Florence 1040401 User manual

Assembly Instructions - Please keep for future reference
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, please contact Your retailer
White 1040401
Black 1040420
Soft grey 1040452
Issue 1 - 09-11-2016
Dressing Table
Dimensions
Width
Depth
Height
:
:
:
350835
101.2 cm
40.0 cm
76.0 cm

!Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Care and maintenance
1
• Check you have all the
components and tools listed on
pages 2 and 3.
•Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
•Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
•Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
•We do not recommend the use
of power drill/drivers for
inserting screws, as this could
damage the unit. Only use hand
screwdrivers.
•Dispose of all packaging
carefully and responsibly.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
•This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page
with these instructions for
future reference.

Components - Panels
Please check you have all the panels listed below
2
350835-03
2
(15 cm x 30,6 cm)
Side, left
9
(30 cm x 9,8 cm)
Drawer side, right/left
2
x
1
(101,2 cm x 40 cm)
Top
3
(15 cm x 30,6 cm)
Side, right
7
(88,2 cm x 6 cm)
Front rail
6
(88,2 cm x 15 cm)
Back rail
6
x
8
(29,0 cm x 12,5 cm)
Drawerfront
10
(22,8 cm x 9,8 cm)
Drawer back
11
(23,8 cm x 29,7 cm)
Drawer bottom
3
x
3
x
3
x
4
(74,5 cm x 5,0 cm)
Leg, left
5
(74,5 cm x 5,0 cm)
Leg, right
2
x
2
x
13
Safety label
12
(11,9 cm x 29,1 cm)
Divider

Components - Fittings
Please check you have all the panels listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more ttings
may be supplied than are required.
3350835-04
26 ø8 x 40mm Wooden dowel x
Aa Ab
ø6 x 30mm Wooden dowel x 12
Cp
ø5 x 11, cc34mm Bolt x 28
Ca
ø15 x 10.5mm Cam x
28
Kb
ø5.8 x 8mm Screw x
12
17060 16040 90 15013070 120100 14011050 803020100
Ruler - Use this ruler to help correctly identify the screws
Tools required
Flatblade screwdriver
(Medium)
Hammer Phillips screwdriver
(Medium & large)
Back fitting w. ø3.5 x 15mm Screw x
Fi
6
ø3 x 35mm Screw x
Bp
12
Ge
3 ø27 x 24mm Metal Knob x M4 x 20mm Screw x
Hd
3 Wall strap and instruction x 1
Fh
ø18 x 9mm Spacer x
Nu
6
Kf
6
ø5.8 x 19mm Screw x
ø5 x 38mm Screw x
Dj
4
3
CL
300mm Drawer runner, left, side x
3
CR
300mm Drawer runner, right, side x
3
DL
300mm Drawer runner, left x 3
DR
300mm Drawer runner, right x
ø3 x 12mm Screw x
Bo
12

Assembly Instructions
Place the legs 4and
5onto the sides 2
and 3.
Push cams
Ca
into the
holes indicated on the
sides 2and 3.
Arrows pointing towards
the legs 4/5.
Turn the cams
Ca
to the
right to x the legs 4
and 5.
Step 1.3
Assembly of the table.
Step 1
Knock the dowels
Aa
into the holes indicated
on the sides
2
and
3
using a small hammer.
Step 1.1
Screw the bolts
Cp
into
the holes indicated on the
legs
4
and
5
.
Step 1.2
4
350835-05
16 ø8 x 40mm Wooden dowel x
Aa
3
5
4
2
4
2
5
1
3
5
Cp
ø5 x 11, cc34mm Bolt x 8
Ca
ø15 x 10.5mm Cam x
8
3
2
6
7
4
5
4
5
4
Ca
Ca
Ca
Ca
Cp
Aa
Aa Aa
Aa
Aa
Aa
Aa
2
x
2
x
12 12
Cp

Assembly Instructions
Place the spacers
Nu
as shown, and x the
upper drawer runners
CL
and
CR
to the sides
2and 3using screws
Kf
through the holes
indicated.
See details.
Step 1.5
Screw the bolts
Cp
into
the holes indicated on the
sides
2
and
3
.
Step 1.4
350835-06
5
2
ø18 x 9mm Spacer x
Nu
6
Kf
6
ø5.8 x 19mm Screw x
3
2
Cp
ø5 x 11, cc34mm Bolt x 6
Cp
Cp
Cp
Cp
3
1
CL
300mm Drawer runner, left, side x
1
CR
300mm Drawer runner, right, side x
Kf
Kf
Nu
CL
CR
Nu
Nu
Nu
Kf
Kf
CL
CR
Kf
Kf
Nu
Nu
Cp
Cp

