Flymo Pac a Shredder User manual

®
IMPORTANT INFORMATION
Read before use
& retain for future reference
Pac a Shredder
34 kg
Original Instructions

Carton Contents
IMPORTANT !
Please check the contents of the carton are correct BEFORE assembling your new Flymo product.
IF ANY PARTS ARE MISSING CONTACT:-
Husqvarna UK Ltd. Customer Service Department direct
Telephone : [phone] UK1800 882 350 ROI Fax : [phone]
Safety
If not used properly this product can be dangerous! This product can cause serious injury to the
operator and others, the warnings and safety instructions must be followed to ensure reasonable
safety and efficiency in using this product. The operator is responsible for following the warning
and safety instructions in this manual and on the product. Never use the product unless the col-
lection box or guards provided by the manufacturer are in the correct position.
Explanation of Symbols on your Product
Warning
Read the user instructions carefully to
make sure you understand all the controls
and what they do.
Keep bystanders away. Do not shred
whilst people especially children or pets
are in the area
Switch off! Remove plug from mains be-
fore adjusting, cleaning or if cable is en-
tangled or damaged. Keep the cable
away from moving parts.
Danger rotating blades. Keep hands out
of openings when machine is running.
Cutting blade continues to rotate after the
machine is switched off. Wait until all ma-
chine components have completely
stopped before touching them.
Do not use in the rain or leave the prod-
uct outdoors while raining
Wear eye protection
Wear Gloves
electric cable
with moulded
on plug and
cable clip
instruction
manual
support foot and bolt
collection
box
cable hook
nut
washer
washer
washer
hub cap
retaining clip
wheel
axle
wheel
hub cap
push stick
retaining clip
washer
cable hook
hexagon drive tool
spanner
support foot and bolt
nut

