 20220113

Patent No. US 8,856,780 CA 2759622 DC3 Product Guide
www.idatalink.comAutomotive Data Solutions Inc. © 2022 DC3
PAGE 12 OF 15
• 20220113
COMPATIBLE ACCESSORIES - 1 OF 2
MODULE
TELEMATIC PORT
DRONE
(NC)
TELEMATIC KIT (accessory sold separately)
10 11 12 13 14 15 16
12345678
9
WEBLINK MOBILE (accessory sold separately)
MOBILE DEVICE
PORT
OBDII CONNECTOR
4 PIN BLACK CABLE
MODULE
WEBLINK PORT
OBDII CONNECTOR
WEBLINK CABLE (required accessory sold separately)
WEBLINK CABLE
COMPUTER
USB PORT
4 PIN BLACK CABLE
MODULE
WEBLINK PORT

Patent No. US 8,856,780 CA 2759622 DC3 Product Guide
www.idatalink.comAutomotive Data Solutions Inc. © 2022 DC3
PAGE 13 OF 15
• 20220113
COMPATIBLE ACCESSORIES - 2 OF 2
RF KIT
RF KIT (accessories sold separately)
ANTENNA
MODULE
RF PORT
TEMPERATURE SENSOR
TEMPERATURE SENSOR (accessories sold separately)
MODULE
2 PIN BLUE
4
2
8
1
3
5
7
6
M1
MODULE
M1
ANALOG HARNESS FT-HRN-DC3-PWR (sold separately)
01 ORANGE - ACCESSORY (+)01 ORANGE - ACCESSORY (+)
02 RED - POWER (30A)
02 RED - POWER (30A)
03 PURPLE - STARTER (+)
03 PURPLE - STARTER (+)
04 PINK/WHITE - PROG. RELAY #4 - IGNITION 2 (+) (DEFAULT)
04 PINK/WHITE - PROG. RELAY #4 - IGNITION 2 (+) (DEFAULT)
05 PINK - IGNITION (+)
05 PINK - IGNITION (+)
07 RED - POWER (30A)
07 RED - POWER (30A)
08 BLACK - GROUND
08 BLACK - GROUND
06 WHITE - PROG. RELAY #5 (10A) - PARKING LIGHTS (+) (DEFAULT)
06 WHITE - PROG. RELAY #5 (10A) - PARKING LIGHTS (+) (DEFAULT)
07 BROWN•BLACK DOT - SIREN (+) OUTPUT RED
BLACK SIREN
ALARM LED
FT-DAS
MODULE
12 PIN BLACK
MODULE
2 PIN WHITE
MODULE
4 PIN RED
ALARM KIT (accessories sold separately)

Patent No. US 8,856,780 CA 2759622 DC3 Product Guide
>>
01
02
ENGINE
START
STOP
OFF ACC ON START
ON
03
04
05
06
>>
07
08
ENGINE
START
STOP
OFF ACC ON STARTOFF
09
AFTERMARKET REMOTE PROGRAMMING PROCEDURE - 1 OF 1
WARNING: Program aftermarket remotes
before usage. A maximum of four [4x]
aftermarket remotes per system.
Time restriction. Complete next step within 7
seconds.
Cycle ignition ON five times [5x OFF/ON]
rapidly.
Parking Light will flash once [1x].
Time restriction. Complete next step within 5
seconds from previous step.
Press once [1x] on LOCK button of aftermarket
remote.
Parking Light will flash once [1x].
To program additional remotes: repeat steps 4
to 6 using each additional remote.
Wait, Parking Light will flash twice [2x].
Turn ignition to OFF position.
Aftermarket Remote Programming Procedure
completed.
www.idatalink.comAutomotive Data Solutions Inc. © 2022 DC3
PAGE 14 OF 15
• 20220113

Patent No. US 8,856,780 CA 2759622 DC3 Product Guide
>>
01
02
ENGINE
START
STOP
OFF ACC ON START
ON
03
04
05
ENGINE
START
STOP
OFF ACC ON STARTOFF
06
>>
VALET MODE PROGRAMMING PROCEDURE - 1 OF 1
NOTE: In Valet Mode, the Remote starter is not
functional. Keyless entry, Lock and Unlock will
remain functional. See RF kit user manual for
alternate valet mode programming.
Time restriction. Complete next step within 7
seconds.
Cycle ignition ON twice [2x OFF/ON] rapidly.
Press and release the BRAKE pedal three
times [3x].
Parking Light will flash once [1x] then will
flash twice [2x].
Set ignition to OFF position.
Valet Mode Programming Procedure
completed.
To exit valet mode: repeat steps 1 to 5.
www.idatalink.comAutomotive Data Solutions Inc. © 2022 DC3
PAGE 15 OF 15
• 20220113