Fisher & Paykel CI926DTB User manual

FULL SURFACE INDUCTION COOKTOP
CI926DTB model
INSTALLATION GUIDE
NZ AU BI EU SG

SAFETY AND WARNINGS
!WARNING!
Electric Shock Hazard
Failure to follow this advice may result in
electric shock or death.
• Disconnect the appliance from the mains
electricity supply before carrying out any work
or maintenance.
• Connection to a good earth wiring system is
essential and mandatory.
• Alterations to the domestic wiring system must
only be made by a qualified electrician.
! WARNING!
Cut Hazard
Failure to use caution could result in injury.
• Take care: some edges are sharp.
READ AND SAVE THIS GUIDE
General Use
zRead these instructions carefully before installing this product.
zSave these instructions for the local electrical inspector’s use.
zInstallation must comply with your local building and local electricity regulations.
zThis appliance is to be installed and serviced only by Fisher & Paykel trained and supported
service technician or qualified person.
zThe manufacturer accepts no responsibility for the incorrect installation of appliances.
Incorrect installation may result in personal injury, damage to property and may invalidate
any warranty or liability claims.
zDo not modify this appliance.
zDo not use or store flammable materials on or near this appliance.
zPacking elements (eg plastic bags, polystyrene foam, staples, packing straps etc) and tools
should not be left around during and after installation, especially if they are within easy
reach of children, as these may cause serious injuries.
zMake sure you recycle the packaging material.
zBefore disposing of any appliance, make sure that it can no longer be used and that all
hazardous parts are removed or made harmless, so that children playing with the old
appliance cannot harm themselves.
zOnly genuine replacement parts may be used for servicing the appliance. These are
available from your nearest Fisher & Paykel Service Center.
zThis cooktop must be connected to the mains power supply only by a suitably
qualified person.
zDO NOT use adapters, reducers, or branching devices when connecting the cooktop to the
mains power supply to prevent overheating and fire.
zThe power supply cable must not touch any hot parts and must be positioned so that its
temperature will not exceed 75°C at any point.
zThis cooktop requires adequate supply of cool air to fully function. The base of the cooktop
must have direct unrestricted ventilation to the room where the cooktop is installed. There
must be a 4mm air gap at the front of the cooktop. (See ‘Venting Clearances’ page)
3

INSTALLATION CONSIDERATIONS
Before installation, please ensure the following:
zA suitable disconnection switch is incorporated in the permanent wiring, mounted and
positioned to comply with the local wiring rules and regulations. A means of disconnection
with at least a 3 mm air gap contact separation in all poles must be incorporated into
the fixed wiring in accordance with the wiring rules, unless the local wiring rules allow for
alternative means.
zThe benchtop is made of a heat resistant material.
zThe power supply cable is not accessible through cupboard doors or drawers.
zThere is adequate flow of cool air from the cabinetry to the base of the cooktop. You
may ventilate from adjacent cupboards, but ensure that the available air supply will not
be restricted.
zThe ventilation area must be at least 50mm diameter holes or of equivalent area.
zThe isolating switch is easily accessible by the customer.
zUse heat-resistant and easy-to-clean finishes (such as ceramic tiles) for the wall surfaces
surrounding the cooktop.
zDO NOT install the cooktop directly above a dishwasher, fridge, freezer, washing machine or
clothes dryer, as the humidity may damage the cooktop electronics.
zIf the cooktop is installed above an oven, ensure the oven has a built-in cooling fan.
zEnsure the installation complies with all clearance requirements and applicable standards
and regulations.
zConsult your local building authorities and by-laws if in doubt regarding the installation.
zTo eliminate the risk of burns or fire by reaching over heated surface units, cabinet storage
space located above the surface units should be avoided. If cabinet storage is to be
provided, the risk can be reduced by installing a rangehood that projects horizontally a
minimum of 127mm beyond the bottom of the overhead cabinets.
During installation, please ensure the following:
zSeal the exposed bare edges of the cutout with an oil-based paint or moisture-proof
polyurethane to prevent possible moisture creeping between the cooktop trim and
the benchtop.
zTake extreme care not to chip, crack, or break the top glass surfaces during installation.
A heavy metal tool or part accidentally dropped on the glass could damage it.
zIf, after following the instructions given, correct performance cannot be achieved, please
contact your nearest Fisher & Paykel Service Centre, Customer Care, or contact us through
our local website listed at the end of this document.
IMPORTANT!
The owner carries all risk for flush mounting the cooktop. Fisher & Paykel will not be liable
for any costs associated with removing or replacing a flush-mounted and/or sealed-in
product, nor for repairing any damage that may be incurred by doing this.
Ensure the installation layout allows access to the cooktop from underneath to avoid cutting
out the silicone when servicing.
COMPONENTS
BEFORE INSTALLATION PARTS SUPPLIED
TOOLS REQUIRED
RouterSilicone Cutter
Foam tape (1)
4

PRODUCT DIMENSIONS
CI926DTB
MM
A Overall height of cooktop 52
B Overall width of cooktop 920
C Overall depth of cooktop 530
D Height of chassis* 48
E Width of chassis 884
F Depth of chassis 479
G Height of cooktop glass 4
H Depth of front overhang of cooktop glass 16
I Depth of rear overhang of cooktop glass 35
J Depth of side overhang of cooktop glass 18
K Distance of power connector from right side of
chassis 120
L Distance of power connector from rear of
chassis 50
* Includes power plug
PRODUCT DIMENSIONS
Actual product dimension may vary by ± 2 mm.
PLAN
B
C
FRONT
A
E
KL
B
G
J
J
PROFILE
F
H I
D
ISOMETRIC
5

