Fisher-Price 79414 User manual

Infant-to-Toddler
Soothing Rocker
Instructions
Model Numbers: 79414, 79614
Please save these instructions for future reference.
Adult assembly is required. No tools necessary.
Requires one “D” (LR20) alkaline battery (not included).
Use the upright position only when your child has developed enough
upper body control to sit without leaning forward.
Always use the restraint until your child is able to climb
in and out of the chair unassisted.
Designed for use with children from birth to 40 lbs.

1
• Position each rail so that the inner receptacles are facing
each other.
• Position the kickstand so that buttons face up.
• While pressing the button on each end of the kickstand, insert
and “snap” the kickstand into the inner receptacle on each
rail. Make sure you hear a “snap” on each end and the
buttons are visible in the inner receptacles.
2
• Position the back frame so that the soothing vibrations unit
power switch faces out.
• Make sure the top receptacle on each rail is upright.
• Press the button on each end of the frame and insert and
“snap” the back frame into the top receptacle on each rail.
Make sure you hear a “snap” on each side and the
buttons are visible in the top receptacles.
Kick Stand
Assembly
IMPORTANT! Please remove all parts from the package
and identify them before assembly. The seat back tube
may have been packaged within the pad at the factory.
Before beginning assembly, please remove the seat back
tube from the pad.
2
WARNING
Parts
Back
Frame
Seat Back
Tube
Seat Pad
2 Joints
Hardboard
Kickstand
Rail
Rail
Rail
Rail
To prevent serious injury and/or falls:
• Never use on any elevated surface.
• Always use the restraint until child
is able to climb in and out of the
chair unassisted.
• Never leave child unattended.
• Use the upright position only
when child has developed enough
upper body control to sit without
leaning forward.
Front
Frame
IMPORTANT! Before assembly or each usage, inspect this
product for damaged hardware, loose joints, missing parts or
sharp edges.
This product contains small parts
in its unassembled state.
Adult assembly is required.
CAUTION
Buttons
Inner
Receptacles
Back Frame
Soothing
Vibrations Unit
Soothing
Vibrations
Unit
Button
Button
Rail
Rail
Top
Receptacle
Top
Receptacle

3
• Position the front frame so that it bends back towards the
back frame and the notched end is down.
• Make sure the top receptacle on each rail is upright.
• While pressing the button on each end of the front frame,
insert and “snap” the front frame into the top receptacle
on each rail. Make sure you hear a “snap” on each side
and the buttons are visible in the top receptacles.
Assembly
4
• Lift the front frame up slightly.
• Position one of the joints so the push button is outward and
the ribbed opening is upright. Fit the joint onto one of the
ends of the front frame.
• Press the button on the inside of the front frame. Slide the
joint down until the button “snaps” into place. Make sure
you hear a “snap”.
• Repeat this procedure to attach the other joint to the other
end of the front frame.
Front Frame
Button
Joint
Push
Button
Ribbed
Opening
Ribbed
Opening
3
5
• Position the seat back tube so that the open ends are forward.
• Press the button on each end of the seat back tube and insert
the ends of the seat back tube into the joints on the frame.
• Push the seat back tube into the joints until the buttons “snap”
into place. Make sure you hear a “snap” on each side.
• Pull up on the seat back tube to be sure it is secure.
Seat Back Tube
Buttons
Joints
Tapered
Ends
Backward
Open
Ends
Forward
6
• Slide the pad over the seat back tube.
• Pull the pad down over the frame.
Pad
Rail
Button
Button
Top
Receptacle
Notched End
Top
Receptacle
Front Frame
Back Frame

