Flash Furniture SDA-AD608001-NAT-GG User manual

Thank you for your purchase!
HANGING HAMMOCK
CHAIR WITH STAND
ASSEMBLY INSTRUCTIONS
Before You Begin:
Please identify all component parts and hardware pieces required before you begin. Carefully remove all of the
components from the packaging and set aside for assembly. Assemble on a soft surface to prevent scratching
during assembly.
Caution:
Tighten all components securely before use. Failure to do so may result in personal injury.
DO NOT use any sharp objects to open plastic wrapped components as damage to product or components may
result.
Warning:
CHOKING HAZARD - Small Parts. Adult Assembly Required.
DO NOT ALLOW CHILDREN TO CLIMB ON FURNITURE
Serious or fatal injuries can occur from furniture tipping over. You must install Tipping Restraint Hardware (where
included) to help prevent the unit from tipping and causing accidental injury, instability, death or damage. The
tipping restraint is intended only as a safety measure, it is not a substitute for proper adult supervision.
To help prevent furniture from tipping over it must be permanently attached to the wall. Anti-Tip Safety Wall
Straps suitable for the unit weight and wall materials (if not included) should be purchased and installed.
……………………………………………………………………………………………………………………………………
Customer Service Email: Cust[email protected] | Phone: [phone]
SDA-AD608001-NAT-GG / SDA-AD608001-GY-GG

Have a Question/Concern?
Quality products and first-class customer service are the cornerstone of long-lasting
consumer relationships. We strive toward excellence in all we do and want you to be
completely satisfied with your purchase.
Please contact our exceptional Customer Experience Agents at the email address or
phone number shown below to assist you with any product questions or issues
before requesting a return.
We look forward to serving you in a friendly, efficient manner to resolve any issues you
may have.
Customer Service Email: [e-mail]
Customer Service Phone: [phone]
Our Warranty Statement
This warranty covers manufacturing defects associated with your new product. The
product is warranted from the original purchase date and to the original purchaser
for normal usage, according to the below-referenced specifications and limitations.
• Non-moving metal parts are warranted for 5 years.
• Component parts including pneumatic cylinder, control mechanism, base and
casters are warranted for 2 years.
• All other items are warranted for 1 year.
Normal usage means use in compliance with the restrictions and weight limits specified
for the product. In the absence of product-specific restrictions and weight limits,
normal usage means use for no more than forty hours per week by persons weighing
250 lbs. or less. Coverage terminates if the product is sold or otherwise transferred.
Repairs made by parties other than Belnick also void this warranty.
This warranty will not cover: (1) labor, freight, or damage from misuse, abuse,
negligence, alteration, assembly, installation, attachments, accident, vandalism, acts
of nature or any other event beyond the control of Belnick; (2) tearing, scratching,
scuffing, or blemishing of leather or fabric; (3) cosmetic damage that may result
from normal usage; (4) damage attributable to use by persons exceeding specified
weight limits or commercial use exceeding forty hours per week; or (5) rust or other
damage caused by exposure to moisture. The user assumes all risk of injury
resulting from use of this product. Liability for incidental or consequential damage
is excluded. Some states do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation or exclusion may not apply to you.
……………………………………………………………………………………………………………………

Part Drawing Description QTY
A
Support connector 1
B
Chair 1
C Support legs 4
D Support pole 1
E
Screw M8*57
1
F
Screw M6*15
4
G Nut 1
H Wrench 1
I Allen Wrench 1
J Clevis Pin 1
K Spring 1
L Chain 1
M Anchor Shackle 1
……………………………………………………………………………………………………………………
Parts

Step 1
Attach Support Legs (Part C) to
Support Connector (Part A) using (4)
M6*15 Screws (Part F). Tighten using
Allen Wrench (Part I). Bring to the
upright position.
NOTE: Ensure Feet are facing down.
C
Support Legs
Support Connector
Step 2
Attach Support Pole (Part D) to
Support Connector (Part A)
using (1) M8*57 Screw
(Part E) and (1) Nut (Part G).
Tighten by placing the
Wrench (Part H) on the Nut
and using the Allen Wrench
(Part I) to tighten the screw.
Step 3
Insert the Clevis Pin (Part J) into the top of the
Support Pole. Insert one end of the Spring
(Part K) into the Bolt then attach the end of
the Chain (Part L) onto the other end of the
Spring.
Remove the bolt from the Anchor Shackle (Part M) and
insert through the link in the Chain.
Step 4
Lift the Chair (Part B) and line the top U Bracket
between the sides of the Anchor Shackle (Part M).
Insert Bolt removed in Step 3 and securely tighten the
nut using the Wrench and Allen Wrench as described
in Step 2.
……………………………………………………………………………………………………………………………
Wrench
N ut
Support pole
M8*57 Screw
Allen Wrench