Flavel Emberglow FEBC00MN User manual

Supplied By www.heating spares.co Tel. [phone]
Emberglow
COAL EFFECT BALANCED FLUE GAS FIRE
Installation and Maintenance Instructions
Hand these instructions to the user
Model No’s FEBC00MN is for use on Natural Gas (G20) at a
supply pressure of 20 mbar in G.B. / I.E.

Supplied By www.heating spares.co Tel. [phone]
CONTENTS
PAGE
Section 1 Information and Requirements
1.0 Appliance Information 3
1.1 Conditions of Installation 4
1.2 Fireplace surround & suitability 4
1.3 Flue Terminal Position 5
1.4 Shelf position 6
1.5 Hearths 6
Section 2 Installation of Fire
2.1 Unpacking the fire 6
2.2 Preparation of the wall 7
2.3 Preparation of the flue hole 8
2.4 Preparation of the flue pipes 9
2.5 Installation of the gas supply 10-11
2.6 Securing of the combustion chamber to the wall 11-12
2.7 Fitting the terminal guard 12
2.8 Removal & refitting of the glass frame 13
Section 3 Assembling Fuel Bed and Commissioning
3.1 Fitting the fuel bed 14
3.2 Lighting the appliance 15-16
3.3 Fitting the fender 17
3.4 Fitting the canopy 17
Section 4 Maintenance
4.1 Removal of the Burner Assembly 18
4.2 Removal of the Control Valve 18-19
4.3 Removal of the Battery Pack 19
4.4 Removal of the Pilot Assembly 19
4.5 Removal of the Touch Control Switch 19-20
The model no. of this appliance is on the rating plate, which is affixed to the
battery pack retaining bracket on the front right hand side of the fire. The product
is manufactured by:-
CFM Europe Ltd, Trentham Lakes, Stoke-on-Trent, Staffordshire, ST4 4TJ
2

Supplied By www.heating spares.co Tel. [phone]
SECTION 1
INFORMATION AND REQUIREMENTS
1.0 APPLIANCE INFORMATION
Main injector : (1 off) Bray Injector Elbow – size 360
Pilot Type : S.I.T.140 Series NG – size 27
Max. Gross Heat Input : 5.25 kW
Min. Gross Heat Input : 2.05 kW
Gas Rate : 0.470 m3/hr (High)
0.190 m3/hr (Low)
Cold Pressure : 20.0+/-1.0 mbar (8.0 +/- 0.4 in w.g.)
Ignition : Integral to gas valve
Electrode Spark Gap : 4.0mm
Weight (Product & Fender) : 33 kg
Weight (Canopy) : 23 kg
3
673mm
445mm
290mm
198mm
716mm
645mm
Fig 1 -
Product
Dimensions

Supplied By www.heating spares.co Tel. [phone]
INSTALLATION REQUIREMENTS
1.1 CONDITIONS OF INSTALLATION
In Great Britain :-
It is the law that all gas appliances are installed only by a CORGI Registered
Installer , in accordance with these installation instructions and the Gas Safety
(Installation and Use) Regulations 1998 as amended. Failure to install appliances
correctly could lead to prosecution. It is in your own interest and that of safety to
comply with the law.
The installation must also be in accordance with all relevant parts of the Local and
National Building Regulations where appropriate, the Building Regulations
(Scotland Consolidation) issued by the Scottish Development Department, and all
applicable requirements of the following British Standard Code of Practice.
1. B.S. 5871 Part 3 Installation of Decorative Fuel Effect Gas Fires
2. B.S. 6891 Installation of Gas Pipework
3. B.S. 5440 Parts 1 & 2 Installation of Flues and V entilation
4. I.S. 813 : 1996 Domestic Gas Installation (Republic of Ireland)
If installing this product into a timber framed building, please consult document
IGE / UP 7, issued by the Institute of Gas Engineers.
In Republic of Ireland :-
No purpose made additional ventilation is normally required for this
appliance, when installed in G.B. When Installing in I.E. please consult
document I.S. 813 : 1996 Domestic Gas Installation, which is issued by the
National Standards Authority of Ireland. If installing in Northern Ireland,
please consult local building regulations. Any purpose made ventilation
must be checked periodically to ensure that it is free from obstruction.
1.2 FIREPLACE / SURROUND SUITABILITY
The fire must only be installed on a hearth it must not be installed directly onto
carpet or other combustible floor materials.
The fire is suitable for fitting to non-combustible fire place surrounds and propri -
etary fire place surrounds with a temperature rating of at least 150
oc.
If a heating appliance is fitted directly against a wall without the use of a fire
surround or fire place all combustible material must be removed from behind
the trim. Soft wall coverings such as blown vinyl, wall paper etc. could be
affected by the rising hot air and scorching and/or discoloration may result.
Due consideration should be made to this when installing or decorating.
4

Supplied By www.heating spares.co Tel. [phone]
1.3 FLUE TERMINAL POSITION
The minimum acceptable dimensions from the flue terminal to obstructions
and ventilation openings are shown below and listed in the table
It is important that the position of the flue allows the free passage of air
across it at all times. The minimum acceptable space from the flue terminal
to obstructions and ventilation openings are specified below (Fig. 2)
Fig. 2
DIMENSION TERMINAL POSITION MINIMUM DIMENSION
ADirectly below an opening, air brick, 300mm (12in)
opening window
BAbove an opening, air brick, 300mm (12in)
opening window
CHorizontally to an opening, air brick,
opening window etc.
DBelow gutters, soil pipes or drain pipes 300mm (12in)
EBelow eaves 300mm (12in)
FBelow balconies or car port roof 600mm (12in)
GFrom a vertical drain pipe or soil pipe 300mm (12in)
HFrom an internal or external corner 600mm (24in)
IAbove ground roof or balcony level 300mm (12in)
JFrom a surface facing the terminal 600mm (24in)
KFrom a terminal facing the terminal 600mm (24in)
LFrom an opening in the car port 1200m (48in)
M Vertically from a terminal on the same wall 1500mm(59in)
NHorizontally from a terminal on the 300mm (12in)
same Wall
ONOT APPLICABLE N/A
PNOT APPLICABLE N/A
QNOT APPLICABLE N/A
5