Assembly
4
8
• Turn the hardboard over and insert it into the pocket in the
bottom of the pad.
• Push the front frame and rear frame toward each other.
• Press the push button on each joint and fit each joint into
the groove in each end of the rear frame. Make sure both
push buttons “snap” into the hole in each end of the
rear frame.
• Check to be sure the front and rear frames are assembled
correctly, by pulling them away from each other.The frames
should remain attached to each other.
Pocket
Hardboard
• Turn the seat face down.
• Fasten both buckles together. Make sure you hear a “snap”
on both sides
Buckles
Push Button
Rear Frame
Groove
Hole
Front Leg
(Underneath Pad)
79

Set-Up and Use
• Pull both rear legs up until the small buttons “snap” into
place. Make sure you hear a “snap” on both sides.
Buttons
Rear Legs
Upright Position
• Press the small button on each rear leg and push the rear
frame down completely.
Semi-Recline Position
Rear Legs
Buttons
1
2
To prevent serious injury and/or falls:
• Never use on any elevated surface.
• Use the upright position only when child
has developed enough upper body
control to sit without leaning forward.
WARNING
Battery Installation
• Insert a coin into the slot in the battery compartment door.
Pry the battery compartment door open.
• Insert one “D” alkaline battery as shown inside the
battery compartment.
Hint: Use only an alkaline battery for longest battery life.
• Replace the battery compartment door and be sure it snaps
securely closed.
Battery Tips
• Remove the battery during long periods of non-use.Always
remove an exhausted battery from the product. Battery
leakage and corrosion can damage this product. Dispose of
the battery safely.
• Never short circuit the battery terminals.
• A non-rechargeable battery is not to be recharged.
• Only a battery of the same or equivalent type as recommended
in the Battery Installation instructions is to be used.
• If a removable rechargeable battery is used, it is only to be
charged under adult supervision.
• A rechargeable battery is to be removed from the product
before it is charged.
• If you use a battery charger, it should be examined regularly for
damage to the cord, plug, enclosure and other parts. Do not use
a damaged battery charger until it has been properly repaired.
1.5V
“D” (LR20)
SHOWN ACTUAL SIZE
5
Battery
Compartment
IMPORTANT! Before each usage or assembly, inspect this prod-
uct for damaged hardware, loose joints, missing parts or sharp
edges. Do not use if any parts are missing or broken. Contact
Fisher-Price®for replacement parts and instructions if needed.
Never substitute parts.

• Place your child in the seat. Position the restraint pad
between your child’s legs.
• Fasten the restraint straps to the restraint pad. Make sure you
hear a “click” on both sides.
• Make sure the restraint is securely attached by pulling it away
from your child.The restraint should remain buckled.
Securing Your Infant
Set-Up and Use
Restraint
Strap
Restraint
Strap
Restraint Pad
6
3
• Fit the ends of the toy
bar through the loops
in each side of the pad.
• From the back of the
seat, insert the toy bar
long straps through the
slots on each rear leg.
• Fasten the straps
together.
• Fasten the toys to the
straps on the toy bar.
5
To prevent serious injury and/or falls:
• Never use on any elevated surface.
• Always use the restraint until child is
able to climb in and out of the chair
unassisted.
• Never leave child unattended.
WARNING
To tighten the restraint straps:
• Feed the anchored end of the restraint strap up through the
buckle to form a loop .
• Pull the free end of the restraint strap .
• Repeat this procedure to tighten the other restraint strap B.
To loosen the restraint straps:
• Feed the free end of the restraint strap up through the buckle
to form a loop .
B
B
Anchored
End
Free End
Tighten Restraint Loosen Restraint
Back View
B
Anchored
End
Buckle
Free End
Buckle
B
4
• Enlarge the loop by pulling on the end of the loop toward
the buckle.
• Pull the anchored end of the restraint strap to shorten the
free end of the restraint strap .
• Repeat this procedure to loosen the other restraint strap .
Note: After adjusting the restraint straps to fit your child, make
sure you pull on them to be sure they are securely fastened.
Toy Bar
Toys
Loop
Loop
Straps
Toy Bar
Slot
Slot
Strap
Strap

