Flash F7100549 User manual
WARNING! The Moving Head 60W Spot has a powerful pan motor. The torque reaction when the
head is panned suddenly can cause the base to move if the fixture is standing unsecured on a
surface. Do not apply power to the Moving Head 60W Spot unless the baase is securely fastened
to a surface or to rigging hardware.
WARNING! Use 2 clamps to rig the fixture. Do not hang the fixture from only one clamp. Lock
each clamp with both 1/4-turn fasteners. Fasteners are locked only when turned a full 90
clockwise.
WARNING! When clamping the fixture to a truss or other structure at any other angle than with
the yoke hanging vertically downwards, use two clamps of half-coupler type. Do not use any type
of clamp that does not completely encircle the structure when fastened.
WARNING! Position or shade the head so that the front lens will not be exposed to sunlight or
any other strong light source from any angle - even for a few seconds. See Figure 2. The Moving
Head 60W Spot lens can focused the sun's rays, creating a potential fire hazard and causing
damage.
IMPORTANT! Do not point strong light output from other fixtures at the Moving Head 60W Spot,
as intense illumination can damaged the display.
WARNING!
User Manual •Instrukcja Obsługi
Figure 2.
Shield or shade the head if necessary.
• Please keep this User Manual for future
user, be sure that they also receive this
instruction booklet.
• Unpack and check carefully there is no
transportation damage before using the
• Before operating, ensure that the voltage
and frequency of power supply match the
• It’s important to ground the yellow/green
conductor to earth in order to avoid electric
shock.
• Disconnect main power before servicing
and maintenance.
•
but always by taking its base.
• Maximum ambient temperature is: 40
Don’t operate it where the temperature is
higher than this.
• In the event of serious operating problem,
carried out by unskilled people can lead to
damage or malfunction. Please contact the
nearest authorized technical assistance
center. Always use the same type spare parts.
• Do not connect the device to any dimmer
pack.
• Do not touch any wire during operation and
there might be a hazard of electric shock.
• To prevent or reduce the risk of electrical
or moisture.
• The housing must be replaced if they are
visibly damaged.
• Do not look directly at the LED light spot
2. SAFETY INFORMATION
1. INTRODUCTION
Moving Head 60W Spot
DMX
Controller DMX 512 DMX 512
LED Moving Head 60W Spot ver.12.2021 •Art No P7100549
•
• Power consumption: 80W
•
•
• TILT range: 202
• Angle: 11
•
5.1 Connecting DMX signal
The connection is performed using cable with
5. CONNECTION
•
•
• 9/11 DMX channel mode.
•
•
•
•
The device is equipped with the following
interfaces:
1
3
22
FEMALE
XLR
GROUND
DMX +
DMX -
MALE
XLR
3
1
CAUTION!
has to be terminated with a terminator. Solder
1
FEMALE
XLR
GROUND
DMX +
DMX -
MALE
XLR
2
3
4
5
1
2
3
45
The unit should be mounted via its screw
holes on the bracket. Always ensure that
the unit is firmly fixed to avoid vibration
and slipping while operating. Always
ensure that the structure to which you are
attaching the unit is secure and is able to
support a weight of 10 times of the unit’s
4. INSTALLATION
3. PRODUCT INFORMATION
weight. Also always use a safety cable that
can hold 12 times of the weight of the unit
when installing the fixture. The equipment
must be fixed by professionals. And it must
be fixed at a place where is out of the touch
of people and has no one pass by or under
it.
The connection is performed using
operated by qualified personnel.
5.2 Voltage specification
Input Voltage Total Power Frequency
220V 80W 50/60Hz
5.3 Connecting power supply
CAUTION! In the case of cable damage do not attempt to repair.
person with appropriate permissions.
Make sure that the power grid supply
parameters are consistent with device
parameters and limitations are not
exceeded.
Using lamp, the change rate of power voltage should be within
± 10%, if the voltage is too high, it will shorten the light’s life; if it’s not
enough, the lamp will be dark. Please restart it after turning off light
for 20 minutes until full-cooling. Frequent switching will reduce the
life span of lamps and bulbs; intermittent using will improve the life
of bulbs and lamps.