Assembly Instructions
Knock the dowels
Aa
into
the holes indicated on
the dividers
12
using a
small hammer.
Step 1.7
Knock the dowels
Aa
into
the holes indicated on
the back rail
6
and the
front rail
7
using a small
hammer.
Step 1.6
Fix the drawer runners
CR
to the left hand side
of the divider 12 using
screws
Kb
through the
holes indicated.
Turn around the divider
12 and x the drawer
runner
CL
using screws
Kb
through the holes
indicated.
See details.
Step 1.8
6
350835-07
Kb
ø5.8 x 8mm Screw x
12
Kb
Kb
Aa
Aa
6
7
Aa
Aa
2
x
Aa
Aa
6 ø8 x 40mm Wooden dowel x
Aa
4
ø8 x 40mm Wooden dowel x
Aa
2
CL
300mm Drawer runner, left, side x
2
CR
300mm Drawer runner, right, side x
12
12
Kb
Kb
CR
CL Kb
Kb
CR
CL
12

Assembly Instructions
Place the sides 2and
3onto the back rail 6
and the front rail
7.
Push cams
Ca
into the
holes indicated on the
back rail 6and the front
rail
7.
Arrows pointing towards
the sides 2/3.
Turn the cams
Ca
to the
right to x the sides 2
and 3.
Step 1.11
Screw the bolts
Cp
into
the holes indicated on the
top
1
.
Step 1.9
Place the dividers 12
onto the top
1.
Push cams
Ca
into the
holes indicated on the
dividers 12 , arrows
pointing towards
the top 1.
Turn the cams
Ca
to the
right to x the
dividers 12 .
Step 1.10
350835-08
7
Ca
ø15 x 10.5mm Cam x
6
Ca
Ca
Ca
Ca
Ca
3
7
6
2
Cp Cp
1
Cp
Cp
Ca
ø15 x 10.5mm Cam x
4
Cp
ø5 x 11, cc34mm Bolt x 8
1
Ca
Ca
Ca
Ca
12
12
Cp Cp
Cp Cp

Assembly Instructions
Step 1.14
!
Important!
The dressing table
is heavy.
Lift with care.
Its recommended that the
dressing table is xed to the
wall.
Use the ttings
Fh
. Follow
the instructions on the
following pages.
Place the sides 2and
3onto the top 1.
Push cams
Ca
into the
holes indicated on the
sides 2and 3.
Arrows pointing towards
the top 1.
Turn the cams
Ca
to the
right to x the top 1.
Step 1.12
Fix the back rail 6and
the front rail 7to the
dividers 12 as shown,
using screws
Dj
.
Step 1.13
350835-08
7
Ca
ø15 x 10.5mm Cam x
6
Ca
Ca
Ca
Ca
Ca
3
7
6
2
Cp Cp
1
Cp
Cp
Ca
ø15 x 10.5mm Cam x
4
Cp
ø5 x 11, cc34mm Bolt x 8
1
Ca
Ca
Ca
Ca
12
12
Cp Cp
Cp Cp
8
350835-10
Wall strap and instruction x 1
Fh
Ca
ø15 x 10.5mm Cam x
4
1
3
2
Ca
Ca
Ca
ø5 x 38mm Screw x
Dj
4
6
7
Dj
Dj
Dj
Dj

Assembly Instructions
Place the dressing table
up against the wall.
Draw a line as shown
using a pencil.
Step 1.15
Fix the strap to the wall
140mm below the line as
shown.
Note!
See next page for
information on how to x
the strap to the wall. The
screw and plug needed is
NOT included.
Step 1.16
Push dressing table up
against the wall.
Step 1.17
Fix the strap to the back
rail 6using the screw
and washer provided.
See detail.
Step 1.18
350835-10
9
140 mm
6
6
6
6

A Guide to
Wall Mounting & Fixings
350835-10
9
140 mm
6
6
6
6
No.3 "Shield Anchor" Wall Plug
Heavy Loads
For use with heavier loads such as TV
& HiFi Speakers and Satellite Dishes etc.
No.4 "Cavity Fixing" Wall Plug
For use with plaster board partitions or
hollow wooden doors.
No.5 "Cavity Fixing - Heavy Duty"
Wall Plug
For use when fitting or supporting heavy
loads such as shelving, wall cabinets,
coat racks.
IMPORTANT:
When drilling into walls always check that there are no
hidden wires or pipes etc. Make sure that the screws and
wall plugs being used are suitable for supporting your unit.
Consult a qualified tradesperson if you are unsure.
HINTS:
1) General Rule Always use a larger screw and wall plug if you are not sure.
2) Ensure you use the recommended drill bit to match the wall plug and hole size.
3) Ensure you drill the hole horizontally, do not force the drill or enlarge the hole.
4) Take extra care when drilling high walls, ceilings and ceramic tiles. Ensure the plug is fitting below the ceramic
tile to avoid splitting or cracking.
5) Ensure wall plugs are well fitted and are a tight fit in the drilled hole.
Types Of Walls
You can use one of the following types
of wall plug if your walls are made of
brick, breeze block, concrete, stone,
wood or plaster board.
No.1 "Standard" Wall Plug
General Wall Materials
These come in various sizes and are made
from plastic or sometimes wood fiber.
No.2 "General Purpose" Wall Plug
Aerated / Breeze Block
Generally aerated blocks should not be
used to support heavy loads, use a
specialist fitting in this case.
For light loads, a General Purpose Plug
can be used.
No.6 "Hammer Fixing" Wall Plug
For use with walls stuck with plaster
board.The hammer fixing allows it to
be fixed to the wall rather than the plaster
board.Always check the fixing is secure
to the retaining wall.
CARE & MAINTENANCE
SAFETY
Always check the fitting and
location to ensure your safety in
and around the home.
FITTING
From time to time check the fitting
to ensure the wall plugs or screws
do not become loose.

