Flash Furniture NAN-JN-2824S-GG User manual

NAN-JN-2824S-GG

ASSEMBLYOVERVIEW
2
Desktop maximum
weight capacity
=
110 lbs
Keyboard tray
maximum
weight capacity
=
sbl10
5 10
9
1
2
6
12
7
13
8
3
4

PARTSLIST
#DESCRIPTION QTY.
1 Back Leg Piece 2
2Front Leg Piece 2
3Upper Leg Frame 2
4 Lower Leg Frame 2
3
THE PART NUMBER CAN BE FOUND ON THE SIDE OF THE PART, EITHER STAMPED OR ON A STICKER.
ITEMS ARE NOT SHOWN TO SCALE.
5
6
Back Upper Bar 1
Front Upper Bar 1
7
8
1
2
9
Lower Bar
10
Support Bar
1
Tray Support Left
Tray Support Right 1

4
EXTRA HARDWARE INCLUDED FOR YOUR CONVENIENCE. ITEMS ARE NOT SHOWN TO SCALE.
HARDWARE LIST
PARTS LIST (CONT’D)
- READ THE INSTRUCTION MANUAL BEFORE ASSEMBLING.
- REMOVE ALL PIECES BEFORE BEGINNING INSTALLATION.
- OPEN THE HARDWARE AS NEEDED .
- ASSEMBLE IN AN AREA WITH PLENTY OF SPACE.
- READ EACH STEP BEFORE BEGINNING CONSTRUCTION.
- HAVE A SCREWDRIVER BEFORE YOU BEGIN ASSEMBLING
(NOT INCLUDED).
- NEVER FORCE THE SCREWS OR FITTINGS.
- KEEP THIS MANUAL FOR FUTURE REFERENCE.
- TIGHTEN ALL THE SCREWS EVERY 6 MONTHS.
CLEANING AND CARE
- CLEAN SURFACES WITH A DRY OR DAMP CLOTH.
- DO NOT USE ABRASIVE CLEANERS.
- DO NOT USE A POWER DRILL.
#DESCRIPTION QTY.
12 Keyboard Tray 1
13 Desktop Glass 1
A
B
C
D
6
4
12
4
2
4
1
DESCRIPTION
F
G
H
Extra Hardware Set
M6 x 55mm
M6 x 35mm
M6 x 12mm
M6 x 20mm
1
Allen Wrench
M6 x 35mm
M4 x 14mm
QTY.

ASSEMBLY INSTRUCTIONS
5
STEP 1
Back Leg Piece which will be used to attach the Lower Bar (9). Attach the Back and Front Legs using the M6 x 35mm screw
with the nut (A). Repeat with the other set of leg pieces. Make sure not to connect one front piece with another, or a back
piece with a back. Attach the two Lower Leg Frames (4) to the leg pieces using eight M6 x 12mm screws (D).
A x 2
D x 8
H
Extra screw hole in the
back leg piece
1
4
2
BEFORE BEGINNING STEP 2, PLEASE NOTE THE DIFFERENCES BETWEEN THE TWO UPPER BARS
(THE LOWER BAR, WHICH IS NOT SHOWN BELOW, HAS TWO SCREW HOLES TOWARD THE CENTER).
(Part #5) Back Upper Bar
(Part #6) Front Upper Bar
Does not have the two holes underneath
Holes on the top to attach the glass
(go all the way through the bar)
Holes on the side to attach the
keyboard tray supports (go all
the way through the bar)
Holes underneath (not shown) to
attach the support bars (do not
go all the way through the bar)

ASSEMBLY INSTRUCTIONS
6
STEP 2
Align the legs making sure the lower holes in the back legs are on the same side (toward the back of the desk). Attach the
legs to the Lower Bar (7) with two M6 x 55mm screws (B).
H
B x 6
D x 4
These holes should
be on the same side
5
6
8
3
7
B
B
D
D
Attach the Support Bars (8) to the Back Upper Bar (5) and Front Upper Bar (6) with four M6 x 12mm screws (D).
Use four M6 x 55mm screws (B) to attach the Back Upper Bar (5) and Front Upper Bar (6) to the legs and Upper Leg Frames (3).
Make sure to place the Back Upper Bar (5) at the back of the desk.
B

ASSEMBLY INSTRUCTIONS
7
STEP 3
STEP 4
H
C x 4 5
910
6
C
C
C
C
Attach the Left (9) and Right (10) Tray Supports to the Back Upper Bar (5) and Front Upper Bar (6) using four M6 x 35mm
Screws (C).
F x 4
F
F
F
F
12

ASSEMBLY INSTRUCTIONS
8
STEP 5
13
G G
G
G
Attach the Desktop Glass (13) to the Upper Bars using four M6 x 20 mm Screws (G).
G x 4
H