Fisher-Price SOOTHING DREAMS 71597 User manual

w
w
w.
fi
s
he
r
-p
r
i
c
e
.
c
o
m
Model Number: 71597
For proper set-up and use, please read these instructions.
Please keep this instruction sheet for future reference,
as it contains important information.
Transmitter is electrically powered.
Remote control receiver is powered by the AC adaptor (included, plugs
into standard household outlets 120V AC). Remote control receiver
also runs on battery power (9V alkaline battery - not included).
Requires one PR12 light bulb (included).
An adult must install the battery (if used) and replace the light bulb.
Tool needed for battery installation and
light bulb replacement: Phillips screwdriver.
Soothing Dreams
Monitor
with Remote Control
TM

2

This product cannot replace
responsible adult supervision.
CAUTION
IMPORTANT!
3
• This product is not intended to be used as a medical monitor
and its use should not replace adult supervision.
• Test sound reception of remote control receiver before first-time
use and whenever you change location of transmitter.
• To prevent entanglement:
- Never place transmitter in a crib or playpen. Keep transmitter
and remote control receiver out of baby’s reach.
- Never use extension cords with the AC adaptor.
• Never use transmitter or remote control receiver near water
(ie.: bathtub, sink, laundry tub or wet basement, etc.).
• Always use transmitter and remote control receiver where there is
adequate ventilation.To prevent overheating, keep transmitter and
remote control receiver away from heat sources such as radiators,
heat registers, direct sunlight, stoves, amplifiers, or other appliances
which produce heat.
• Never attempt to modify this product.
Occasionally a consumer may experience a problem with one of our
products. If this should happen, please call us toll-free, rather than
return this product to the store. Usually, we can solve the problem
over the telephone or send you replacement parts.
Please call Fisher-Price® Consumer Relations, toll-free at
1-800-432-KIDS, between 8 AM - 6 PM EST, Monday through Friday.
Hearing-impaired consumers using TTY/TDD equipment,
please call 1-800-382-7470.
Or write to:
Fisher-Price® Consumer Relations
636 Girard Avenue
East Aurora, New York 14052
Consumer Information

Remote Control Receiver
Battery Installation (Optional)
4
Battery
Compartment Door
• Locate battery compartment door on back of remote control receiver.
• Loosen screw in battery compartment door with a Phillips screwdriver.
Lift to remove battery compartment door.
• Snap terminals of a fresh, 9V alkaline battery into remote control
receiver connectors.
• Replace battery compartment door and tighten screw.
Do not over-tighten.
Battery Tips
• Remove the battery during long periods of non-use. Always
remove an exhausted battery from the product. Battery leakage
and corrosion can damage this product. Dispose of battery safely.
• Do not dispose of the battery in a fire.The battery may explode
or leak.
• Never short circuit the battery terminals.
• A non-rechargeable battery is not to be recharged.
• Only a battery of the same or equivalent type as recommended in
the “Battery Installation” instructions is to be used.
• If a removable rechargeable battery is used, it is only to be charged
under adult supervision.
• A rechargeable battery is to be removed from the product before
it is charged.
• If you use a battery charger, it should be examined regularly for
damage to the cord, plug, enclosure and other parts. Do not use
a damaged battery charger until it has been properly repaired.
9V (6LR61)
SHOWN ACTUAL SIZE

Testing Sound Reception
5
Test transmitter transmission and
remote control receiver reception.
Place transmitter in room in which
you intend to use it. Rotate transmit-
ter power/volume dial to turn power
on. Turn on a radio.
Place remote control receiver in
room in which you intend to use it.
Rotate power/volume dial to turn
power on. Adjust remote control
receiver location.
• Variable light display lights when
sound is received by remote
control receiver:
- One or two dots light for
shallow sounds.
- Three or more dots light for
louder sounds.
• If you experience interference
(buzzing or static, etc.) while using
one channel setting, switch both
units to other channel. Selecting
a channel is usually a one time
adjustment.
Hint: All four dots in remote control receiver variable light display light:
- If you turn remote control receiver power on before transmitter power.You will
also hear static noise.Turn volume down and turn transmitter power on.
- If the remote control receiver is too far away from the transmitter. Move the remote
control receiver closer to the transmitter.
- If loud sounds are transmitting.
Power
Indicator
Power/Volume Dial
Power
Indicator
Power/Volume
Dial
Adjust
Channel
BUZZZZ
STATIC

Setup & Use
6
8
3
2
7
Back View
Transmitter
1
Transmitter
4
6
5
1
Remote Control
Receiver

IMPORTANT! Test sound reception of this monitor before first time
use and whenever you change location of transmitter (see page 5).
Set transmitter channel switch to same channel as remote
control receiver.
Place transmitter in same room with child. Point microphone
directly toward crib or play area.
Unwrap and fully extend power cord for best transmission.
Insert power cord plug into wall outlet.
Rotate transmitter power/volume dial to turn power on.
Power indicator lights.
Choose a soothing mode:
Light only
Light and Music
Light and Nighttime Nature Sounds
Choose a light mode:
Ceiling Light Show
Night Light
If you chose Ceiling Light Show ( ), adjust projector
on the back of transmitter so that it projects on ceiling
over baby’s crib.
Press soothing button on transmitter to activate your
selection. Rotate power/volume dial to adjust volume.
Light/music/nature sounds will turn on for about five
minutes and then automatically turn off. If you’d like to
immediately turn off light/music/nature sounds, press
soothing button on transmitter again.
1
2
3
5
Setup & Use
Hint: If you do not want light/music/nature sounds on after presetting
transmitter, do not press soothing button on transmitter.
7
SFX
4
6
7
8

Setup & Use
9
8
10
11

Setup & Use
Place remote control receiver where you will see or hear it.
Unwrap and fully extend AC adaptor cord for best reception.
Insert AC adaptor jack into remote control receiver socket and
plug into wall outlet.
Note: To use a 9V alkaline battery for power source, refer to
“Remote Control Receiver Battery Installation” instructions
on page 4.
Rotate remote control receiver power/volume dial to turn
power on. Power indicator lights. Rotate power/volume dial
to adjust volume.
9
11
9
10
Note: AC adaptor is 120 VAC, 60Hz, 3W input; 6 VDC 100mA output;
center positive polarity; plug OD is 5.5 mm, plug ID is 1.5 mm.

Setup & Use
10
Nature
Sounds
• To soothe baby, press and hold soothing button (Soothe) on remote
control receiver for about two seconds. Your baby enjoys what you
have selected.
• Light/music/nature sounds will turn off after approximately five minutes.
To turn back on, simply press and hold soothing button (Soothe) on
remote control receiver for about two seconds.
IMPORTANT! It takes a few seconds for the transmitter to receive a signal
from the remote control receiver. Be sure to press and hold the soothing
button on the remote control receiver for about two seconds.
Ceiling Light
Show
Night Light Night Light
with Music or
Nature Sounds
Ceiling Light
Show with Music
or Nature Sounds
Nature
Sounds