General
1. This product is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have been
given supervision or instruction concerning the use of the
product by a person responsible for their safety. Children
should be supervised to ensure that they do not play with the
product.Local regulations may restrict the age of the operator.
2. Never allow children or people unfamiliar with the instruc-
tions to use the machine.
3. Stop using the machine while people. especially children,
or pets are nearby.
4. Only use the product in the manner and for the func-
tions described in these instructions.
5. Never operate the product when you are tired, ill or under
the influence of alcohol, drugs or medicine.
6. The operator or user is responsible for accidents or haz-
ards occurring to other people or their property.
Electrical
1. We recommend the use of a Residual Current Circuit Device
(R.C.D.) with a tripping current of not more than 30mA. Even
with a R.C.D. installed 100% safety cannot be guaranteed
and safe working practice must be followed at all times.
Check your R.C.D. every time you use it.
2. Before use, examine the cable for signs of damage or ageing.
If the cable is found to be defective, take the product to
an Authorised Service Centre and have the cable replaced.
3. Do not use the product if the electric cables are damaged or worn
4. Immediately disconnect from the mains electricity supply if
the cable is cut, or the insulation is damaged. Do not
touch the electric cable until the electrical supply has been
disconnected. Do not repair a cut or damaged cable. Re-
place it with a new one.
5. Your extension cable must be uncoiled, coiled cables can
overheat and reduce the efficiency of your product.
6. Do not pull cable around sharp objects.
7. Always switch off at the mains before disconnecting any
plug, cable connector or extension cable.
8. Switch off before removing or fitting the collection box.
9. Switch off, remove plug from mains and examine electric
supply cable for damage or ageing before winding cable for
storage. Do not repair a damaged cable, replace it with a
new one. Use only Flymo replacement cable.
10.Always wind cable carefully, avoiding kinking.
11.Never pull on the cable to disconnect any of the plugs.
12.Use only on AC mains supply voltage shown on the
product rating label.
Preparation
1. Always wear suitable clothing, gloves, and stout shoes. Avoid
wearing loose-fitting clothing or that has hanging cords or ties.
2. Obtain and wear safety glasses at all times.
3. Before using the machine check that all screws, nuts, bolts
and other fasteners are properly secured and guards and
screens in place and in good working condition.
4. Replace damaged or unreadable warning and operat-
ing labels.
5. Before starting the product, make certain that the feed inlet
is empty.
6. Do not operate the product in the vicinity of bystanders.
Use
1. Use the product only in daylight or good artificial light.
2. Operate the product only on a firm, level surface.
3. Do not allow hands or any other part of the body or clothing
inside the feed inlet or near any moving part.
4. Keep face and body away from the feed inlet opening.
5. Keep a proper balance and footing at all times. Do not over-
reach. Never stand at a higher level than the base of the
product when feeding material into it.
6. When feeding material into the product be extremely careful
that pieces of metal, rocks, bottles, cans , ropes, netting or
other foreign objects are not included.
7. When feeding material into the product be extremely careful
that the mains cable is not accidently fed into the product.
8. Keep hands and feet away from the cutting means at all times
and especially when switching on the motor.
9. Do not touch the cutting means before the machine is
disconnected from the supply and the cutting means
have come to a complete stop.
10. Do not tilt product when the power source is running.
11.Do not fold product when the power source is running.
12.When folding the product for storage please ensure the
mains cable is kept clear.
13.Whilst using the product ensure the cable does not be-
come trapped under the wheels or support feet.
14.Do not allow processed material to build up in the discharge
area. This may prevent proper discharge and can result in
kickback of material through the feed opening.
15.Use only Approved Replacement Parts.
16.Remove the plug from the mains :
- before leaving the product unattended for any period or
when transporting;
- before clearing a blockage;
- before checking, cleaning or working on the product;
- if the product starts to vibrate abnormally or makes an un-
usual noise. Check immediately. Excessive vibration can
cause injury.
Maintenance and storage
1. Keep all nuts, bolts and screws tight to be sure the product
is in safe working condition. Do not attempt to repair the
product unless you are competent to do so.
2. Check the collection box frequently for wear or deterioration.
3. Replace worn or damaged parts for safety.
4. Only use the replacement parts specified for this product.
5. Be careful during folding of the product to prevent en-
trapment of the fingers between moving and fixed parts
of the machine.
6. Store in a cool dry place and out of reach of children.
Do not store outdoors.
7. Allow the product to cool for atleast 30 minutes before
storing.
IMPORTANT
If you want to use an extension cable when operating
your product, only the following cable dimensions
should be used:
- 1.5 mm 2 : max length 25m
- 2.5 mm 2: max length 40m
Minimum rating :
1.5mm2 size cable, 16 amps 250 volts AC.
•YOUR PRODUCT IS SUPPLIED WITH CABLE WIRED
DIRECTLY INTO THE PRODUCT.
1.Do not wire an extension cable directly to your product your-
self. Please contact your local Approved Service Centre for
further information on the connectors and kits available.
2.Only use extension cables specifically designed for outdoor use.
3.Only use 1.5mm2 3 core extension cable.
MAINS PLUG REPLACEMENT
•If the plug supplied is cut off it should be destroyed.There
is an electric shockhazard if a cut off plug is inserted into
a 13 amp socket.
1.Ensure the mains voltage suits your product
2.IMPORTANT! The wires in the mains lead are
coloured in accordance with the following code:
BLUE - NEUTRAL BROWN - LIVE GREEN/YELLOW
- EARTH
The wire which is coloured BLUE must be connected
to the Terminal which is marked with the letter 'N' or
coloured BLACK. The wire which is coloured BROWN
must be connected to the Terminal which is marked
with the letter 'L' or coloured RED. The wire which is
coloured GREEN/YELLOW must be connected to the
Terminal which is marked with the ‘earth’ symbol.
4.It is important that the outer sheath is clamped cor-
rectly into the 3-pin plug.
5.If in doubt consult your local Service Repairer or quali-
fied electrician before the machine is used.
6.A 13 Amp fuse must be fitted to the Mains Plug.
7.The normal plug fuse and household fuse only protect
the electrical equipment and are not a safeguard
against electrocution.
Cable Information

A1
1. Attach the wheel and washer onto the axle (A1) ensuring the wheel is secured with the
retaining pin (A2). Attach the hub cap, ensuring the clips and holes are aligned before
securing into place. Repeat on the other side.
2. Using the spanner provided, attach the support foot with the support foot bolt, washer
and nut as illustrated in pic. A3. Repeat on the other side.
3. Attach the cable hook to the product as illustrated in pic A4. Repeat for the other three
cable hooks. This enables the mains cable to be wrapped around the product for stor-
age and transportation (C).
Preparation
1. Unfold the product by sliding the catch (B1) and un-
folding through 90o (B2) until it locks into the operat-
ing position.
2. The product can be transported to the required loca-
tion by holding the transport handle (C1) and tilting it
onto the wheels. as illustrated in pic C.
3. Before operating the product, ensure the collection
box is correctly located and the Interlock Switch (D1)
is securely in place. The product will not start if the In-
terlock Switch is not located correctly.
Assembly
A3A2
BC
90o
D
1
1
1
2
A4
Starting and Stopping
•Before starting,ensure that the Feed Inlet is empty
Starting
1. Unwind mains cable from around product and connect
to mains supply.
2. To start the product, turn the control switch clockwise to
the symbol (E1).
Stopping
1. To stop the product, turn the control switch
anti-clockwise back to the O symbol (F1).
E
1
F
1