User Manual •Instrukcja Obsługi
6. DMX CHANNELS
Display and Menu
Menu UP Down Enter
Menu: Function choice
UP/Down: Function value
Enter:
Addr A001-A512 DMX 512 address code
11 channels
9 channels
Master
Sound
Slow running
SL 1
SEnS 0-99 Sound sensitivity
LEd
dISP Display downward
Display upward
X forward
X backward
rTiL
LED Moving Head 60W Spot ver.12.2021 •Art No P7100549
User Manual •Instrukcja Obsługi
Channel Function Description
1X
2
3
0-139
4
5Strobe
6Dimmer
7
8Auto mode
9
Channel Function Description
1Pan
2
3Tilt
4
5
0-139
6
7Strobe
8Dimmer
9
10
Auto mode
Auto mode 3
Auto Mode 2
110-134 Auto Mode 1
Auto Mode 0
Sound Mode 3
Sound Mode 2
210-234 Sound Mode 1
Sound Mode 0
11
LED Moving Head 60W Spot ver.12.2021 •Art No P7100549
User Manual •Instrukcja Obsługi
OSTRZEŻENIE!
UWAGA! Moving Head 60W Spot
UWAGA!
UWAGA!
UWAGA!
kilka sekund. Patrz rysunek 2
WAŻNE!
Rysunek 2.
2. ZASADY BEZPIECZENSTWA
3. INFORMACJE O PRODUKCIE
4. INSTALACJA
MOVING HEAD 60W SPOT
•
przez wykwalifikowany personel, aby
•
•
•
•
•
•
w dobrze wentylowanym pomieszczeniu,
uszkodzenia spowodowane niestabilnym
•
•
•
•
• TILT: 202
•
•
•
•
•
•
• Waga netto: 3kg
•
•
LED Moving Head 60W Spot ver.12.2021 •Art No P7100549
User Manual •Instrukcja Obsługi
5.2 Specyfikacja zasilania
5.3 Podłączenie zasilania
Napięcie Zasilania Pobór Mocy Częstotliwość zasilania
100~245V 250W 50/60Hz
5.1 Podłączenie sygnału DMX
z wtyczkami
5. POLACZENIA
1
3
22
ŻEŃSKI
XLR
GROUND
DMX +
DMX -
MĘSKI
XLR
3
1
UWAGA!
wykwalifikowany personel techniczny.
ŻEŃSKI
XLR
1
GROUND
DMX +
DMX -
MALE
XLR
2
3
4
5
1
2
3
45
DMX
Controller DMX 512 DMX 512
6. MENU / KANAŁY DMX
Menu UP Down Enter
Menu:
UP/Down:
Enter:
Addr A001-A512 Kod adresu DMX 512
Master
Powolny ruch
SL 1 Tryb kontrolera
SEnS 0-99
LEd
dISP
X do przodu
rTiL
LED Moving Head 60W Spot ver.12.2021 •Art No P7100549
User Manual •Instrukcja Obsługi
Kanał Funkcja Opis
1X
2
3
0-139
4
5Strobe
6Dimmer
7
8Auto mode
9
Kanał Funkcja Opis
1Pan
2
3Tilt
4
5
0-139
6
7Strobe
8Dimmer
9
10
Auto mode
Auto mode 3
Auto Mode 2
110-134 Auto Mode 1
Auto Mode 0
Sound Mode 3
Sound Mode 2
210-234 Sound Mode 1
Sound Mode 0
11
LED Moving Head 60W Spot ver.12.2021 •Art No P7100549
User Manual •Instrukcja Obsługi
LED Moving Head 60W Spot ver.12.2021 •Art No P7100549
www.flash-butrym.pl
F7100549
Table of contents
Languages:
Other Flash Spotlight manuals
Popular Spotlight manuals by other brands
Ivela
Ivela 1940 manual
SUNTERRA
SUNTERRA 360150 owner's guide
Larson Electronics
Larson Electronics GL-9100H-S Instruction guide
Vector
Vector Ultra SPORT SPOT owner's manual
Lumascape
Lumascape LS411LED Important Instructions for Installation
Strong International
Strong International SUPER TROUPER II instruction manual
Mr. Beams
Mr. Beams NetBright MBN350 installation instructions
Bosch
Bosch CleverMixx Spotlight MFQ25 Series instruction manual
Monacor
Monacor img Stage Line PARL-56PDX/CR instruction manual
iverlux
iverlux PL4K01015 quick start guide
Ignition
Ignition 2bright Pint FC150 IP user manual
Black & Decker
Black & Decker VEC158BD instruction manual
