Flash Furniture ZG-035-GY-GG User manual

Thankyouforyourpurchase!
ZG-035-GY-GG / ZG-035-OAK-GG
50 LBS
ASSEMBLY INSTRUCTIONS
Before You Begin:
Please identify all component parts and hardware pieces required before you begin. Carefully remove all of the
components from the packaging and set aside for assembly. Assemble on a soft surface to prevent scratching
during assembly.
Caution:
Tighten all components securely before use. Failure to do so may result in personal injury.
DO NOT use any sharp objects to open plastic wrapped components as damage to product or components may
result.
Warning:
CHOKING HAZARD - Small Parts. Adult Assembly Required.
DO NOT ALLOW CHILDREN TO CLIMB ON FURNITURE
Serious or fatal injuries can occur from furniture tipping over. You must install Tipping Restraint Hardware (where
included) to help prevent the unit from tipping and causing accidental injury, instability, death or damage. The
tipping restraint is intended only as a safety measure, it is not a substitute for proper adult supervision.
To help prevent furniture from tipping over it must be permanently attached to the wall. Anti-Tip Safety Wall
Straps suitable for the unit weight and wall materials (if not included) should be purchased and installed.
End
Table

Safety and Care Advice
Important – Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
the following pages.
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Handy Hints
• Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the bolts
• Regularly check and ensure
tightend properly.
• During assembly do not stand
or put weight on the product,
this could cause damage.
• Assemble the item as close
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
• Parts of the assembly will be
easier with 2 people.
• To reduce
the likelihood of
damaging your
product please
ensure that your
power drill is set on a low torque
setting.
WARNING
In order to help prevent overturning –
To help prevent product toppling over please follow the below steps:-
Do not open more than one drawer at a time
Do not place heavy items in the top drawers
Do not place heavy items on top of the furniture, unless the furniture has been
designed for this purpose
You will need to provide wall plugs and screws applicable for your wall type
1
!
• Remove all fittings from the
to its final position (in the same
unit or your floor.
That all bolts and fittings are
please follow these instructions
Do not allow children to climb or hang on the furniture
Use the anti tip stap or wall fixing method provided (if applicable)
Please note that only the anti tip strap is provided.

Components - Fittings
Note:
may be supplied than are required.
Male Camlock x 8
A
D
8*65mm Screw x 4
G
Panel Support x 8
J
Ø30mm Sticker x 4
Female Camlock x 8
B
E
bo x 4
H
C
Wood Dowel x 4
F
I
Protective Feet x 4
Tools required
Phillips screwdriver
(medium & large)
Ruler - Use this ruler to help correctly identify the screws
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170
The screws length is measured from the head to the point (30mm screw shown).
Please check you have all the panels listed below
The quantities below are the correct amount to complete the assembly. In some cases more fittings
Allen Key x 1
3.5*14mm Screw x 64
K
Triangular support x 8

Using Camlocks
12
DO NOT OVER TIGHTEN.
NE PAS SERRER EXCESSIVEMENT.
34
4
Step 1
Step 3
Step 2
Step 4
Connect the male
camlock as diected in
the assembly instructions
using a scewdriver.
Push the male camlock
into the entry hole.
Insert the female
camlock as shown in the
instruction.
Note：ensure that the
arrow on the top of the
camlock points towards
the entry hole for the
male camlock.
Turn the female camlock
clockwise with a
screwdriver.
You should feel a click
when the camlock is
locked in place.
The joint is now secure.

Assembly Instructions
1
2
2
1
3
4
5
Center Shelf
Top Panel
Bottom Panel
Front Leg
Rear Leg
Rear Leg
Front Leg
Triangular support
Triangular support
Triangular support
Triangular support
Triangular support
Triangular support

Assembly Instructions
Step 1
Step 2
A
X2
A
C
C
C
C

Assembly Instructions
Step 3
Step 4
B
B
E
E
D
D
F
1 2 3

Assembly Instructions
Step 5
Step 6
E
E
D
D
B
B
F
1 2 3
5
A
A
A
A

Assembly Instructions
Step 7
Step 8
B
B
B
B
1 2 3
1
2
1
23
4
5
3
J
J
J
J

Assembly Instructions
Step 9
Step 10
X8 I
G
HH
HH
K
K
K
X4
H
X4
HX4
H
X4
H
2
11
5
4
3
1
5
X4
K
H
H
HH

Assembly Instructions
Step 11
Step 12
Assembly is complete.
K
K
X4
H
X4
HX4
H
X4
H
2
11
5
4
3
1
5
X4
K
H
H
HH