Fisher-Price 71599 User manual

w
w
w.
fi
s
he
r
-p
r
i
c
e
.
c
o
m
Model Number: 71599
For proper setup and use, please read these instructions.
Please keep this instruction sheet for future reference,
as it contains important information.
Transmitter is electrically powered.
Includes one AC adaptor to power receiver (plugs into
standard household outlets –120V AC). Receiver also runs on battery
power (3.6V, 400mAH nickel cadmium rechargeable battery – included).
Adult assembly is required to install the battery.
Tool needed for battery installation:
Phillips screwdriver (not included).
Vibrating
Monitor

This product cannot replace
responsible adult supervision.
CAUTION
IMPORTANT!
2
• This product is not intended to be used as a medical monitor
and its use should not replace adult supervision.
• Test reception of receiver before first-time use and whenever you
change location of transmitter.
• To prevent entanglement:
- Never place transmitter in a crib or playpen. Keep transmitter
and receiver out of baby’s reach.
- Never use extension cords with the AC adaptor or the transmitter
power cord.
• Never use transmitter or receiver near water (ie.: bathtub, sink,
laundry tub or wet basement, etc.).
• Always use transmitter and receiver where there is adequate
ventilation.To prevent overheating, keep transmitter and receiver
away from heat sources such as radiators, heat registers, direct sun-
light, stoves, amplifiers, or other appliances which produce heat.

Receiver Battery Installation
3
Battery
Compartment Door
• Locate battery compartment door on back of receiver.
• Loosen screw in battery compartment door with a Phillips screw-
driver. Remove battery compartment door.
• Plug battery connector into receiver connector.
• Replace battery compartment door. Tighten screw with a
Phillips screwdriver.
Battery Tips
• Remove the battery during long periods of non-use. Always
remove an exhausted battery from the product. Battery leakage
and corrosion can damage this product. Dispose of battery safely.
• Do not dispose of battery in a fire.The battery may explode or leak.
• Never short circuit the battery terminals.
• A non-rechargeable battery is not to be recharged.
• Only a battery of the same or equivalent type as recommended in
the “Battery Installation” instructions is to be used.
• If a removable rechargeable battery is used, it is only to be charged
under adult supervision.
• If you use a battery charger, it should be examined regularly for
damage to the cord, plug, enclosure and other parts. Do not use
a damaged battery charger until it has been properly repaired.
• Use only the provided AC adaptor to charge the battery.
Your Fisher-Price® Vibrating Monitor includes a rechargeable battery.
Before first-time use, you will need to charge the battery (see next page).
Hint: If battery connector will not plug into receiver connector, turn it over
and try again. Do not force the battery connector into the receiver connector.
Battery Connector
Receiver Connector

Charging the Receiver Battery
• Insert AC adaptor jack into receiver socket and then plug into
wall outlet.
• Charge the rechargeable battery for 10-12 hours. Do not overcharge
your battery.
Battery Disposal
Nickel cadmium batteries contain materials which are harmful to the
environment if not properly disposed. Contact the recycling center in
your community for proper disposal instructions.
Hint: When using the receiver with the AC adaptor, you will be charging
the battery while monitoring your baby!
4
Even with proper care, the rechargeable battery will not last forever.
The life of the rechargeable battery depends on how well you follow
these instructions and the total number of hours it is used. If you
should need to replace the rechargeable battery, a new one can
be purchased at most electronics stores or contact Fisher-Price®
Consumer Relations at 1-800-432-KIDS.

Testing Reception (for Sound)
5
Test transmitter transmission and receiver reception
each time you change location of use.
Place transmitter in room in which
you intend to use it. Rotate transmitter
power switch to turn power on. Power
indicator lights.Turn on a radio.
Place receiver in room in which
you intend to use it. Rotate the
power/volume dial to turn power
on. Power indicator lights. Adjust
receiver location.
• Variable light display lights when
sound is received by receiver:
- One two dots light for
shallow sounds.
- Three or more dots light for
louder sounds.
If you experience interference
(buzzing or static, etc.) while using
one channel setting, switch both
units to other channel. Selecting
a channel is usually a one time
adjustment.
Hint: All five dots in receiver variable light display light:
- If you turn receiver power on before transmitter power. You will also hear
static noise.Turn volume down on receiver and turn transmitter power on.
- If the receiver is too far away from the transmitter. Move the receiver closer
to the transmitter.
- If loud sounds are transmitting.
Adjust
Channel
BUZZZZ
STATIC
Power
Indicator
Power
Switch
Power
Indicator
Power/Volume
Dial

