Flexa 4838034 User manual

6 Drawer Under Bed Unit - White
Dimensions
Length - 187cm
Depth - 49cm
Height - 37cm
Weight - 31kg
Issue 2 - 19/10/15
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline:
0045 7668 8055 or e-mail: order@flexa.dk
Assembly Instructions - Please keep for future reference 4838034

1
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close
to its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could
damage the unit. Only use hand
screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Care and maintenance
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.

2
Components - Parts
Please check you have all the parts listed below
Back panel x3
(60.9x35.7x0.3cm)
9
Drawer front x6
(59.8x17.3x1.5cm)
No. 15-01505983-20 No. 4308-030609
Side panel x4
(36.3x48.5x1.5cm)
1
No. 15-01503631-20
Drawer back x6
(56.8x14.6x1.3cm)
5
No. 12-01305683
Drawer side right x6
(43.0x14.6x1.3cm)
2
No. 12-01304301
Plinth x6
(60.2x6.5x1.5cm)
Plinth x6 White
(60.2x6.5x1.5cm)
6
7
No. 12-01506021
No. 12-01506021-20
Drawer base x6
(58.0x42.5x0.3cm)
No. 4309-030580
If you have damaged or missing components,
call the Customer Helpline: 0045 7668 8055
3
8
Drawer side left x6
(43.0x14.6x1.3cm)
No. 12-01304302
4

Please check you have all the fittings listed below
ø7x34mm Minifix bolt x32
Tools required
A
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
ø15x9.5mm Minifix cam x48
B
E
ø7/M4x34mm Minifix bolt x16
C
D
Components - Fittings
3
FNo. 4001-022-20
G
ø9.5/M4x9mm Machine screw x12 430x17x10mm Drawer runner x12 ø40x30mm Knob x6
H
3.5x40mm Chipboard screw x48
No. 3901-35040
Phillips
screwdriver
(medium)
Small
hammer
Ruler/tape
measure
Eye protection
(when using a
hammer or glue)
5x30mm Dowel x24
No. 3930-05030
ø5x15mm Sleeve connector x20
J
KNo. 4022-006
1.2x20mm Nail square x50
LNo. 3907-58011
ø5.8x11mm Euro screw x12
P
ø7,3/M4x8mm Machine screw x24
N
i
4.0x40mm Chipboard screw x6
No. 3903-40040
8x30mm Dowel x24
4.0x25mm Chipboard screw x4
No. 3930-08030
No. 3901-40025
M
ONo. 4008-021
20x20x16x2 Angle x2
No. 3920-04008
No. 4020-006
No. 3924-04015
No. 3933-15010
No. 4020-005
No. 4010-006
No. 3912-04009

44
Assembly Instructions
Step 1
Attach the dowels Hto
the plinths 6and 7.
It may be necessary
to tap the dowels in
very gently with a small
hammer.
Repeat for all twelve
plinths.
Attach minifix bolts Cto
the sleeve connectors
Dand gently tap the
connectors Dinto the
holes in side panels 1
(2. and 3.). Unscrew the
minifix bolts Cfrom the
connectors D.
Attach the drawer
runners Eto side panels
1(2. and 3.) using
screws P.
Important! Do not
tighten the screws P
until all 3 screws are
inserted into the holes.
Be aware of the forward
end!
Step 2
H
H
67x12
H
1
1
1
1
1
P
P
P
P
P
P
P
P
P
P
P
P
P
E
E
E E
E
E
P
C
C
C
C
C
C
C
C
C
C
C
C
D
D
D
D
D
D
D
D
D
D
D
D
C
C
D
Front edge
Front edge Front edge Front edge
(2.)
(2.)
(3.)
(3.)
Step 3
Middle side Middle side
Middle sideMiddle side
Front edge

Assembly Instructions
Step 4
Attach minifix bolts Cto
the sleeve connectors
Dand gently tap the
connectors Dinto the
holes in side panels 1
(2. and 3.).
Flip the side panel over
and attach the drawer
runners Eto the other
side of side panels 1(2.
and 3.) with screws P.
Important! Do not
tighten the screws P
until all 3 screws are
inserted into the holes.
Be aware of the forward
end!
5
Step 5
C
C
C
C C
C C
D
D
D
D D
D D
D
D
Front edge
Front edge Front edge
Front edge
Middle side Middle side
Middle sideMiddle side
1
1
(3.)
(2.)
1
1
(2.)
(3.)
Front edge
P
PP
P
P
P
P
P
P
P
P
P
P
P
E
E E
E E
E P
P

