Fisher & Paykel DishDrawer DD605 Series User manual

WARNING!
Electrical hazard
Before installing the DishDrawer®, remove the house fuse or open the circuit breaker.
If permanently connecting the DishDrawer®, be sure the power is isolated and the DishDrawer® unplugged.
This appliance must be grounded. In the event of a malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This
appliance is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is installed and grounded in
accordance with all local codes and ordinances. Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service
representative if you are in doubt as to whether the appliance is properly grounded.
Do not modify the power supply plug provided with the appliance - if it will not fit the outlet, have a proper outlet installed by a qualified electrician. Do not use an extension cord, adapter plug or
multiple outlet box.
Failure to do so may result in electrical shock or death.
Important safety precautions!
Installation of this DishDrawer® requires basic mechanical and electrical skills.
Be sure to leave these Instructions with the Customer.
Installation must comply with your local building and electricity regulations.
At the completion of the DishDrawer® installation, the Installer must perform
Final Check List.
Remove all packaging materials supplied with the DishDrawer®.
This DishDrawer® is manufactured for indoor use only.
Ensure all water connections are turned OFF. It is the responsibility of the plumber and
electrician to ensure that each installation complies with all Codes and Regulations.
The DishDrawer® MUST be installed to allow for future removal from the enclosure if service is required.
DishDrawer®
Installation instructions
DD605 models US CA
Important!
SAVE THESE INSTRUCTIONS
The models shown in this document may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country, please go to our website www.
fisherpaykel.com or contact your local Fisher & Paykel dealer.
SAFETY AND WARNINGS
WARNING!
Cut hazard
Take care - panel edges are sharp.
Failure to use caution could result in injury or cuts.
30 mm
3
2
1
4
5
6
7
7
8
8
13
17
14
15
15
16
9
12
11
11
10
A
Ensure the drawer is removed
and then rotated counter-
clockwise to prevent kinked
hoses.
Before refitting the drawer,
ensure the hoses are not
twisted and the latches at
the rear of each drawer
runner are facing forward.
Ensure the drawer clips on
both sides are reset.
Ensure the drawer
is now rotated
clockwise back.
Remove knock-out for cable
clamp. Fit suitable cable clamp
for the conduit and terminate
the wiring as shown.
5 ⁄”
( 150 mm)
CD
Remove Power supply
B
1
O
B
C
E
D
F
G
H
J
N
P
I
Installation diagrams for illustration purposes only
K
L
M
A
N
G
C
I
Product dimensions (inches (mm))
Prenished
LCD
DD605
Prenished
Flat door
DD605
Integrated
DD605
Aoverall height* of product 32 ¼ - 34 ⁄”
(819.5- 879.5)
32 ¼ - 34 ⁄”
(819.5- 879.5)
32 ¼ - 34 ⁄”
(819.5- 879.5)
Boverall width of product 23 ⁄”(595) 23 ⁄”(595) 23 ⁄”(595)
Coverall depth of product (excl. curvature/handle) 22 ⁄” (570) 22 ⁄” (570) 22 ⁄” (570)
Ddepth of drawer (open) (excl. curvature/handle) 20 ⁄” (520) 20 ⁄” (520) 20 ⁄” (520)
Eheight* of chassis 31 ⁄” (809) 31 ⁄” (809) 31 ⁄” (809)
Fheight range of levelling feet 2 ⁄” (60) 2 ⁄” (60) 2 ⁄” (60)
Gdepth of chassis 21 ¾” (552) 21 ¾” (552) 21 ¾” (552)
Hdepth of drawer front panel (excl. curvature/handle) ⁄” (18) ⁄” (18) ⁄” (18)
Idepth of curvature or handle 1 ⁄” (30) ** n/a
Jdepth of kickstrip 2 - 4 ⁄” (50 - 110) 2 - 4 ⁄” (50 - 110) 2 ⁄ - 5”(67 - 127)***
Kheight of upper drawer front 15 ½” (394) 15 ⁄” (398) 15 ⁄” (398) min
Lheight of lower drawer front 13 ⁄” (351) 14” (356) 12 ¼” (311.5) min
Mheight of kickstrip (adjustable) 2 ¾ - 4 ¾” (70 - 120) 2 ¾ - 4 ¾” (70 - 120) 2 ¾ - 4 ¾” (70 - 120)
Nheight of installation tab slots (on top of chassis) ¾” (2) ¾” (2) ¾” (2)
Oheight of drawer fronts 29 ⁄” (751) 30 ⁄” (764) 28 ¼” (717.5) min
Pheight* of top of upper drawer to top of chassis ¼” (7) ¾” (2) n/a
* Chassis heights include tab slots *** Prenished 2 - 2 ½”(50-65 mm); Integrated 2 ⁄” (67 mm) less the
Kickstrip Panel thickness (Minimum Panel thickness using the
supplied screws is ⁄” (9 mm)).