Testing Reception (for Vibrations)
6
Place transmitter in room in which
you intend to use it. Rotate transmitter
power switch to turn power on. Power
indicator lights.Turn on a radio.
Power
Indicator Power
Switch
Clip receiver to your clothing (where
you will feel vibrations). Walk to the
furthest point of use. Rotate receiver
power/volume dial to turn power
on. Power indicator lights. Now, press
the vibrations button.Vibrations
ready indicator lights.
• When sound is received, vibrations
begin and variable light display
lights on receiver.
• To turn off vibrations, press
vibrations button.Vibrations
ready indicator turns off.
• If you experience interference
(vibration) when it is obvious
that no sound is transmitting
while using one channel setting,
switch both units to other channel.
Selecting a channel is usually a
one time adjustment.
Vibrations
Button
Vibrations
Ready
Indicator
Power
Indicator
Power/Volume
Dial
Power
Indicator Power
Switch
Test transmitter transmission and receiver reception
each time you change location of use.
Hint: You can also place the
receiver in your pocket.
Vibrations Button

Setup For Sounds ‘n Lights Use
2
6
3
5
7
1
4
7
1

IMPORTANT! Test sound reception of this monitor before first time
use and whenever you change location of transmitter (see page 5).
Set transmitter channel switch to same channel as receiver.
Place transmitter in same room with child. Point microphone
directly toward crib or play area.
Unwrap and fully extend power cord for best transmission.
Plug transmitter power cord into wall outlet.
Slide transmitter power switch to turn power on.
Power indicator lights.
Place receiver where you will see or hear it.
If you will be using receiver near a wall outlet, we recommend
that you use the AC adaptor. Unwrap and fully extend AC
adaptor cord for best reception. Plug AC adaptor cord into
wall outlet.
Rotate receiver power/volume dial to turn power on. Power
indicator lights. Rotate power/volume dial to adjust volume.
1
2
3
4
5
6
7
8
If you have any questions about this product:
In Canada, call 1-800-567-7724, or write to: Mattel Canada Inc., 6155 Freemont Blvd.,
Mississauga, Ontario L5R 3W2.
In Great Britain, telephone [phone].
In Australia, Mattel Australia Pty. Ltd., 658 Church Street, Locked Bag #870,
Richmond,Victoria 3121 Australia. Consumer Advisory Service 1-800-800-812
(valid only in Australia).
Note: AC adaptor is 120 VAC, 60Hz, 3W input; 6 VDC 100mA output;
center positive polarity; plug OD is 5.5 mm, plug ID is 1.5 mm.

Setup For Vibrations Use
IMPORTANT! Test reception of this monitor before first time use
and whenever you change location of transmitter (see page 6).
Set transmitter channel switch to same channel as receiver.
Place transmitter in same room with child. Point microphone
directly toward crib or play area.
Unwrap and fully extend power cord for best transmission.
Plug transmitter power cord into wall outlet.
Slide transmitter power switch to turn power on.
Power indicator lights.
Clip receiver to your clothing, where you will feel vibrations.
Or, place the receiver in your pocket.
Rotate receiver power/volume dial to turn power on. Power
indicator lights. Rotate power/volume dial to adjust volume
(if you want to hear sounds).
Press the vibrations button. Vibrations ready indicator lights.
1
2
3
4
5
6
7
Hint: Under permitting conditions, the receiver receives sounds (and you
will feel vibrations) up to 1,000 feet away from baby.
9
21
4
3
5
6
“Wah, Wah,
Wah…”
7

Problems & Solutions
6
4
3
10
“Ma, ma, ma.
Da, da, da…”
BUZZZZ
BUZZZZZ
BUZZZZZ
2
1
Circuit Breaker
5
“That doesn’t
sound right. Maybe
we should check the
transmitter.”