Fisher-Price H5985 User manual

Infant Seat Toddler Seat
WARNING
IMPORTANT! KEEP FOR FUTURE REFERENCE.
www.fisher-price.com
Instructions
Model Number: H5985
Please read these instructions before assembly and use of this product.
Use the upright position only when your child has developed enough upper
body control to sit without leaning forward.
Always use the restraint until your child is able to climb in and out of the chair unassisted.
Adult assembly is required. Tool needed for assembly: Phillips Screwdriver (not included).
Requires one LR20 ("D") alkaline battery (not included) for vibrations unit operation.

WARNING
To prevent serious injury or death:
• It is dangerous to use this product on
an elevated surface.
• Never use on a soft surface (bed, sofa,
cushion) since product can tip over and
cause suffocation in soft surfaces.
• Always use the restraint until child
is able to climb in and out of the
chair unassisted.
• Never leave child unattended.
• Use the upright position only when child
has developed enough upper body
control to sit without leaning forward.
• Never use as a carrier or lift while child
is seated. Never use the toy bar as
a handle.
• Reclined position not recommended for
children who can sit up by themselves
(6 months approximately, until 9 kg.).
Parts
IMPORTANT! Please remove all parts from the package and
identify them before assembly. The kickstand is packaged
within the pad at the factory. Before beginning assembly,
please remove kickstand from the pad.
Note: Tighten or loosen all screws with a Phillips
screwdriver. Do not over-tighten.
All Shown Actual Size
M4 Lock Nut (Inside Retainers) - 2
#8 x 2.9 cm Screw - 2 #8 x 1.9 cm Screw - 2
CAUTION
This package contains small parts
in its unassembled state.
Adult assembly is required.
Toy Bar 3 Toys
Seat Back Tube
2 Retainers with Lock Nut
Cross Brace
Kickstand
Pad
Front Tube 2 Side Rails
2
2

1
Assembly
IMPORTANT! Before assembly or each use, inspect this product
for damaged hardware, loose joints, missing parts or sharp edges.
DO NOT use if any parts are missing, damaged or broken. Contact
Mattel for replacement parts and instructions if needed. Never
substitute parts.
Side Rails
Cross Brace (Push)
Button
• Position each side rail so that the button faces outward.
•Fit the cross brace between the side rails, as shown.
•Push the cross brace down to "snap" it into place. This may
require a lot of force.
2
#8 x 1.9 cm Screw
Cross Brace
Side Rails
•Insert a #8 x 1.9 cm screw through the hole in the bottom of
each side rail and into the cross brace. Tighten the screws with
a Phillips screwdriver. Do not over-tighten.
3
Press Tabs
Seat Back Tube
Side Rail Sockets
•Insert the seat back tube into the socket in each side rail.
•While pressing the tabs on the ends of the seat back tube,
continue to insert the seat back tube into the sockets in each
side rail, until the tabs "snap" into place. Make sure you hear
a "snap" on each side.
•Pull the seat back tube up to be sure it is secure in the side
rail sockets.
4
Side Rail Hole
Front Tube
Vibrations Unit Side Rail Hole
•Locate the hole in each side rail.
•With the vibrations unit facing forward, fit the front tube
to the side rails, as shown. Hold the front tube in place and
proceed to step 5.
3
3

Assembly
5
Side Rail
#8 x 2.9 cm Screw
Side Rail
Front Tube
•Insert a #8 x 2.9 cm screw through the outside of each side rail
and into the ends of the front tube.
IMPORTANT! Please follow the next assembly (step 6) carefully to
completely secure the front tube to the side rails.
6
Rounded Side
M4 Lock Nut (Inside Retainer) - 2
•Fit a retainer with lock nut onto the end of the screw and to
the inside of a side rail.
Hint: A lock nut has been factory assembled to the retainer.
During shipment, the lock nut may have fallen out of the retainer.
If it has, please fit it into the hexagonal hole in the retainer so
that the rounded side of the lock nut faces out.
•Tighten the screw with a Phillips screwdriver. Do not over-tighten.
•Repeat this procedure to fasten the screw in the other end of
the front tube and side rail, using the remaining retainer with
lock nut.
Retainer with Lock Nut 7
Kickstand
Press Tab
Receptacles
Press Tab
•Position the assembly face down, as shown.
•While pressing the tab on each end of the kickstand, insert the
kickstand into the receptacle in each side rail, as shown.
•Push the kickstand into the receptacles until the tabs "snap"
into place. Make sure you hear a "snap" on each side.
•Pull the kickstand to be sure it is secure in the receptacles.
4
4