Assembly Instructions
Step 2.5
Push the drawer front
8
onto the drawer sides
9
.
Place cams
Ca
into the
holes indicated. Arrow
pointing towards the front.
Turn the cams
Ca
to the
right to x the front.
Knock the dowels
Ab
into the holes indicated
on the drawer sides 9
using a smal hammer.
Step 2.2
Slide the drawer bottom
11 into the drawer
sides 9.
Step 2.3
Fix the drawer sides 9
to the drawer back 10 as
shown, using screws
Bp
.
Step 2.1
Assembly of the drawers.
Step 2
Step 2.4
Screw the bolts
Cp
into
the holes indicated on
the drawer front 8.
350835-12
11
3
x
3
x
Bp
Bp
ø3 x 35mm Screw x
Bp
12
10
9
9
11
10
99
Ab
ø6 x 30mm Wooden dowel x 12
3
x
3
x
9
9
11
9
9
3
x
8
Cp
ø5 x 11, cc34mm Bolt x 6
Cp
Ab
Ab
8
3
x
9
9
Ca
Ca
8
Ca
ø15 x 10.5mm Cam x
6
Cp

Assembly Instructions
Step 2.6
!
Important!
Make sure the
angle between
the drawer front
8
and
the drawer sides
9
is 90°
before the drawer bottom
11
is xed using
Fi
as
shown.
To adjust the angle between
the sides and the front push
the tting
Fi
sidewards.
Fix the drawer runners
DL
and
DR
to the drawer sides
9
using screws
Bo
into the
holes indicated.
Step 2.7
Fix the metal knobs
Ge
to the drawer front 8
using screws
Hd
.
Place the drawers on the
drawer runners as shown.
It is necessary to lower
the front end of the
drawer when inserting it.
Step 2.8
90°
12
350835-13
Fi
Fi
Fi
Back fitting w. ø3.5 x 15mm Screw x
Fi
6
3
x
8
Ge
Hd
Fi
Fi
Ge
3 ø27 x 24mm Metal Knob x M4 x 20mm Screw x
Hd
3
3
x
3
DR
300mm Drawer runner, right x3
DL
300mm Drawer runner, left x
ø3 x 12mm Screw x
Bo
12
Bo
"A"
"B"
Bo
Bo
DR
Bo DL
DL
8
9
9
350835-12
11
3
x
3
x
Bp
Bp
ø3 x 35mm Screw x
Bp
12
10
9
9
11
10
99
Ab
ø6 x 30mm Wooden dowel x 12
3
x
3
x
9
9
11
9
9
3
x
8
Cp
ø5 x 11, cc34mm Bolt x 6
Cp
Ab
Ab
8
3
x
9
9
Ca
Ca
8
Ca
ø15 x 10.5mm Cam x
6
Cp

Assembly Instructions
Step 2.9
Remove the paper on the
back of the Warning label
13 and place it inside the
middle drawer as shown.
350835-14
13
Permanent safety label. Please do not remove.
WARNING!
IN ORDER TO PREVENT OVERTURNING
THIS PRODUCT MUST BE USED WITH
THE WALL ATTACHMENT DEVICE
PROVIDED
Serious or fatal crushing injuries can occur from
furniture tipping over. To help prevent topple over:
• Use the wall attachment device provided
• Never allow children to climb or hang on
drawers, doors or shelves
• Place heaviest items in the lower drawers
or shelves
• Unless specifically designed to
accommodate, do not set TV's or other
heavy objects on top of this product
• Never open more than one drawer at a
time
An attachment device is provided with your product,
however you will need to source suitable fixings for your
wall type. If in doubt, please consult a qualified
tradesperson
Always ensure the wall to be drilled is free from hidden
electrical wires, water and gas pipes.
13