Floe 511-01354-00 User manual

1
FLOE SOLAR PANELS
KIT -12V KIT, SOLAR PANEL 12V
-24V KIT, SOLAR PANEL 24V
ASSEMBLY INSTRUCTIONS
P/N: 511-01354-00, 511-01356-00
INSTRUCTION P/N: 611
-
01354
-
00
RELEASED 10/14/19
© Manufactured by:
Floe International Inc.
48473 State Hwy. 65
McGregor, MN 55760
www.floeintl.com
TOOLS REQUIRED
-3/8” WRENCH
-9/16” SOCKET/WRENCH (2)
-3/4” SOCKET/WRENCH
-PHILLIPS HEAD SCREWDRIVER
-TORQUE WRENCH
-ELECTRICAL TAPE
NOTE:
EITHER 511-01357-00,
511-01358-00, OR 511-
01359-00 IS REQUIRED
FOR MOUNTING.
BOTH ARE SOLD
SEPARATELY.

2
511-01354-00 Kit, Solar Panel 24V
NUMBER PART NUMBER DESCRIPTION QTY.
1 001-70105-00 HHCS, 3/8-16 x 1" 18-8 ss 4
2 001-70207-00 HHCS, 1/2-13 x 1 1/4" 18-8 ss 2
3 001-71009-00 Flat Washer, #10 Small O.D. ss 8
4 001-71017-00 Flat Washer, 3/8" SAE ss 18-8 4
5 001-71021-00 Flat Washer, 1/2" 18-8 ss 2
6 001-72517-00 PHMS, #10-32 x 5/8" Phillips 18-8 ss 8
7 001-76072-00 NUT, NYLOCK 1/2-13 ALUM 2
8 001-76073-00 Nut, Nylock 10-32 Alum 8
9 011-00902-00 Kit, Solar Panel w/ Contr. amp; Harn. 2
10 211-80030-00 Mast, Solar Panel 1
11 111-00467-00 Mount, Upper Solar Panel, 24V 1
511-01356-00 Kit, Solar Panel 12V
NUMBER PART NUMBER DESCRIPTION QTY.
1 001-70105-00 HHCS, 3/8-16 x 1" 18-8 ss 4
2 001-70207-00 HHCS, 1/2-13 x 1 1/4" 18-8 ss 2
3 001-71009-00 Flat Washer, #10 Small O.D. ss 8
4 001-71017-00 Flat Washer, 3/8" SAE ss 18-8 4
5 001-71021-00 Flat Washer, 1/2" 18-8 ss 2
6 001-72517-00 PHMS, #10-32 x 5/8" Phillips 18-8 ss 8
7 001-76072-00 NUT, NYLOCK 1/2-13 ALUM 2
8 001-76073-00 Nut, Nylock 10-32 Alum 8
9 011-00902-00 Kit, Solar Panel w/ Contr. amp; Harn. 2
10 211-80030-00 Mast, Solar Panel 1
11 111-00468-00 Mount, Upper Solar Panel, 12V 1
BILL OF MATERIALS
511-01356-00 (12V)
BILL OF MATERIALS
511-01354-00 (24V)

3
EXPLODED VIEW
511-01354-00 (24V)
EXPLODED VIEW
511-01356-00 (12V)

4
INSTALLATION
STEP 1
-ATTACHING PANEL(S)
ATTACH THE PANEL(S) TO THE UPPER MOUNT WITH PHMS #10-32 x 5/8” SCREWS,
#10 WASHERS, AND 10-32 NYLOCK NUTS (4 FOR 12V SYSTEMS, 8 FOR 24V
SYSTEMS). TIGHTEN UNTIL BOLT HAS NO FREE PLAY. DISCONNECT HARNESS(ES)
(LONGER JACKETED WIRES) FROM SOLAR PANEL CONTROLLERS, THEN PUSH
PANEL WIRE(S) (SHORTER WIRES) THROUGH THE PLUG(S) IN THE UPPER MOUNT.
STEP 2
-WIRE FEEDING
TAKE THE DISCONNECTED HARNESS(ES) AND FEED THEM THROUGH THE MAST.
RE-CONNECT THE HARNESS TO THE PANEL CONNECTOR.
INSTALL THE SOLAR PANEL
CONTROLLERS AT OPPOSITE
CORNERS SO THAT THE WIRES ON
EACH CONTROLLER REACH THE
GROMMET ON THE SIDE NEAREST
TO THE CONTROLLER

5
WRAP ELECTRICAL TAPE AROUND BOTH CONNECTORS TO EACH SOLAR PANEL.
TAPE SHOULD WRAP PAST PLUGS APPROXIMATELY ONE INCH.
STEP 3
-ATTACH MAST TO UPPER MOUNT
ATTACH THE MAST TO THE UPPER MOUNT ASSEMBLY WITH (2) 3/8-16 x 1” BOLTS
AND (2) 3/8” WASHERS BY PLACING THEM THROUGH THE UPPER MOUNT HOLES
AND INTO THE RIVET NUTS IN THE MAST. TORQUE TO 10 FT-LBS.

6
STEP 4
-ATTACH LOWER MOUNT TO CANOPY LEG
NOTE: THE BRACKET MAY BE ON THE BALL SCREW SIDE OR THE V-BRACE
SIDE OF THE LIFT. HOWEVER, THE BRACKET MUST BE ON THE TILTING
CORNER POST IN MAXIS APPLICATIONS.
NOTE: LOWER BRACKET SOLD IN SEPARATE KIT.
ATTACH THE ASSEMBLY TO THE CANOPY LEG BY PLACING (2) 1/2-13 x 1 1/4”
BOLTS AND (2) 1/2” WASHERS INTO THE LOWER MOUNT AND SLIDING THEM
INTO THE CANOPY LEG. PLACE (2) 1/2-13 NYLOCK NUTS AND TORQUE TO 60
FT-LBS.
OR

7
STEP 5
-ATTACH MAST TO LOWER MOUNT
FEED WIRE HARNESSES THROUGH THE LOWER MOUNT. ATTACH THE MAST TO
THE LOWER MOUNTING BRACKET WITH (2) 3/8-16 x 1” BOLTS AND (2) 3/8”
WASHERS BY PLACING THEM THROUGH THE LOWER MOUNT HOLES AND INTO
THE RIVET NUTS IN THE MAST. TORQUE TO 10 FT-LBS.
STEP 6
-WIRE ROUTING
FOLLOW THE BELOW DIAGRAMS FOR WIRE ROUTING. KEEP WIRING AWAY FROM
ALL MOVING PARTS.

8
-BATTERY CONNECTIONS
CONNECT THE RED LEAD TO THE POSITIVE TERMINAL OF THE BATTERY AND THE
BLACK LEAD TO THE NEGATIVE TERMINAL OF THE BATTERY. REPEAT FOR THE
SECOND BATTERY (IF APPLICABLE).
NOTE: ONLY ONE SOLAR PANEL IS CONNECTED TO AN INDIVIDUAL BATTERY.
KEEP WIRING AWAY FROM ALL MOVING PARTS.
BLACK LEAD TO NEGATIVE POST
RED
LEAD TO POSITIVE POST