Fisher-Price L3891 User manual

www.fisher-price.com.au
L3891
IMPORTANT!
KEEP INSTRUCTIONS
FOR FUTUREREFERENCE.

2
Prevent serious injury or death from falls
or sliding out:
• Always use the restraint system for the
upright and reclined positions of the seat.
Adjust restraint to fit your child snugly.
The tray is not designed to hold the child
in the chair.
• It is recommended that only children
capable of sitting upright unassisted use
the upright position of the high chair.
• Position the high chair away from steps,
hot surfaces, electrical cords and other
items that may cause injury to the child.
• Always leave wheels locked.
• Always keep child in view while in
high chair.
• Never leave child unattended.
• Follow the manufacturer’s instructions.
WARNING
CAUTION
This package contains small parts in
its unassembled state. Adult assembly
is required.
2
IMPORTANT! Place the high chair on a level, stable surface
away from electrical flexes. Be sure to keep electrical flexes
out of child's reach.
• Please read these instructions before assembly and use of
this product.
• Adult assembly is required.Tool needed for assembly:
Phillips screwdriver (not included).
• Weight limit: 22,7 kg (50 lbs).
• Product features and decorations may vary from photos.
Consumer Information
• Australia: Mattel Australia Pty. Ltd., 658 Church Street,
Locked Bag #870, Richmond, Victoria 3121 Australia.
Consumer Advisory Service 1300 135 312.
•
New Zealand: 16-18 William Pickering Drive, Albany 1331,
Auckland.
•
Asia: Mattel East Asia Ltd, Room 1106, South Tower,
World Finance Centre, Harbour City, Tsimshatsui,
HK, China.
•
Malaysia: Diimport & Diedarkan Oleh: Mattel SEA Ptd
Ltd. (993532-P) Lot 13.5, 13th Floor, Menara Lien Hoe,
Persiaran Tropicana Golf Country Resort, 47410 PJ.
Tel: [phone], Fax: [phone].

3
Parts
Front Base
Footrest
Back Base
2 Frames
Hinge Rod
2 Seat Bottom Tubes
Pad
Seat Bottom
Seat Back
Base TrayFood Tray
Note: Tighten or loosen all screws with a Phillips screwdriver.
Do not over-tighten the screws.
Shown Actual Size
#8 x 1,9 cm Screws - 8 #10 x 2,2 cm Black Screws - 7
Teether Toy

4
Assembly
1
•Place the seat bottom face down on a flat surface.
•At an angle, fit the footrest to the seat bottom, as shown.
Seat Bottom
Footrest
•Slide a seat bottom tube through each set of plastic rings
on the seat bottom.
2
Plastic Rings
Seat Bottom Tubes
Plastic Rings
IMPORTANT! Before assembly and each use, inspect this
product for damaged hardware, loose joints, missing parts or
sharp edges. DO NOT use if any parts are missing or broken.
Contact Mattel for replacement parts and instructions if
needed. Never substitute parts.
•Align the holes in the plastic rings and the seat bottom tubes.
•Insert a #8 x 1,9 cm screw through each plastic ring and into
the seat bottom tubes, as shown.Tighten the screws.This may
require extra force.
•Push the seat bottom tubes back and forth to be sure they
are secured to the seat bottom. If the seat bottom tubes
move, you have probably not fastened them properly. Remove
the screws and check to be sure the screw holes in the
seat bottom tubes and seat bottom plastic rings are aligned.
Replace and tighten the screws.
3

5
Assembly
4
•Insert two #10 x 2,2 cm black screws through the
footrest and into the seat bottom.Tighten the screws.
Insert Screws Here
6
Hinge
•Turn the seat assembly face down.
•Insert the hinge rod through the hinge on the seat back
and seat bottom, as shown.
•Insert a #10 x 2,2 cm black screw into the hinge rod.
Tighten the screw.
•Set the seat assembly aside for Assembly step 10.
Hinge Rod
5
•Turn the seat bottom assembly upright.
•Fit the seat back pins into the slots in the top side of the
seat bottom assembly.
Seat Back Pins
Slot
Slot
Frame Leg
7
•Pull the frame leg out on each frame to open. Make sure it
"clicks" into place.

6
Assembly
•Position a frame so that the
decorated side is outward.
•Insert the back frame legs into the back base.
•Fit a screw retainer over a hole in the back base, as shown.
•Insert a #10 x 2,2 cm black screw through the screw
retainer and back base. Tighten the screw.
•Repeat this procedure to fasten the other frame back leg to
the other side of the back base.
Hint: The #10 x 2,2 cm black screws may have been
assembled to the screw retainers.
Frame Decorated Side
Frame Back Legs
Back Base
Screw Retainers
8
•While pressing the levers on the seat height adjusters,
lift them to position 4 on the frame front legs, as shown.
Seat Height Adjusters
Position 4
Press Lever
9
•Fit the seat assembly between the two frames.
•Insert the seat bottom tubes into the sockets in each seat
height adjuster.
Hints:
•Be sure the seat height adjusters are in the same position
(position 4).
•You may need to push the frames apart slightly to fit the
seat bottom tubes into the seat height adjuster sockets.
Seat Assembly
Sockets
Seat Bottom Tubes
4
10

7
Assembly
•Fit the frame front legs onto the front base.
•Fit a screw retainer over the hole in a front leg.
•Insert a #10 x 2,2 cm black screw through the screw
retainer and front leg.Tighten the screw.
•Repeat this procedure to fasten the other end of the front
base with the remaining screw retainer and
#10 x 2,2 cm black screw.
Hint: The #10 x 2,2 cm black screws may have been
assembled to the screw retainers.
Front Base
Screw Retainers
Seat Height Adjusters
•From the back and bottom of the assembly,insert a #8 x 1,9 cm
screw through both seat height adjusters and the ends of
the seat bottom tube.Tighten the screws.This may require
extra force.
Seat Bottom Tube Ends
13
•Squeeze the restraint release tabs together.
•Remove the ends of the restraint system from the peg.
PRESS
14
11
PUSH PUSH
•Push each seat height adjuster to be sure they are
completely on the seat bottom tubes.
•Insert a #8 x 1,9 cm screw through each seat height
adjuster and the ends of the seat bottom tube.Tighten
the screws.This may require extra force.
PRESS
12

8
Assembly
•Remove both shoulder straps from the seat back.
•Remove the crotch strap from the seat back.
Shoulder Straps
Crotch Strap
15
•Fit the pocket on the top of the pad onto the seat back.
16

9
Assembly
•From behind the product, attach the end of the crotch
strap to the peg.
20
Clips
•Fit the clips on the front edge of the pad onto the
seat bottom.
•Hook the elastic loops on each side of the pad onto the
tabs in the seat back.
17
18
Shoulder
Straps Up
Crotch
Strap Down
Lowest Slot
Hint: Do not unbuckle the restraint system. It is easier to
attach or re-attach it to the product if it is buckled.
•Grasp the restraint system so that the shoulder straps are up
and the crotch strap is down.
•Insert the end of the crotch strap through the lowest slot
in the pad and the seat back.
•From behind the product, attach the end of the crotch strap
to the peg.
19

10
Smaller Baby
•Insert the ends of
the shoulder straps
through the lower slots in the pad.
•From behind the product, attach the ends of the shoulder
straps to the peg.
Assembly
Larger Baby
•From the front of
the product, insert
the ends of the shoulder
straps through the upper slots in the pad and seat back.
•From behind the product, attach the ends of the shoulder
straps to the peg.
21 22