Please note! The minifix
bolts Cshould only
be tightened with your
fingers, not tightened into
the wood/panels using a
screwdriver.
Attach minifix bolts C
to the other side of side
panels 1(2. and 3.).
Please note! Make sure
the 2 small holes in the
panels are facing down
against the floor.
Assemble the middle
section by placing the
plinths 6and 7
between the side panels
1(2. and 3.).
Please note! Make sure
the 2 small holes in the
panels are facing down
against the floor.
Attach drawer runners E
to the side panels 1(1.
and 4.) using screws L.
Important! Do not
tighten the screws L
until all 3 screws are
inserted into the holes.
Assembly Instructions
Step 6
Step 7
Step 8
6
C
C
C
C C
C C
C C
Front edge Front edge
Front edge Front edge
Middle sideMiddle side
Left side Right side
1
1
1
1
6
6
7
7
(4.)
(2.)
(2.)
(3.)
1
1
(1.)
(3.)
Front edge
E
L
L L
L L
L L
L L
L L
L
L
E
E E
E E
L
! !
!
!

Please note! Make sure
the 2 small holes in the
panels are facing down
against the floor.
Attach the minifix bolts
Ato side panels 1(1.
and 4.)
Assemble the left and
right section by placing
plinths 6and 7
between the side panels
1(1. and 2. and 3. and
4.)
Insert minifix cams B
into the holes in the
plinths 6and 7and
tighten the cams using a
screwdriver. Slide back
panels 9into grooves in
side panels 1.
Assembly Instructions
Step 9
Step 11
7
Step 10
A
A
A A
B
B
B
B
B
B
B
B
B
B
B
B
B
A
A A
Front edge Front edge
Left side Right side
1(4.)
1
1
1
1
1
1
1
1
1
(1.)
(1.)
(2.)
(3.)
(4.)
6
6
6
6
6
7
7
7
7
7
7
7
7
7
7
6
6
6
6
6
9
9
9
!
!

Please note! The nails
should be positioned at
least 5 cm from the side
panels. If not, the nail
may hit the minifix cam in
the plinth.
Attach the back panels
9to the plinths 6and
7using nails K. Make
sure that there is no gap
between the plinths and
the back panels.
Insert minifix bolts Ainto
holes in the drawer front
8. Attach knob Fto the
drawer front using screw
M.
Repeat for all six
drawer fronts.
Insert dowels Ninto
holes in drawer sides 3
and 4.
Repeat for all twelve
drawer sides.
Assembly Instructions
Step 12
Step 13
Step 14
8
5cm 5cm
5cm 5cm
5cm 5cm
K
K
K
F
F
N
N
A
A
A
A
A
M
M
K
K
K
K
9
9
9
7
7
8
3 4
7
/

Attach the drawers sides
3and 4to the drawer
front 8using minifix
cams B.
Repeat for all six
drawers.
Push the drawer base 2
carefully into the drawer.
Attach the drawer back
5to the drawer sides
3and 4with the
screws J.
Repeat for all six
drawers.
Assembly Instructions
Step 15
Step 16
9
B
B
J
J
J
B
3
4
8
2
5
3
4

Attach the drawer to the
drawer runners Ewith
the machine screws G
inside to the drawer sides
3and 4.
Repeat for all six
drawers.
Position the bed where
it will be placed in the
future, before attaching
the 6 drawer underbed
unit to the bed. Bed and
6 drawer unit can’t be
moved together after the
unit has been attached
to the bed with the 2
brackets.
Assembly Instructions
Step 17
Step 18
10
4
G
G

Step 19
Assembly Instructions
If you need help or have damaged or missing parts, call the Customer Helpline: 0045 7668 8055
E-mail: order@flexa.dk
Ref.no. 44-01529-20 B Stand: 191015 Page 12 (81-07709-20)
The underbed unit should
be flush with the bedside
rail.
Secure the unit in place
with angles Oand
chipboard screws i.
Assembly is complete.
11
O
i
i
Step 20
Unit flush with the
bedside rail.