Fisher-Price 79436 User manual

SOOTHING
BOUNCER SEAT
Model Number: 79436
Please save these instructions for future reference.
Adult assembly is required. Tool required for assembly: Phillips Screwdriver (not included).
Requires one “D” (LR20) alkaline battery (not included).
79436pr-0920.qrk 9/22/00 11:00 AM Page 1

22
Occasionally a consumer may experience
a problem with one of our products.
If this should happen, please call us toll-free,
rather than return this product to the store.
Usually, we can solve the problem over the telephone
or send you replacement parts.
Please call Fisher-Price® Consumer Relations,
toll-free at 1-800-432-KIDS,
between 8 AM - 6 PM EST, Monday through Friday.
Hearing-impaired consumers using TTY/TDD equipment,
please call 1-800-382-7470.
Or write to:
Fisher-Price® Consumer Relations
636 Girard Avenue
East Aurora, New York 14052
CCOONNSSUUMMEERR IINNFFOORRMMAATTIIOONN
WWAARRNNIINNGGSS
To prevent serious injury and/or falls:
• Never use on any elevated surface.
• Never use as a carrier or lift while child
is seated.
• Always use the restraint system.
• Never leave child unattended.
• Never use as a car seat.
• Never use with a child able to sit
up, unassisted.
WARNING
79436pr-0920.qrk 9/22/00 11:00 AM Page 2

33
PPAARRTTSS
#8 x 3/4" Screw - 2
Shown Actual Size
3 Rings
2 Paddles
Mirror
Pad Footrest
Seatback Tube
Retainer
Retainer
Right Base Tube
Left Base
Tube
Base
Connector
79436pr-0920.qrk 9/22/00 11:00 AM Page 3

44
BBAATTTTEERRYY IINNSSTTAALLLLAATTIIOONN
• Locate the soothing unit on the footrest.
• Insert a coin into the battery compartment door and pry the battery
compartment door off.
• Insert one “D” (LR20) alkaline battery, as indicated inside the
battery compartment. Be sure to place the battery on top of the ribbon.
Hint: We recommend the use of an alkaline battery for longest battery life.
• Replace the battery compartment door and be sure it snaps securely closed.
Hint: For easy battery removal, simply lift the ribbon.
1.5V
“D” (LR20)
Battery Tips
• Remove the battery during long periods of non-use. Always remove an
exhausted battery from the product. Battery leakage and corrosion can
damage the product. Dispose of the battery safely.
• Never short circuit the battery terminals.
• A non-rechargeable battery is not to be recharged.
• Only a battery of the same or equivalent type as recommended
in the “Battery Installation” instructions is to be used.
• If a removable rechargeable battery is used, it is only to be charged
under adult supervision.
• A rechargeable battery is to be removed from the product before it is charged.
• If you use a battery charger, it should be examined regularly for damage
to the cord, plug, enclosure and other parts. Do not use a damaged
battery charger until it has been properly repaired.
SHOWN ACTUAL SIZE
+
–
Battery Compartment
Door
79436pr-0920.qrk 9/22/00 11:00 AM Page 4

55
AASSSSEEMMBBLLYY
• Place the base connector on a flat surface as shown.
• Position the left and right base tubes as shown. Note the locations of the
colored dots on the left and right base tubes.
• Fit the left base tube into the base connector.
• Fit the right base tube into the base connector.
•Make sure both colored dots on the base tubes are covered by the
base connector.
11
This package contains small parts
in its unassembled state.
Adult assembly is required.
CAUTION
Base
Connector
Colored Dots
Right Base
Tube
Left Base
Tube
79436pr-0920.qrk 9/22/00 11:00 AM Page 5

66
• Position the footrest so that the soothing
unit is upright.
• While flexing the base tubes toward each
other, hook the footrest onto the ends of the base tubes.
• Push the footrest down completely, to the tabs on the base tubes.
• Make sure the small tabs on the left and right base wires are secure in
the base connector holes (see inset). If the small tabs are not secure in
the base connector holes, you have assembled the base incorrectly.
Disassemble all parts and refer back to Assembly Step 1.
AASSSSEEMMBBLLYY
22
Base Tube
Tab
Tab
Base Tube
Soothing
Unit
Footrest
Back View
Base
Connector
Base
Tube
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A.
©2000 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc.
Printed in China 79436pr-0920
79436pr-0920.qrk 9/22/00 11:00 AM Page 6

77
33
• Position the seat back tube above the base assembly. The seat back tube
should bend backward.
• Fit the seat back tube completely onto the base tubes.
AASSSSEEMMBBLLYY
Base
Tube
Base
Tube
Seat Back
Tube
79436pr-0920.qrk 9/22/00 11:00 AM Page 7

88
AASSSSEEMMBBLLYY
• Fit a retainer to the outside of the seat back tube, as shown. Make sure
the socket in the retainer is upright.
• Insert a screw through the hole in the seat back tube, base tube and
into the inside of the retainer.
• Tighten the screw with a Phillips screwdriver. Do not over-tighten.
• Repeat this procedure to assemble the other retainer to the other side
of the seat back tube.
• Pull up on the seat back tube to be sure it is secure. If you can remove
either end of the seat back tube, you have not assembled it correctly.
Remove the screws, re-read and repeat Assembly steps 3 and 4.
Pull Up
Retainer
Socket
Socket
Retainer
44
79436pr-0920.qrk 9/22/00 11:01 AM Page 8

99
AASSSSEEMMBBLLYY
• Position the pad with the ruffle up.
• Fit the upper pocket on the back of the pad onto the seat back tube .
• Lift the footrest. Fit the lower pocket on the back of the pad onto the
footrest . Lower the footrest.
A
B
55
Seat Back
Tube
Footrest
Pad
79436pr-0920.qrk 9/22/00 11:01 AM Page 9

1100
Hint: Twist the ends of the rings apart to attach them to the mirror or paddle.
• The toy bar is removable. Simply pull out to remove.
• Fit the toy bar plugs into
each retainer socket.
• Snap the mirror and the paddles
to the toy bar.
• The rings can be attached to the
mirror and one of the paddles,
as shown.
88
Rings
Plugs
Retainer
Socket
Retainer
Socket
Toy Bar
Mirror
Paddle
66
AASSSSEEMMBBLLYY
79436pr-0920.qrk 9/22/00 11:01 AM Page 10