CUTOUT DIMENSIONS
CUTOUT DIMENSIONS
CI926DTB
MM
A Overall width of cutout 890
B Overall depth of cutout 485
C Corner radius of cutout max 10
PROUD INSTALLATION FLUSH INSTALLATION
FRONT
PLAN
B
A
C
CUTOUT DIMENSIONS
CI926DTB
MM
A Overall width of routered recess 925
B Overall depth of routered recess 535
C Offset overhang allowance 35
D Height of routered recess 5
E Width of cutout 890
F Depth of cutout 485
G Corner radius of routered recess 4.5
H Corner radius of cutout max 10
FRONT
PLAN
fb
e
A
H
G
C
D
6

CLEARANCE DIMENSIONS
CLEARANCE DIMENSIONS
CI926DTB
MM
A Minimum clearance from glass surface to rangehood 650
B Minimum clearance below top of countertop to top of any appliance,
companion product or obstruction below cooktop 65
C Minimum clearance from side edges of cutout to nearest
combustible surface 30
D Maximum distance from right edge of cutout to center of junction box 762
E Minimum clearance below top of countertop to junction box 230
F Minimum clearance from countertop to overhead cabinet
(not directly above wwthe cooktop) 450
G Maximum depth of overhead cabinetry 330
H Minimum distance between overhead cabinets
(centered above the cooktop) 920
I Minimum clearance from rear edge of cutout to nearest
combustible surface 45
J Minimum clearance from front edge of cutout to front edge of counter 35
H
A
BED
F F
G
C
I
J
C
7

VENTING CLEARANCES
Oven* with cooling fanDrawer or other obstruction
This cooktop requires adequate supply of cool air to fully function. The base of the cooktop
must have direct unrestricted ventilation to the room where the cooktop is installed. There
must be a 4mm air gap at the front of the cooktop.
CLEARANCE DIMENSIONS MM
A Minimum ventiliation gap at the front of the cooktop 4
B Minimum clearance below top of countertop to top of any appliance,
companion product or obstruction below cooktop 65
C Minimum ventiliation gap at the rear of the cooktop 20
D Minimum diameter of cooling air hole 50
CLEARANCE DIMENSIONS MM
A Minimum ventilation gap at the front of the cooktop 4
B Minimum ventilation gap at the rear of the cooktop 20
C Minimum diameter of cooling air hole 50
*Some ovens require installation in a sealed box. For ovens installed in the sealed box, the cooktop must be accessed from the
top when servicing. Please refer to your oven installation guide for more information.
A A
B
D C
C B
DRAWER OR OTHER OBSTRUCTION OVEN WITH COOLING FAN
8

PROUD INSTALLATION
4
Gently lower the cooktop into the
cutout ensuring you have access
below the countertop for future
servicing..
3
Trim the excess adhesive foam
tape using a sharp cutter or
trimmer knife.
Take care not to damage the
benchtop.
1Turn the cooktop upside down
on a protective cover.
2
Apply adhesive foam tape around
the glass overhang, 5mm from
the edge of the glass.
Ensure the adhesive side facing is
down to form a continuous seal
around the cooktop.
5mm
9

FLUSH INSTALLATION
1
Prepare the countertop for flush
installation. Use a router to cut
out the edges of the countertop
to specified depth (5mm).
Attach an adhesive foam tape
along the edges of the routered
recess.
Adhesive
foam tape
3
Mask off the area to be siliconed
with adhesive tape.
Ensure both the cooktop and
countertop are protected.
4
Apply silicone in the gap
between benchtop and cooktop.
Once the silicone dries, remove
the adhesive tape and wipe off
excess silicone.
Gently lower the cooktop into the
cutout ensuring you have access
below the countertop for future
servicing.
2
Ensure the installation layout allows access to the cooktop from underneath to avoid cutting
out the silicone when servicing.
10

ELECTRICAL CONNECTION
Before connecting the cooktop to the mains power supply check that:
zThe domestic wiring system is suitable for the power drawn by the cooktop.
zThe voltage corresponds to the value given in the rating plate.
zThe power supply cable sections can withstand the load specified on the rating plate.
MODEL MAX. CURRENT DRAW MAX. LOAD VOLTAGE
CI926DTB4
48A
3x16A 11100W 220 – 240V 1N ~
380 - 415V 3N ~
To suit the domestic electric power grid setup of your local market, contact your
Fisher & Paykel service technician to limit the maximum power consumption of your cooktop.
CI926DTB MODELSSPECIFICATION
Three-phase connection
Single-phase connection
PE
1
2
3
4
5
NL
PE
1
2
3
4
5
NL1L3L2
11

Complete and keep for safe reference:
Model
Serial No.
Purchase Date
Purchaser
Dealer Address
Installer’s Name
Installer’s Signature
Installation Company
Installation Date
INSTALLER CHECKLIST
TO BE COMPLETED BY THE INSTALLER
GENERAL ELECTRICAL
Read safety and warnings in the user guide before operating the cooktop.
Specified clearance maintained.
Unit is level – front to back and side to side.
All packaging materials have been removed.
There is constant flow of cool air from the cabinetry to the base of the cooktop.
Basic operation has been demonstrated to the customer.
The cooktop is functioning correctly. Turn on all of them to a high setting and leave
them on for at least one minute.
Touch controls and displays are functioning.
Receptacle with correctly rated over-current protection is provided for service
cord connection.
Adequate ground connection.
Power supply cable is accessible and is not touching the cooktop.
12

59201A 0.21
FISHERPAYKEL.COM
© Fisher & Paykel Appliances 2021. All rights reserved.
The models shown in this guide may not be available in all markets
and are subject to change at any time.
The product specifications in this guide apply to the specific products and
models described at the date of issue. Under our policy of continuous product
improvement, these specifications may change at any time.
For current details about model and specification availability in your country,
please go to our website or contact your local Fisher&Paykel dealer.