** Designer handle - 1 ⁄”(41 mm)
Curved handle - 1 ⁄”(36 mm)
Cabinetry dimensions (inches (mm))
Prenished
LCD
DD605
Prenished
Flat door
DD605
Integrated
DD605
Ainside height of cavity 32 ⁄ - 34 ¾”
(820 - 882.5)
32 ⁄ - 34 ¾”
(820 - 882.5)
32 ⁄ - 34 ¾”
(820 - 882.5)
Binside width of cavity 23 ⁄” (600) 23 ⁄” (600) 23 ⁄” (600)
Cinside depth of cavity (inside) 22 ⁄” (580) 22 ⁄” (580) 22 ⁄” (580)
Dheight of adjacent cabinetry 28 ⁄” (720) 28 ⁄” (720) 28 ⁄” (720)
Eheight of kickstrip 2 ¾- 4 ¾” (70 - 120) 2 ¾- 4 ¾”(70 - 120) 2 ¾- 4 ¾” (70 - 120)
Minimum clearances (inches (mm))
⁄” (2.5 mm)
⁄” (2.5 mm)
A
B
C
D
E
Installation diagrams for illustration purposes only
½” (13 mm)
2
The switched power outlet must be outside the DishDrawer® cavity so that it is accessible after installation.
Care should be taken when the appliance is installed or removed to reduce the likelihood of damage to the
power supply cord.
If the DishDrawer® is to be relocated from one installation to another it must be kept upright to avoid
damage from water spillage.
Make sure only new hoses are used for connection (supplied with DishDrawer®). Old hoses should not be
reused.
Failure to install the DishDrawer® correctly could invalidate any warranty or liability claims.
If the product is installed in a motor vehicle, boat or similar mobile facility, you must bring the vehicle, boat
or mobile facility containing the product to the service shop at your expense or pay the service technician’s
travel to the location of the product.
PRODUCT AND CABINETRY DIMENSIONS OPTIONALLY HARD WIRING THE PRODUCT
5
2”x 4”
PARTS SUPPLIED
Clamp (1)
Wire clip (2) Phillips
16 mm
screws (9)
Drain hose
support (1) Moisture protection tape (1)
(to prevent moisture
damage)
Drain hose
joiner (1) Install
tabs (2) Prefinished toe kick (1)
White or Black
Washer (1) Edge Protector (1)
(if service hole
partition is metal)
If the Drain hose(s) supplied are not long enough to reach your services, you must use a Drain Hose Extension Kit P/N 525798 which will extend the drain hose(s) by 3.6m. The kit is available from the nearest Fisher & Paykel
Authorized Service Agent, or Toll free 1.888.936.7872 or www.fisherpaykel.com.
Hexagonal
socket (2)
(Long & Short)
Important!
Be sure the edges of the services hole are smooth or covered. If the services
hole is through a metal partition the hole must be protected with the Edge
Protector supplied to prevent damage to the power cord or hoses.
These marks indicate mounting tab screw locations
Preferred position. If adequate clearance, services hole can be
higher to clear toekick space.
If hole is higher, ensure drain hose(s) are routed straight into the
waste connection.
Note: Services can be located either side of DishDrawer®.

*
110-120 VAC
max. 15 A
Moisture protection
tape must be applied.
max. ø
1 ½”
(
38 mm)
**
min. 7 ⁄”
(
200 mm)
⁄”
( 10 mm)
max. 17 ⁄”
(
450 mm)
If no side partition, use a
brace for securing.
CAVITY PREPARATION
3
4
Water Pressure Max Min
Water softener models 1 MPa (145 psi) 0.1 MPa (14.5 psi)
Other models 1 MPa (145 psi) 0.03 MPa (4.3 psi)
Drains will need to be separated to satisfy kosher requirements. We suggest you confirm
acceptability with your local rabbi in respect to kosher installations.
Max. distance of
hoses and cord from
chassis edge
Left hand
side
Right hand
side
Drain hose 79”
(2011 mm)
71”
(1794 mm)
Inlet hose 61”
(1561 mm)
53”
(1344 mm)
Power cord 70”
(1776 mm)
61”
(1559 mm)
Left hand
side
Right hand
side

1
2
3
A
1
2
29 ½”- 34 ¾”
(750 -
882.5 mm)
1 ½”
(38 mm)
1
max. 4 ¾”
(120 mm)
2
1
6
5
4
7
2
29 ½”- 34 ¾”
(750 -
882.5 mm)
1
3
6
5
4
5
6
5
4
5
A
If space is limited for fixing, push
hose through drain hose support
to required height
DishDrawer® with Waste Disposal
29 ½” - 34 ¾”
(
750 - 882.5 mm)
min. R 8 ”
( 200 mm)
Supplied drain hose joiner
(ø
¾
” (19 mm)) waste tee)
HIGHLOOP
min. 6”
(150 mm)
DishDrawer® using Air Break
with Drain Hose Joiner
Supplied drain hose joiner
(ø
¾
” (19 mm)) waste tee)
Air Break
37 ⁄” ( 950 mm)
Max. height to
top of Air Break
(countertop or
wall mounted)
Fit supplied
washer
Ensure hoses are routed
straight to joiner. Remove
excess hose material if
necessary.
