Fisher-Price P5748 User manual

www.fisher-price.com.au
P5748
IMPORTANT!
KEEP INSTRUCTIONS FOR
FUTURE REFERENCE.

2
This package contains small parts
in its unassembled state.
Adult assembly is required.
Prevent serious injury or death from falls or
sliding out:
• Always use the restraint system for the
upright and reclined positions of the seat.
Adjust restraint to fit your child snugly.
The tray is not designed to hold the child
in the chair.
• It is recommended that only children
capable of sitting upright unassisted use
the upright position of the high chair.
• Position the high chair away from steps,
hot surfaces, electrical cords and other
items that may cause injury to the child.
• Always keep child in view while in
high chair.
• Never leave child unattended.
• Follow the manufacturer’s instructions.
WARNING
Consumer Information
IMPORTANT! Please keep these instructions for future reference.
Please read these instructions before assembly and use of•
this product.
Adult assembly is required. Tool needed for assembly:•
Allen wrench (included).
Product features and decorations may vary from photographs.•
CAUTION

3
2 Front Legs 2 Back Legs
Footrest
Parts
All Fasteners Shown Actual Size
Tighten the screws with the enclosed Allen wrench.
Back Base
Seat Back with Shoulder
and Waist Belts
Seat Bottom with
Crotch Belt
2 Seat Brackets
Allen Wrench
Food Tray Snack Tray
Seat Pad
Front Base
M4 x 17mm Screw – 6 M5 x 59,5mm Screw – 6 M6 x 28mm Screw – 10

4
Turn the seat bottom upside down on a flat surface.•
Position a back leg so that it curves up and fit it into a large•
socket in the seat bottom.
Hint: If the leg does not seem to fit into the seat bottom socket,
try the other back leg.
Fit the other back leg into the large socket in the seat bottom.•
Insert an M5 x 59,5mm screw into the side of the seat bottom•
and tighten.
Push the back leg until it• "snaps" in place.
Insert an M5 x 59,5mm screw into the side of the seat bottom•
and tighten.
Push the back leg until it• "snaps" in place.
Assembly
1
3
4
2
IMPORTANT! Before assembly and each use, inspect this product
for damaged hardware, loose joints, missing parts or sharp edges.
DO NOT use if any parts are missing or broken. Contact Fisher-Price®
for replacement parts and instructions if needed. Never substitute parts.
Back Leg
Large Socket
Seat Bottom
Back Leg
PUSH
PUSH M5 x 59,5mm
Screw
M5 x 59,5mm
Screw

5
Position a front leg so that it curves up and fit it into the small•
socket in the seat bottom.
Hint: If the leg does not seem to fit into the seat bottom, try the
other front leg.
Fit the other front leg into the small socket in the seat bottom.•
Insert two M5 x 59,5mm screws into the other side of the seat•
bottom and tighten.
Insert two M5 x 59,5mm screws into the side of the seat bottom•
and tighten.
5 7
6
8
Front Leg
Small Socket
Assembly
Seat Bottom
Front Leg
M5 x 59,5mm
Screws
M5 x 59,5mm
Screws

6
Assembly
Fit the back base onto the bottom of both back legs, as shown.•
Insert two M6 x 28mm screws into• each back leg and tighten.
Fit the sockets on the footrest onto the posts on the front of•
the assembly.
Slide the footrest up onto the posts.•
Hint: You may want to lower the seat to assemble the footrest.
Refer to page 13 for instructions to lower the seat.
Fit the front base onto the bottom of both front legs.•
Insert two M6 x 28mm screws into• each front leg and tighten.
Turn the assembly upright.•
9
10
Back Base
M6 x 28mm
Screws
M6 x 28mm
Screws
Back Legs
Front Base
Front Legs
Footrest
Posts
11
While holding the footrest in place, insert two M6 x 28mm screws•
into the holes on the back of the footrest and tighten.
12
BACK VIEW
M6 x 28mm Screws
M6 x 28mm
Screws
M6 x 28mm
Screws

7
Assembly
13
Seat Back
Peg
Holes
At an angle, fit the pegs on each side of the seat back into the•
holes in the sides of the seat bottom.
Hint: You may need to flex the bottom edge of the seat back to fit
the seat back pegs into the holes in the seat bottom.
Lift the seat back latch and push the seat back forward.•
14
Insert two M4 x 17mm screws into the seat back and tighten.•
15
M4 x 17mm
Screws
M4 x 17mm
Screws
Seat Bracket
Fit a seat bracket to the side of the seat bottom, as shown.•
Insert two M4 x 17 mm screws and tighten.•
16
BACK VIEW

8
Assembly
Fit the other seat bracket to the other side of the seat bottom,•
as shown.
Insert two M4 x 17 mm screws and tighten.•
17
M4 x 17mm
Screws
Seat Bracket
Unbuckle the lower restraint.•
18
Lower Restraint
Hint: The shoulder belts come assembled to the seat back in the
lower position for a smaller child. To change to the upper slots for
a larger child, refer to page 12.
Place the seat pad onto the seat.•
Pull the shoulder belts ends through the slots in the seat pad.•
19
Shoulder Belt
Shoulder Belt
Slots
Pull the waist belt ends through the slots in the seat pad.•
Pull the crotch belt through the slot in the seat pad.•
20
Seat Pad
Slot
Waist Belts
Crotch Belt

9
Fit the elastic loops on the seat pad down through the slots in•
the footrest.
21
Elastic Loops
Slots
Assembly
Fit the elastic loops on the seat pad bottom onto the pegs on•
the footrest.
22
Pegs
BACK VIEW Fit the upper pocket of the seat pad onto the seat back.•
Fit the ends of the waist belts through the clips on the•
shoulder belts.
24
23
Shoulder Belts

10
Securing Your Child
Place your child in the seat. Position the crotch belt between your•
child’s legs.
Fasten both waist/shoulder belts to each side of the crotch belt.•
Make sure you hear a• "click" on both sides.
Check to be sure the restraint system is securely attached by•
pulling it away from your child. The restraint system should
remain attached.
1
Waist/Shoulder
Belt
Waist/Shoulder
Belt
Crotch Belt
Prevent serious injury or death from falls or
sliding out:
• Always use the restraint system for the
upright and reclined positions of the seat.
Adjust restraint to fit your child snugly.
The tray is not designed to hold the child
in the chair.
• It is recommended that only children
capable of sitting upright unassisted use
the upright position of the high chair.
• Position the high chair away from steps,
hot surfaces, electrical cords and other
items that may cause injury to the child.
• Always keep child in view while in
high chair.
• Never leave child unattended.
• Follow the manufacturer’s instructions.
WARNING