Use
Feeding in Garden waste
1. Feed the material to be shredded into the Feed Inlet (G1).
The material is pulled in by the cutting blade automatically.
• Caution! Do not feed garden building waste such as,
sawn timber, fencing and decking.
• Caution! Long material standing out from the machine
could swing out when being pulled in by the blades!.
Maintain a safe distance!
Suitable Items to be shredded:-
• Twigs and branches – max. diameter 40mm;
• Waste from pruning bushes;
• Waste from hedge trimmings
• Plant parts.
2. A push stick is provided to feeding less bulky material
into the Feed Inlet (G2) enabling the material to reach
the cutting blade.
•Do not use any other object to push material into the
Feed Inlet.
Overload Reset Button
Overloading, jamming the product causes the machine to au-
tomatically stop.After a short period of time,press the reset
button (H1) and restart the product.
•When the feed inlet is suddenly blocked,the direction or rota-
tion may switch automatically.Stop the product and after a
short period of time,restart.
Clearing a Blockage
The product is fitted with a reverse switch (J1) to enable the
release of jammed material. Turn the control switch anti-
clockwise to the symbol to put into reverse mode.
G
12
J
1
Compost
Compost is a natural fertiliser. It can loosen clay soils and
can help sandy soils retain water.The organic matter in com-
post provides food for the microorganisms that keep your
soil healthy and in a balanced condition.These microorgan-
isms will naturally produce the Nitrogen, Potassium and
Phosphorus your garden requires.
The waste you are composting requires the correct ratio of
carbon rich materials (Browns) and nitrogen rich materials
(Greens).Too much Brown material will increase the conver-
sion time.Too much Green material and your compost will be
damp, solid and release unpleasant odours.
How does my Shredder help composting?
Shredders can produce large quantities of Greens and
Browns, which you could not normally compost. It will
speed up the composting process by reducing the size
and increasing the surface area of the material.
Shredded Browns, fibrous materials, provide body to the
final product and supply trapped air to the composting
creatures.
Shredded Greens, Soft Sappy materials, provide the en-
ergy for the composting creatures.
When will the compost be ready for use?
The compost may be ready in as little a 2 months or as much
as 12 months. It depends on the materials used, the compost
mix, air temperature and how much material was shredded.
The compost can be used when it has turned a dark
colour and the original ingredients are no longer
recognisable.
Do Compost
Kitchen Waste
Fruit
Vegetables
Teabags
Coffee Grounds & Filters
Egg Shells
Sawdust
Peanut Shells
Other
Washed Seaweed
Hay/Straw
Paper & Cardboard
Wood Ash
Manure from Vegetarian Animals
Garden Waste
Tree Prunings*
Twigs*
Plants*
Bush Prunings*
Hedge Trimmings*
Vegetable Waste*
Leaves*
Flowers*
Roots*
Grass Cuttings
Do Not Compost
Kitchen Waste
Meat
Fish
Cooked Food Wastes
Dairy Products
High Fat Foods
Other
Vacuum Cleaner Contents
Plastic Glass or Metal
Manure from Carnivorous Animals
Coal Ash
Household or Building Waste
Garden Waste
Soil
Poison Ivy
Poison Oak
Weeds
Diseased Plants
* Suitable for Shredding
H
1

Adjustment
•Important:- Only adjust the Cutting Plate when the
product is running. Failure to do so may lead to seri-
ous damage to your product and result in your War-
ranty becoming void.
Adjusting the Cutting Plate
If branches and twigs are not being cut through cleanly,
then adjustment of the Cutting Plate against the Cutting
Blade is required.
1. With the product running in the forward direction insert
the hex key supplied into the hole at the side of the
casing (N1).
2. With the product running in the forward direction turn
the hex key very slowly in a clockwise direction until
the Cutting Blade (P1) can be heard slightly touching
the Cutting Plate (P2) Do not over adjust,doing so
could cause serious damage to the Cutting Plate and
Cutting Blade and result in your Warranty becoming void.
3. Feed a branch into the Feed Inlet to check that it is cut
cleanly and that no further adjustment is required.
P
N
•Important
Switch off product before removing the Collection Box.
The Collection Box is a safety guard that prevents access
to the cutting blades.The product should never be used
without the Collection Box in place.
Removing the Collection Box
1. Pull down the Interlock Switch on the Collection Box
(K1). The product will not operate when this Interlock
Switch is open.
2. Hold the handle on the Collection Box and pull out
from under the shredding unit (L).
3. Empty the Collection Box.(M).
Fitting the Collection Box
1. Push the Collection Box under the shredding unit.
2. Push up the Interlock Switch on the Collection Box
(K1) until it clicks securely into position.
• IMPORTANT ! The Product will not operate if the Inter-
lock Switch on the Collection Box is not lifted upwards
into position.
LM
K
Collection Box
1
1
1
2

