Fisher & Paykel BI602 Series User manual

542065C 05.2005 NZ
Astro P
BI452
Installation Instructions
NZ, AU Installation Information
Astro E,
Astro X
BI602
Aeron A,
Aeron E
BI602
Astro Double
BI602
Astro Tower
BI602

1
BI452 Series
Compact Built-In Oven
BI602 Series
Single Built-In Oven
600 mm
20 mm
≥570 mm
20mm
564mm
315mm
435 mm
450 mm
595 mm
600 mm
20mm
564mm
460mm
580 mm
595 mm
595 mm
554 mm
554 mm
600mm
20 mm
≥570 mm
440 mm
585 mm
600mm
16-20 mm 16-20 mm

2
20 mm
≥570 mm
20mm
564mm
460mm
1062 mm
1077 mm
595 mm
554 mm
922 mm
20mm
564mm
460mm
917 mm
932 mm
595 mm
554 mm
315mm
600 mm
600mm
20 mm
≥570 mm
600 mm
16-20 mm 16-20 mm
BI602 Series
Double Built-In Oven
BI602 Series
Tower Built-In Oven
600mm
1067 mm

3
Warnings and Safety information
CAUTION!
In order to avoid hazard these products
must be installed according to these
instructions.
Please follow installation information
carefully. If in doubt consult your local
building authority by-laws.
Failure to install the product correctly
could invalidate any warranty or liability
claims.
The product is to be connected to the
electrical supply only by a suitably
registered electrical person.
IMPORTANT!
Please make this information available to
the person responsible for installing the
product as it could reduce your installation
costs.
The cavity must be a completely sealed
box with no gaps. This will ensure the
cooling air flows under the product and
through the oven frame to give the correct
venting and cooling for the oven and
cabinet surround. Failure to seal the cavity
box may cause distortion of surrounding
cabinetry.
Read these instructions carefully before
installing or using this product.
Before you start
Ensure a suitable disconnection switch
is incorporated in the permanent wiring,
mounted and positioned to comply with the
local wiring rules and regulations. The switch
must be of an approved type installed in
the fixed wiring and provide a 3 mm air gap
contact separation in all poles in accordance
with the local wiring rules.
In Australia and New Zealand, a switch of the
approved type with a 3 mm air gap must be
installed in the active (phase) conductor of
the fixed wiring.
Ensure that the location of the oven
connection socket (if fitted) is outside the
installation space if the product is flush to the
rear wall.
Ensure the electrician provides sufficient
free length of mains cable to reach from the
bottom rear of the cavity to at least 1.5 metres
in front of the bottom edge of the opening.
The cable may enter the cavity from the side,
top or bottom, but entry must be at the rear
of the cavity.
Ensure that the benchtop and oven cavity are
square and level.
Use easy-to-clean finishes for the wall surfaces
surrounding the oven and cooktop. This
will help to remove any staining caused by
cooking fumes.
Check that the height of the product from the
floor suits the user.
Ensure that the oven door(s) will be clear of
obstructions when fully opened.
WARNING!
Cut Hazard
Take care - panel
edges are sharp.
Failure to use caution
could result in minor
injury or cuts.

4
Installation Instructions
Flush fitting installation options
D
C
B
20 mm
2.5 mm
20 mm
2.5 mm
20 mm
2.5 mm
CUPBOARD FRONT
DRAWER FRONT
Installation instructions
1 Check that the oven cavity is square and
within the limits specified.
2 Remove the mains wiring access cover.
3 Connect the mains wiring and refit the
access cover.
4 Remove the oven door and accessories and
slide the oven into place. Centre the oven
in the cavity, leaving a space of 2.5 mm on
each side between the door edge and the
joinery.
5 Use the four ‘wood screws’ and washers
supplied to secure the oven to the cavity,
through the holes in the oven frame. See the
flush fitting installation options.
6 Test the oven then refit the door and
accessories. Check that the oven is firmly
secured in the oven cavity.
Installing a cooktop above the
oven
If installing a cooktop above the oven ensure
adequate clearance is provided for the
cooktop as per the cooktop manufacturer’s
instructions.

5
Notes

6
Notes