Assembly
9
Pad Slot
Press Seat Back
Hardboard
Pad Buckles
•Turn the hardboard over and insert it into the slot in the front
edge of the pad.
•Fasten the pad buckles on the front edge of the pad and under-
neath the seat. Make sure you hear a "snap" on both sides.
•Press the fasteners together in the seat back portion of the pad.
•Turn the assembly upright.
•Fit the upper pocket on the pad onto the seat back tube.
•Fasten the pad buckles around each side rail.
8
Pad
Seat Back Tube
Pad Buckles
Side Rail
5
5

Battery Installation
Shown Actual Size
1,5V
LR20 (“D”)
•Locate the battery compartment on the bottom of the
vibrations unit.
•Loosen the screw in the battery compartment door with a
Phillips screwdriver.
•Lift to remove the battery compartment door.
•Insert one LR20 ("D") alkaline battery as indicated inside the
battery compartment.
Hint: We recommend using alkaline batteries for longer
battery life.
•Replace the battery compartment door and tighten the screw
with a Phillips screwdriver. Do not over-tighten.
Battery Compartment
+–
Battery Safety Information
Batteries may leak fluids that can cause a chemical burn injury
or ruin your product. To avoid battery leakage:
•Do not mix old and new batteries or batteries of different
types: alkaline, standard (carbon-zinc) or rechargeable
(nickel-cadmium).
•Insert batteries as indicated inside the battery compartment.
•Remove batteries during long periods of non-use. Always
remove exhausted batteries from the product. Dispose of
batteries safely. Do not dispose of batteries in a fire. The
batteries may explode or leak.
•Never short-circuit the battery terminals.
•Use only batteries of the same or equivalent type,
as recommended.
•Do not charge non-rechargeable batteries.
•Remove rechargeable batteries from the product before charging.
•If removable, rechargeable batteries are used, they are only to
be charged under adult supervision.
6
6

Setup and Use
To prevent serious injury or death:
•Reclined position not recommended for
children who can sit up by themselves
(6 months approximately, until 9 kg.).
•Use the upright position only when child
has developed enough upper body
control to sit without leaning forward.
WARNING
IMPORTANT! Before each use, inspect this product for damaged
hardware, loose joints, missing parts or sharp edges. DO NOT use if
any parts are missing or broken. Contact Mattel for replacement
parts and instructions if needed. Never substitute parts.
Seat Position
Lift
Upright Press Button
1
Lower
Recline Press Button
Select a seat position for your child’s comfort:
Upright or Recline.
Upright
While pressing the button on each side rail, lift the seat back.
Recline
While pressing the button on each side rail, lower the seat back.
7
7

Securing Your Infant
To prevent serious injury or death:
•Always use the restraint until child is
able to climb in and out of the chair
unassisted.
•It is dangerous to use this product on
an elevated surface.
•Never leave child unattended.
WARNING
Restraint Belt
2Restraint Pad
Restraint Belt
•Place your child in the seat. Position the restraint pad between
your child’s legs.
•Fasten the restraint belts to each side of the restraint pad.
Make sure you hear a “click”on both sides.
•Check to be sure the restraint system is securely attached by
pulling it away from your child. The restraint system should
remain attached.
Free End
Tighten Loosen
Anchored End
Free End
Anchored End
To tighten the belts: Feed the anchored end of the restraint belt
up through the buckle to form a loop . Pull the free end of
the restraint belt . Repeat this procedure to tighten the other
restraint belt.
To loosen the belts: Feed the free end of the restraint belt up
through the buckle to form a loop . Enlarge the loop by pulling
on the end of the loop toward the buckle. Pull the anchored
end of the restraint belt to shorten the free end of the restraint
belt . Repeat this procedure to loosen the other restraint belt.
8
8
3

Toy Bar
•Fit the plugs on each end of the toy bar into the sockets
in each side rail.
•Fit the toy bar straps through the slot in the toy rings.
Fasten the straps.
•Or, attach the toys to the pad straps.
4
Plug
Plug
Toys
Toy Bar
Calming Vibrations
5Power Switch
•Make sure your child is properly secured in the seat.
•Slide the power switch to the on position for calming
vibrations.
•Slide the power switch to the Ooff position to turn
vibrations off.
Kickstand
6Kickstand
•Rotate the kickstand out.
•Push down on the seat bottom to be sure the kickstand is
in position.
9
9

Storing the Restraint System for Toddler Use
7
Small Slots
Large Slot
•Insert the restraint belts back through the small slots in the pad.
•Insert the restraint pad down through the large slot in the pad.
8
•Turn the rocker face down.
•Tuck the ends of the restraint pad underneath the buckles,
as shown.
10
10