Caring for your Shredder
T
QR
1
S
Cleaning
•USE GLOVES
•IMPORTANT It is very important that you keep your product
clean. Debris left in any of the air intakes or under the product
could become a potential fire hazard.
1. With a brush, remove any debris from the Feed Inlet (Q)
2. Wipe over the surface of your product with a dry cloth (R).
3. Using a soft brush remove debris from all air intakes
(S).
4. Remove the Collection Box as described in the Collec-
tion Box section above.
5. Fold the product by sliding the catch (T1) and folding through
90o (V) until it locks into the storage position.
6. Remove debris from the discharge area with brush.(W)
7. Remove debris from the grass box with a brush (X).
•IMPORTANT Never use water for cleaning your product.
Do not clean with chemicals, including petrol, or solvents -
some can destroy critical plastic parts.
Storing your Shredder
1. Unfold your product back into the operating position,
replace the collection box and then fold into the stor-
age position.
2. Before folding make sure that the electric cable is
wound around the product properly (Y1).
3. Replace any Bolts, Nuts or Screws, if necessary.
4. Product must be stored upright as illustrated (Y1)
V90oW
XY
1
Fault Finding Hints
Fails to Operate
1. Is the correct Starting procedure being followed? See
‘Starting & Stopping’
2. Has the product overloaded ? See ‘Use’
3. Is the Power Turned On?
4. Is the Interlock Switch engaged?. See ‘Collection Box’
5. Check the fuse in the plug, if blown replace.
6. Fuse continues to blow?
Immediately disconnect from the mains electricity supply and
consult your local approved Service Centre.
Debris Material is not pulled into the cutter.
1. By using the Push Stick, ensure the material is fed far
enough into the Feed Inlet
2. Ensure the Cutter is adjusted correctly, see ‘Adjustment’
3. Is the product running in the forward direction.?
4. If problem persists?
Immediately disconnect from the mains electricity sup-
ply and consult your local approved Service Centre.
Poor Cutting of Debris Material
1. See ‘Adjustment’
2. If poor cutting persists.
Immediately disconnect from the mains electricity supply and
consult your local approved Service Centre.
Debris Material is jammed in the Feed Inlet
1. Set the start switch to reverse.
2. Ensure the material is not too thick for the product. Max di-
ameter of twigs and branches is 40mm.
3. If problem persists?
Immediately disconnect from the mains electricity supply and
consult your local approved Service Centre.
Excessive Vibration
1. Disconnect from the mains electricity supply.
2. Ensure the Cutter is adjusted correctly, see ‘Adjusting
the Cutting Plate’
3. If vibration persists?
Immediately disconnect from the mains electricity supply and
consult your local approved Service Centre.

