Fisher-Price CJV02 User manual

1
CJV02
fisher-price.co.uk
IMPORTANT! KEEP FOR FUTURE REFERENCE.
IMPORTANT! Read the instructions carefully before use and keep them for future reference.
Please read these instructions before assembly and use of this product.
Adult assembly is required.
Tool needed for assembly: Phillips screwdriver (not included).
Requires four C (LR14) alkaline batteries for operation (not included).
This product does not replace a cot or a bed. Should your child need to sleep,
then it should be placed in a suitable cot or bed.
Product features and decorations may vary from photographs.

2
Consumer Information
IMPORTANT! The weight limit for this product is 9 kg. If your child weighs less than 9 kg, but is
really active and appears to be able to climb out of the swing, immediately discontinue its use.
IMPORTANT! Before each use or assembly, inspect this product for damaged hardware, loose
joints, missing parts or sharp edges. Do not use the product if any components are broken
or missing. Do not use accessories or replacement parts other than those approved by the
manufacturer. Never substitute parts.
WARNING
To prevent serious injury or death from falls or being strangled in the
restraint system:
• Never leave the child unattended.
• Always use the restraint system.
• Do not use this product once your child can sit up unaided or weighs more
than 9 kg.
• This product is not intended for prolonged periods of sleeping.
• It is dangerous to use this product on an elevated surface, e.g. a table.
• To avoid injury ensure that children are kept away when unfolding and folding
this product.
• Do not let children play with this product.
• Do not move or lift this product with the baby inside it.
• When used as an infant seat:
• Suffocation Hazard - Never use on a soft surface (bed, sofa, cushion), since the
product can tip over and cause suffocation in soft surfaces

3
Parts
Swing Housing 2 Swing Legs
(left and right)
Rear Cross BraceSeat Pad
Front Cross Brace
Please remove all parts from the package and identify them before assembly. Some parts may be
packed in the pad.
4,5 mm x 12 mm Screw – 6
Note: Tighten or loosen all screws with a Phillips
screwdriver. Do not over-tighten the screws.

4
©2014 Mattel. All Rights Reserved.
PRINTED IN CHINA CJV02_1100216399_UU1
Great Britain: Vanwall Business Park, Maidenhead SL6 4UB. Helpline: 01628 500303.
www.service.mattel.com/uk.
Mattel Europa B.V., Gondel 1, 1186 MJ Amstelveen, Nederland.
Australia: Mattel Australia Pty. Ltd., 658 Church Street, Locked Bag #870, Richmond,
Victoria 3121 Australia. Consumer Advisory Service 1300 135 312.
New Zealand: 16-18 William Pickering Drive, Albany 1331, Auckland.
Asia: Mattel East Asia Ltd, Room 503-09, North Tower, World Finance Centre, Harbour City,
Tsimshatsui, HK, China.
Malaysia: Diimport & Diedarkan Oleh: Mattel Southeast Asia Pte. Ltd., No 19-1, Tower 3 Avenue
7, Bangsar South City, No 8, Jalan Kerinchi, 59200 Kuala Lumpur, Malaysia. Tel: [phone],
Fax: [phone].

5
Assembly
• Rotate the straight tube on each swing leg.
• Make sure you hear a "click".
1
• While pressing a button on the rear cross brace, fit it into a swing leg.
• Make sure you hear a "click".
• Repeat this procedure to insert the other end of the rear cross brace into the other swing leg.
2Rear Cross Brace
PRESS
PRESS Swing Leg
Swing Leg

6
• Turn the leg assembly over.
• Fit the front cross brace onto the swing legs.
Assembly
3
Front Cross Brace
BOTTOM VIEW
• Insert two screws into the front cross brace and tighten.
• Turn the leg assembly upright.
4

7
Assembly
5
• First, tilt the swing housing so the sockets are facing down.
• Then, fit the swing housing onto the free end of each swing leg. Push to "snap" in place.
• Pull up on the swing housing to be sure it is secure.
Hint: The swing housing is designed to fit onto the swing legs one way. If it does not seem to fit,
turn it around and try again.
BACK VIEW
• Fit one side of the seat onto a swing arm.
• Insert two screws into the seat and tighten.
• Repeat this procedure to assemble the other side of the seat.
6
Swing Arm
Seat
C
Swing Housing

8
Assembly
7
• Fit the seat pad back pocket onto the seat back.
8
Seat Pad
Back Pocket
• Lower the seat bottom.

9
10
• Fasten the buckles on the side of the seat pad to the buckles on the swing arms. Make sure you
hear a “click”.
Assembly
• First, lift the seat bottom A. Next, fit the lower seat pad pocket onto the seat bottom B. Then,
pull the seat bottom down C.
9
Seat Pad
Lower Pocket
B
A
C

10
Upper Slots
Assembly
• Insert the waist belts through the lowest slots in the seat pad. Make sure the waist belts are
not twisted.
11
Smaller Baby
• Insert the ends of the shoulder belts through the lower slots in the seat pad back. Make sure
the shoulder belts are not twisted.
Larger Baby
• Insert the ends of the shoulder belts through the upper slots in the seat pad back. Make sure
the shoulder belts are not twisted.
12
Lowest Slots
Lower Slots
2
Lower
S