Fisher-Price SOOTHING SOUNDS BOUNCER SEAT 79598 User manual

SOOTHING SOUNDS
BOUNCER SEAT
Model Number: 79598
Please save these instructions for future reference.
Adult assembly is required. Tools required for assembly: Phillips Screwdriver
and adjustable wrench (not included).
Requires three “C” (LR14) alkaline batteries (not included).

22
Occasionally a consumer may experience
a problem with one of our products.
If this should happen, please call us toll-free,
rather than return this product to the store.
Usually, we can solve the problem over the telephone
or send you replacement parts.
Please call Fisher-Price® Consumer Relations,
toll-free at 1-800-432-KIDS,
between 8 AM - 6 PM EST, Monday through Friday.
Hearing-impaired consumers using TTY/TDD equipment,
please call 1-800-382-7470.
Or write to:
Fisher-Price® Consumer Relations
636 Girard Avenue
East Aurora, New York 14052
CCOONNSSUUMMEERR IINNFFOORRMMAATTIIOONN
WWAARRNNIINNGGSS
To prevent serious injury and/or falls:
• Never use on any elevated surface.
• Never use as a carrier or lift while child
is seated.
• Always use the restraint system.
• Never leave child unattended.
• Never use as a car seat.
• Never use with a child able to sit
up, unassisted.
WARNING

33
PPAARRTTSS
1/2" Screw - 2
3 Toys
Pad
Footrest
Seatback Tube
Right Base Tube
Left Base Tube
Base
Connector
Cuddle Cushion
Shown Actual Size
Lock Nut - 2

44
BBAATTTTEERRYY IINNSSTTAALLLLAATTIIOONN
• Locate the soothing unit on the footrest wire.
• Loosen the screw in the soothing unit battery compartment door with a
Phillips screwdriver.
• Remove the battery compartment door.
• Insert three "C" (LR14) batteries, as indicated inside the battery compartment.
• Replace the battery compartment door. Tighten the screw with a Phillips screwdriver.
Do not over-tighten.
Battery Compartment Door
1.5V x 3
“C” (LR14)
SHOWN ACTUAL SIZE
+
–
Battery Tips
• Do not mix old and new batteries.
• Do not mix different types of batteries: alkaline, standard (carbon-zinc) or
rechargeable (nickel-cadmium).
• Remove the batteries during long periods of non-use. Always remove the
exhausted batteries from the product. Battery leakage and corrosion can damage
the product. Dispose of the batteries safely.
• Never short circuit the battery terminals.
• Non-rechargeable batteries are not to be recharged.
• Only batteries of the same or equivalent type as recommended in the “Battery
Installation” instructions are to be used.
• If removable rechargeable batteries are used, they are only to be charged under
adult supervision.
• Rechargeable batteries are to be removed from the product before they
are charged.
• If you use a battery charger, it should be examined regularly for damage to the
cord, plug, enclosure and other parts. Do not use a damaged battery charger until
it has been properly repaired.

55
AASSSSEEMMBBLLYY
• Place the base connector on a flat surface as shown.
• Position the left and right base tubes as shown. Note the locations of the
colored dots on the left and right base tubes.
• Fit the left base tube into the base connector.
• Fit the right base tube into the base connector.
•Make sure both colored dots on the base tubes are covered by the
base connector.
11
This package contains small parts
in its unassembled state.
Adult assembly is required.
CAUTION
Base
Connector
Colored Dots
Right Base
Tube
Left Base
Tube

66
• Position the footrest so that the soothing
unit is upright.
• While flexing the base tubes toward each
other, hook the footrest onto the ends of the base tubes.
• Push the footrest down completely, to the tabs on the base tubes.
• Make sure the small tabs on the left and right base wires are secure in
the base connector holes (see inset). If the small tabs are not secure in
the base connector holes, you have assembled the base incorrectly.
Disassemble all parts and refer back to Assembly Step 1.
AASSSSEEMMBBLLYY
22
Base Tube
Tab
Tab
Base Tube
Soothing
Unit
Footrest
Back View
Base
Connector
Base
Tube

77
33
• Position the seat back tube above the base assembly. The seat back tube
should bend backward.
• Fit the seat back tube completely onto the base tubes.
• Insert a screw through the hole in the outside of the seat back tube.
• Attach a lock nut to the end of the screw on the inside of the seat
back tube.
• While holding the lock nut in place with an adjustable wrench, tighten
the screw with a Phillips screwdriver. Do not over-tighten.
• Repeat this procedure to secure the other side of the seat back tube
to the base assembly using the remaining screw and lock nut.
AASSSSEEMMBBLLYY
Base
Tube
Base
Tube
Seat Back
Tube

88
AASSSSEEMMBBLLYY
• Pull up on the seat back tube to be sure it is secure. If you can remove
either end of the seat back tube, you have not assembled it correctly.
Remove the screws and lock nut. Re-read and repeat Assembly steps
3 and 4.
Pull Up
44

99
AASSSSEEMMBBLLYY
• Position the pad with the canopy up.
• Fit the upper pocket on the back of the pad onto the seat back tube .
• Lift the footrest. Fit the lower pocket on the back of the pad onto the
footrest . Lower the footrest.
• Attach the pad fastener to the fastener on the soothing unit.
A
B
55
Seat Back
Tube
Footrest
Pad
Fastener
B
Fastener

1100
• Attach the toys to the canopy fasteners.
88
3 Toys
66
AASSSSEEMMBBLLYY