If any part is found to be defective due to faulty manufac-
ture within the guarantee period, Husqvarna UK Ltd.,
through its Authorised Service Repairers will effect the
repair or replacement to the customer free of charge pro-
viding:
(a) The fault is reported directly to the Authorised Re-
pairer.
(b) Proof of purchase is provided.
(c) The fault is not caused by misuse, neglect or faulty
adjustment by the user.
(d) The failure has not occurred through fair wear and
tear.
(e) The machine has not been serviced or repaired,
taken apart or tampered with by any person not au-
thorised by Husqvarna UK Ltd..
(f) The machine has not been used for hire.
(g) The machine is owned by the original purchaser.
(h) The machine has not been used commercially.
* This guarantee is additional to, and in no way dimin-
ishes the customers statutory rights.
Failures due to the following are not covered, therefore it is
important that you read the instructions contained in this
Operator's Manual and understand how to operate and
maintain your machine:
Failures not covered by guarantee
* Replacing worn or damaged blades
* Failures as a result of shredding inapropriate material.
* Failures as a result of incorrect adjustment of the cut-
ting plate
* Failures as a result of not reporting an initial fault.
* Failures as a result of sudden impact.
* Failures as a result of not using the product in accor-
dance with the instructions and recommendations
contained in this Operator's Manual.
* Machines used for hire are not covered by this guaran-
tee.
* The following items listed are considered as wearing
parts and their life is dependent on regular mainte-
nance and are, therefore not normally subject to a
valid warranty claim: Blades, Electric Mains cable,
Cutting Plate
*Caution!
Husqvarna UK Ltd. does not accept liability under the
warranty for defects caused in whole or part, directly or in-
directly by the fitting of replacement parts or additional
parts that are not either manufactured or approved by
Husqvarna UK Ltd., or by the machine having been modi-
fied in any way.
Service Recommendations
Guarantee & Guarantee Policy
1. We strongly recommend that your product is serviced
at least every twelve months, more often in a profes-
sional application.
2. Always use genuine Flymo Spare Parts.
3. Prepacked spares are available from most Husqvarna
UK Ltd. stockists.
4. Your product is uniquely identified by a silver and
black product rating label
5. If you have a problem with your machine contact your
local Approved Service Centre ensuring you have full
details of your product as described on the product
rating label.
6. Should it be necessary for workto be carried out by your Serv-
ice Centre,it is important to take your complete machine in-
cluding cable and any extension cables used.
A network of specialist dealers can be found in your localYel-
low Pages. To obtain service on your Flymo product simply
telephone or visit your local Service Centre.
Should you require service under the terms of our guarantee
the Service Centre will require proof of purchase.
All of the centres listed stockgenuine Flymo Spare Parts.
NOTE: Our Service Repairers act on their own behalf
and are not empowered to commit or legally bind Husq-
varna UK Ltd. in any manner whatsoever.
Environmental Information
• Awareness of the environment must be considered
when disposing of ‘end-of-life’ product.
• If necessary, contact your local authority for disposal
information.
The symbol on the product or on its packaging
indicates that this product may not be treated as household
waste. Instead it shall be handed over to the applicable
collection point for the recycling of electrical and electronic
equipment.
By ensuring this product is disposed of correctly, you will
help prevent potential negative consequences for the
environment and human health, which could otherwise be
caused by inappropriate waste handling of this product.
For more detailed information about recycling of this
product, please contact your local council office, your
household waste disposal service or the shop where you
purchased the product.

5051397-03
EC Declaration of Conformity
Husqvarna AB, 561 82, Huskvarna, Sweden
Declare under our sole responsibility that the product(s);
Category............................Electric Garden Shredder
Type(s) ............................PAS2500
Identification of Series.......See Product Rating Label
Year of Construction..........See Product Rating Label
Conforms to the essential requirements & provisions of the following EC Directives:
2006/42/EC, 2004/108/EC, 2000/14/EC
based on the following EU harmonized standards applied:
EN60335-1, prEN50434, EN13683, EN50366, EN55014-1, EN61000-3-2, EN61000-3-11
The maximum A weighted sound pressure level LpA at the operator’s position, recorded on a sample of the above prod-
uct(s) corresponds to the Level given in the table.
The maximum hand / arm vibration weighted value measured according to EN ISO 20643 on a sample of the above
product(s) corresponds to the Value
ah given in the table.
2000/14/EC: The Measured Sound Power LWA & Guaranteed Sound Power LWA values are according to the tabulated
figures.
Conformity Assessment Procedure............... Annex VI
Notified Body................................................. Intertek, Cleeve Road
Leatherhead, Surrey
KT22 7SB, England
Newton Aycliffe 26/09/2011
M.Bowden
Global R & D Director - Walk behind
Keeper of Technical Documentation
EN 61000-3-11 Compliance statement
Depending on the characteristics of the local electricity supply network, use of this product may result in short voltage
drops at the instant of switching on. This may influence other electrical equipment e.g a momentary dimming of a lamp.
If the Mains impedance Zmax of your electricity supply is less than the value shown in the table (applicable to your
model) then these effects will not occur. The value of the network impedance may be determined by contacting your
electricity supply authority
Type
Width of Cut (mm)
Speed of Rotation of Cutting Device (rpm)
Power (kW)
Measured Sound Power LWA (dB(A))
Guaranteed Sound Power LWA (dB(A))
Level LpA (dB(A))
Uncertainty KpA(dB(A))
Value
ah (m/s2)
Uncertainty Kah (m/s2)
Weight (Kg)
Mains Impedance Zmax (Ω)
PAS2500
40
40
2.5
97
98
85
2.5
2.40
1.5
33.5
0.314
Husqvarna AB
561 82
Huskvarna
Sweden
Our policy of continuous improvement means that the specification of products may be altered from time to time without prior notice.
Copyright © 2011 Flymo S.A. All rights reserved. Flymo® and other product and feature names are registered or unregistered trademarks
of Flymo S.A.