Set-Up and Use
7
Stationary Feeding Seat
Kickstand
• Position the seat in the upright or semi-recline position.
• Rotate the kickstand out.
• Make sure your child is properly secured in the seat.
• Slide the ON/OFF switch on the soothing unit to the ON
position.The seat will vibrate.
• Slide the ON/OFF switch on the soothing unit to the OFF
position.The seat will not vibrate.
ON
OFF
Soothing Unit
6
6
To prevent serious injury and/or falls:
• Never use on any elevated surface.
• Always use the restraint until child is
able to climb in and out of the chair
unassisted.
• Never leave child unattended.
WARNING
Soothing Vibrations
IMPORTANT! When soothing vibrations become slow or
vibrations stop, it’s time to replace the battery. Please refer to
the “Battery Installation” section on page 5.
Storing the Toy Bar
Storing Restraint System
for Toddler Use
• Insert the restraint straps through the small slots in the pad.
• Insert the restraint pad down through the large slot in the pad.
• Turn the seat so that the back is facing you.
• Fasten the straps around the ends of the toybar.
Restraint
Strap Restraint
Strap
Restraint
Pad
Back View
Toy Bar
Straps
Straps

Care
The pad is machine washable.Wash the pad separately in cold
water on the gentle cycle. Do not use bleach.Tumble dry sepa-
rately on low heat and remove promptly. Surface wash the
frame, with mild detergent and water. Do not use bleach. Do not
use harsh or abrasive cleaners. Rinse clean with water to
remove residue.
To remove the pad:
• Unfasten the buckles on the bottom of the pad.
• Remove the hardboard from the pocket in the pad.
• Press the push buttons on each joint to disassemble the front
and rear frames.
• Remove the pad.
• After washing, re-assemble the pad to the frame with hard-
board (see Assembly steps 6-9).
If you have any questions about this product:
In Canada, call 1-800-567-7724, or write to: Mattel Canada Inc., 6155 Freemont Blvd., Mississauga, Ontario L5R 3W2.
In Great Britain, telephone [phone].
In Australia, call the Fisher-Price Australian Consumer Advisory Service toll-free at 1-800-800-812, or write to: Fisher-Price, Mattel Pty. Limited, 461 Plummer Street,
Port Melbourne, Victoria 3207.
8
Fisher-Price, Inc., a subsidiary of Mattel, Inc.,
East Aurora, New York, 14052 U.S.A.
©2000 Mattel, Inc. All Rights Reserved Printed in China
® and ™ designate U.S. trademarks of Mattel, Inc. 79414pr-0920
One (1) Year
Limited Warranty
Fisher-Price, Inc., 636 Girard Avenue, East Aurora, New York
14052 warrants that the Infant-to-Toddler Soothing Rocker is
free from all defects in material and workmanship when used
under normal conditions for a period of one (1) year from the
date of purchase.
Should the product fail to perform properly, we will repair or
replace it at our option, free of charge. Purchaser is responsible
for shipping the product to Consumer Relations at the address
indicated above and for all associated freight and insurance cost.
Fisher-Price, Inc. will bear the cost of shipping the repaired or
replaced item to you.This warranty is void if the owner repairs
or modifies the product.This warranty excludes any liability
other than that expressly stated above including but not limited
to any incidental or consequential damages.
SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMI-
TATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES,
SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT
APPLY TO YOU.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS,
AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH MAY
VARY FROM STATE TO STATE.
Consumer Information
Occasionally a consumer may experience a problem with one
of our products. If this should happen, please call us, toll-free,
rather than return this product to the store. Usually we can
solve the problem on the telephone or by sending you replace-
ment parts. Please call Fisher-Price®Consumer Relations,
toll-free at 1-800-432-KIDS, 8 AM - 6 PM EST Monday through
Friday. Hearing-impaired consumers using TTY/TDD equipment,
please call 1-800-382-7470. Or, write to:
Fisher-Price®Consumer Relations
636 Girard Avenue
East Aurora, New York 14052