Flexa Cabin bed 1478538 User manual

Cabin bed - White
Dimensions
Length - 195cm
Depth - 96cm
Height - 71cm
Weight - 20kg
Issue 1 - 05/10/15
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline:
0045 7668 8055 or e-mail: order@flexa.dk
Assembly Instructions - Please keep for future reference 1478538

1
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
80-10104-20 debnibaC
IMPORTANT! KEEP FOR FUTURE REFERENCE
PLEASE DISPOSE OF PACKAGING MATERIAL.
PLASTIC BAGS CAN BE DANGEROUS TO YOUNG CHILDREN
WARNING! Not suitable for children under 4 years.
WARNING! Do not place this child’s bed near heat sources, windows and other furniture.
WARNING! Do not use this child’s bed if any of the parts are broken, torn or missing.
WARNING! Once assembled, this bed must not be disassembled. Screws must not be removed once inserted.
This child’s bed is to be used with a 1900mm x 900mm ma ress.
Suitable for children over 4 years to adults.
All assembly Įxings should be checked periodically and re- ghtened where necessary.
Children are likely to play, bounce, jump and climb on beds, therefore the child’s bed should not
be placed too close to other furniture or windows, blind cords, curtain pulls or other strings or cords, and should be
placed either ght to any wall or have a gap of 300mm between the wall and the side of the bed.
Any addi onal or replacement parts should only be obtained from the manufacturer or distributor.
This product complies to standard BS8509: 2008+A1:2011
CARE AND MAINTENANCE
To clean use a damp cloth, avoiding the use of strong detergents or abrasives.

Safety and Care Advice
Important – Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close
to its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could
damage the unit. Only use hand
screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Care and maintenance
2

T&G panel x2
(58.5x8.1x0.8cm)
7Bedside x2
(186.7x8.9x2.0cm)
8
Endrail x2
(87.7x6.5x2.0cm)
3
Components - Parts
Please check you have all the parts listed below
Leg x4 (71.7x4.3x4.3cm)
1
Slat x14 (89.7x6.5x1.47cm)
4
No. 12-02008772-20
Endrail curved x2
(87.7x9.2x2.0cm)
2
No. 12-02008771-20
T&G panel x2
(58.5x8.7x0.8cm)
5
No. 12-00805852-20
T&G panel x16
(58.5x9.4x0.8cm)
6
No. 12-00805851-20
No. 12-00805853-20 No. 1305-18673-20
If you have damaged or missing components,
call the Customer Helpline:
0045 7668 8055
3
No. 12-04307172-20
No. 12-01508971

Components - Fittings
Please check you have all the fittings listed below
M6x90mm Connecting bolt x4
Tools required
A
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
M6 ø10x14mm Barrel nut x4
B
E
4,0x30mm Chipboard screw x28
C
10x45mm Dowel x8
D
Phillips
screwdriver
(medium)
Small
hammer
Allen key
4mm incl.
Flatblade
screwdriver
(medium)
6,3x90mm Assembly screw x16
Ruler/tape
measure
Eye protection
(when using a
hammer or glue)
4
No. 3901-40030
No. 3930-10045
No. 3922-06014
No. 3913-06090
No. 4033-004
No. 3909-63090

Important note:
A variation of the width of the panels of ±2-3% has to be expected as wood is
a live material, i.e. variation of 2-3 cm per 1 meter.
Leaving some space at the panels, tongue & groove, should be distributed
regularly along the bed end.
If there is too little space for the panels, these should be acclimatized for 2-5
days in order to adapt to the humidity of the room.
The reason for this problem might be that the wood has absorbed a little
moisture during transportation/stocking.
Attach the dowels Dto
bedsides 8.
It may be necessary
to tap the dowels in
very gently with a small
hammer.
Attach endrails 2and
3to leg 1with screws
Eusing the allen key.
Repeat same procedure
for second headboard
Slide T&G panel 7
between endrails 2and
3.
Followed by 8 T&G panel
6and finish with 1 T&G
panel 5.
Attach leg 1to endrails
2and 3with screws
Eusing the allen key.
Repeat same procedure
for second headboard
Assembly Instructions
Step 1
7
8x2
2
1
5
3
1
6
6
6
6
6
6
6
6
2
3
1
7666 6 5
Step 2
DD
D
E
E
E
E
E
E
Step 3
5
410 307
UP
DOWN

Attach bedsides 8to
the legs 1by pushing
the barrel nuts Binto
the small holes in the
bedsides 8. Push
connecting bolts A
through the legs 1to
meet the barrel nuts B.
Then fasten with the
allen key.
Repeat same procedure
as described in “Step
4”
Step 5
Assembly Instructions
Step 4
8
8
A
A
A
B
B
B
B
8
1
1
1
1
A
B
8
8
8
B
A
A
B
B
6

Assembly Instructions
If you need help or have damaged or missing parts, call the Customer Helpline: 0045 7668 8055
E-mail: order@flexa.dk
Ref.no. 44-01139-20 D Stand: 051015 Page 8 (80-10104-20)
Place one slat 4in the
centre of the bed. Follow
the measurement .
Place two slats 4in the
ends of the bed. Follow
the measurement .
Push the bedsides 8
together whilst attaching
middle slat 4to the
bed with two chipboard
screws C.
Position the remaining
eleven slats 4in the
bed with a distance of 73
mm between each.
Fasten each slat with two
screws C
Assembly is complete.
Step 6
4
4
C
C
C
C
C
C
C
C
73 mm
15 mm
843 mm
PUSH
PUSH
8
8
44
4444 4 4 4 4 4 4
Step 7
7