Flash Furniture SL-BK4-T-B-GG User manual

Thank you for your purchase!
PLATFORM BED FRAME
ASSEMBLY INSTRUCTIONS
Before You Begin:
Please indentify all component parts and hardware pieces required before you begin. Carefully remove
all of the components from the packaging and set aside for assembly. Assemble on a soft surface to
prevent scratching during assembly.
Caution:
Tighten all components securely before use. Failure to do so may result in personal injury.
DO NOT use any sharp objects to open plastic wrapped components as damage to product or
components may result.
Warning:
CHOKING HAZARD - Small Parts. Adult Assembly Required.
DO NOT ALLOW CHILDREN TO CLIMB ON FURNITURE
Serious or fatal injuries can occur from furniture tipping over. You must install Tipping Restraint Hardware (where
included) to help prevent the unit from tipping and causing accidental injury, instability, death or damage. The
tipping restraint is intended only as a safety measure, it is not a substitute for proper adult supervision.
To help prevent furniture from tipping over it must be permanently attached to the wall. Anti-Tip Safety Wall Straps
suitable for the unit weight and wall materials (if not included) should be purchased and installed.
................................................................................................................................................................
Customer Service Email: [email protected] | Phone: [phone]
SL-BK4-T-B-GG / SL-BK4-T-BK-GG / SL-BK4-T-DG-GG / SL-BK4-T-LG-GG / SL-BK4-F-B-GG / SL-BK4-F-BK-GG SL-
BK4-F-DG-GG / SL-BK4-F-LG-GG / SL-BK4-Q-B-GG / SL-BK4-Q-BK-GG / SL-BK4-Q-DG-GG / SL-BK4-Q-LG-GG SL-
BK4-K-B-GG / SL-BK4-K-BK-GG / SL-BK4-K-DG-GG / SL-BK4-K-LG-GG
500
LBS 600
LBS
600
LBS
900
LBS
900
LBS
TWIN SIZE FULL SIZE QUEEN SIZE KING SIZE
400
LBS
400
LBS

Have a Question/Concern?
Qualityproducts andfirst-class customer service are the cornerstone of long-lasting
consumer relationships. We strive toward excellenceinallwedoandwantyoutobe
completely satisfied with your purchase.
Please contact our exceptional Customer Experience Agents at the emailaddressor phone
number shown below to assist you with any product questionsorissuesbeforerequesting
a return.
We look forward to serving you in a friendly, efficientmannertoresolveanyissuesyoumay
have.
Customer Service Email: [email protected]
Customer Service Phone: [phone]
For warranty information, please visit www.belnick.com

PLATFORM BED FRAME
INSTRUCTION
2
KK
D
B
C
A
LMN
L
G
HG
I
F
M
N
L
I
1
3 4
Components
AHeadboard
BHeadboard
Side Legs
1pc
2pcs
CHeadboard
Middle Leg
DFootboard1pc
1pc
ESiderails
FMiddle Brace
4pcs
1pc
GMiddle
Cross Beam
HMiddle Leg
2pcs
1pc
IMiddle Brace Feet
JSlats 2pcs
28pcs
KBed Legs
LWasher
f 8
2pcs
11pcs
MScrew
f 8*40
NAllen Wrench
11pcs
1pc
OOuter Slat
Holders
PMiddle Slat
Holders
28pcs
14pcs
STEP 1: Attach Headboard Side Legs
(Part B) and Headboard Middle Leg
(Part C) to Headboard (Part A) using
(6) Washers (Part L) and (6) 8*40
Screws (Part M). Tighten withAllen
Wrench (Part N)
STEP2: Insert Bed Legs (Part K) into Footboard
(Part D) and turn clockwise to tighten.
Note: Screws preassembled
on the footboard
STEP 3: Attach Middle Cross Beam (Part
G) to Middle Leg (Part H) using (2)
Washers (Part L) and (2) 8*40 Screws
(Part M). Tighten with Allen Wrench (Part
N)
STEP 4: Attach Middle Brace (Part
F) to Middle Brace Feet (Part I)
using (2) Washers (Part L) and (2)
8*40 Screws (Part M). Tightenwith
Allen Wrench (PartN)
NOTE: Ensure
brackets face
outward with slots
point up.

MN
L
G
F
H
I
G
I
J
P
JO
5 6
7 8
9 10
E
E
E
E
E
E
E
E
Note: Screws preassembled
on the leg Note: Screws preassembled on the siderail
STEP 5: Attach Middle Brace (Part F) toMiddle
Cross Beam (Part G) using (1) Washer (PartL) and
(1) 8*40 Screw (Part M). Tighten with Allen Wrench
(Part N)
STEP 6A: Remove preassembled screws from middle leg. Attach Middle
Cross Beam (Part G) to Middle Headboard Leg using preassembled screws.
STEP 6B: Remove preassembled
screws from Footboard. Attach
Middle Brace to Footboard (PartD)
using preassembled screws.
STEP 7: Remove remaining preassembled screws from Headboard
Side Legs and Footboard. Attach Siderails (Part E) to Headboard and
Footboard using preassembled screws.
STEP 8: Loosen preassembled screws from Siderails (Part E). Insert
screws into the slots of the Middle Legs then tighten screws.
STEP 9: Insert (28) Slats (Part J) into the left and right sides of the Middle
Slat Holders (Part P). Insert Slats into Outer Slat Holders (Part O). Push
down on slat holders to secure.
STEP 10: Ensure all screws and slats are secure.