DishDrawer® and Standpipe
Ø 1 1/2” (38 mm)
29 ½
” - 34 ¾
”
(
750 - 882.5 mm)
min. R 8 ”
( 200 mm)
Waste Disposal
(optional)
Check all parts are installed.
Ensure product is level, securely fastened to the cabinetry and opens and closes
freely. The DishDrawer® must be free to fully close with no resistance from the
cabinetry.
Ensure inlet hose to water supply has rubber washer fitted and is tightened a
further half turn after seal contact.
Ensure any knockouts or plugs in drain connection have been drilled out and
drain connection has been made.
The drain hose joiner must not support the weight of excess hoses. Keep hoses
as fully extended as possible to prevent sagging. Any excess length of hose
should be kept on the dishwasher side of the high loop.
If using Plumbing and Drainage OPTION 1, ensure the Highloop is a minimum
6” (150 mm) higher than the drain hose joiner.
Turn on the power and water supply. Then press the power button to turn the
DishDrawer® on. The DishDrawer® should beep and Wash Programme lights
light up.
Check the spray arm(s) are in place and free to rotate.
Add three cups of water into the DishDrawer®. On the Wash Programme
Selector Panel press Rinse and close the drawer(s). Start the programme by
pressing the Start/Pause button.
After the Rinse programme has finished, ensure machine has run and drained
correctly.
Check water supply and drainage connection for leakage.
Repeat for each Drawer.
Spray arm
Excessive water remaining above the filter plate, after the rinse cycle
Check for kinked drain hoses or blocked waste connection, high loop not
properly installed or drain hoses not routed correctly.
No water supply (shows on display)
Check water is connected, turned on and the spray arm(s) is correctly fitted
and free to rotate.
No lights come on when the drawer is opened
Ensure power is connected and is switched on. Check if Auto Power option is
on.
Water around water supply and drainage connections
Check connections, existing plumbing and hoses for leaks. Check washer and
hose clamps are correctly fitted.
If product is tipping
Ensure the product is secured to the cabinetry.
If front panels are misaligned
Check and relevel product. Check the cabinetry is square.
Drawer(s) don’t close properly
Ensure nothing is obstructing the drawer(s) from closing properly ie sound
insulation, hoses or drawer latches.
If a problem occurs, consult the Troubleshooting section of the User Guide.
If after checking these points you still need assistance, please refer to the
Service & Warranty book for warranty details and your nearest Authorized
Service Centre, or contact us through our website, www.fisherpaykel.com.
599474A US CA 11.07
Tie together to avoid kinking.
x 4
123
4
5
Ensure product is level and aligning with cabinetry. Using the
most appropriate length Hexagonal socket supplied, fully extend
levelling feet up to required distance manually by hand.
Hexagonal socket
A
CC
BB
A
optional
max. ¾” (19 mm)
The mounting tabs
are in pairs, one on
each side of the
product. At least
two sets of tab pairs
must be used.
Aand Btab pairs
OR Band Ctab
pairs or all three
pairs.
Ensure the sound
insulation is
repositioned
correctly.
4 5 6 7
8 9
10
19
Important!
D o not overtighten screw.
AA
B
ROUTE THE HOSES AND MOVE INTO THE CAVITY
6
SECURE THE PRODUCT AND REFIT THE DRAWER
8
REMOVE THE DRAWER AND LEVEL THE PRODUCT
7
A
B
FIT THE TOEKICK
9
PLUMBING AND DRAINAGE OPTIONS
10
B
Fit supplied
washer
Ensure hoses are routed
straight to joiner. Remove
excess hose material if
necessary.
Fit supplied
washer
C
If space is limited for fixing, push
hose through drain hose support
to required height
FINAL CHECKLIST
11 TROUBLESHOOTING 12
2
1
1
3
3
optional
optional
If top two tabs are being used,
ensure they’re securely fitted
before sliding product into
cavity.
Ensure hoses and cord
are not kinked or twisted.
Loosen feet first, but
do not fully extend
until product is in cavity.
B
30 mm
1
2
3
4
5
5
Ensure the drawer is removed and
then rotated counter-clockwise
to prevent kinked hoses.
5 ⁄”
(
150 mm)
A
1
2
4
5
4
3
Before refitting the drawer,
ensure the hoses are not
twisted and the latches at
the rear of each drawer
runner are facing forward.
Ensure the drawer clips on
both sides are reset.
Ensure the drawer is
now rotated
clockwise back.
B