Foc.us Mc-735 User manual

Models:

MC-735/735DMF/735DMT

MC-760/760DMF/760DMT

Detection Range 12m (MC-735)

15m (MC-760)

Input Voltage 9-16VDC

Current Drain about 15mA/12VDC

PIR section:

Optical lens data

PIR area: 22+12+6+4(MC-735)

44+12+6+4(MC-760)

Max coverage:12m*12m(MC-735)

15m*15m(MC-760)

Trigger indication: indicator twinkling

for about 10 sec.

Alarm and tamper

Alarm output: solid state relay,

NO 50mA/30V

The circuit will be open when alarm.

Alarm indication: LED on.

Event counter:optional,1-2 moving event.

Tamper interface: NO,50mA/30VDC

2.Specifications

Mounting

Surface or corner,at the height of 1.8 to 2.4 m

Note: Base allows single-sided corner mount at 45 to wall

Accessories:

BR-1:Surface mounted swivel bracket, adjustable 30

down and 45 left or right.

BR-2:BR-1 with a corner adapter

BR-3:BR-1 with a ceiling adapter

Environment:

Operating Temperature: -10 C to 50 C(14 F to 122 F )

Storage Temperature :-20 C to 60 C (-4 F to 40 F)

Anti whitelight: 9000 LUX

Physical

Size(H*W*D):112*59*41 m m

This device is coherent to Europe parliament direct 1999/5/EC

necessary items and rules, and also coherent to the main spirits

of radio and telecom terminal equipments on March 9 . 1999.

The device also reaches the Canadian standard RSS-210. It can

be used indoor and outdoor, which can reach its maximum prote-

ction and avoidance of above interference.

3.Installation

3.1 General Guidelines

Don't face cold or heat

source directly

Do not open window

of the saved area. Do not mount it

outdoor.

Don't face the

sun shine directly

Wire connection or

detector can't be near

to high-pressure cable

Don't install on a

unstable base.

The installation height of the detector

is 1.8-2.4 meters can Anti-pests

3.2Anti-pests installation

Never face the detector to the place that

pests can climb up directly

The upper part of the detection

area is non anti-pests area

1.Introduction

MC-735 is a digital micro-processing dual-tech detector adopting the technology

of DMF(digital memory focus ).DMT (dynamic matrixing time) .that can be

applying to decorative indoor with small size and flown line figure .The PIR parts

adopt column fresnel lens to effect of energy-receiving and four-layer screening

technology to anti blind-corner. Its advanced true motion recognition function .

anti-pets function can prevent wrong alarm to 15 kg pets or 5 cats .insects .mouse

or birds etc. It won’t trigger wrong alarm or miss alarm so it is far excellent in

function than common detectors. It can be used for different kind of indoor. With

the built-in large capability battery and exclusive circuitsave up powerl.

MC-735/760 intelligent with PIR

intrusion detector installation manual

WALK-

TEST

LED

LENS

PIR

SENSOR

LED

switch

SINGLE OR

DOUBLE

SELECTION

JUMPER

LED

Figure 1.General View Figure 2.Inside View

Suggestion angle

installation

B. Insert the wireline to

base through bacl slot

The detector will be in a visible area spy mode automatically after 3 minutes

of power connect. And adjust JUMPER to choosethe PIR function testing soley

or simultaneously.

Step-check LED lighting

Normal working state (LED on)

3.3Illustrated Installation Procedure

3.3.1 Disassemble unit

3.3.2 Mount base

1.8-2.4m 6-8ft above ground

Singleside45

angled side

Surface

mount

(1 of 2)

A. Mark the drilling points

and drilling the wall

C. Insert two dowels and

attach the base to the wall

with two screws

D.Insert the bottom edge of

the large PCB under this

TAB & Press the top edge in

3.10 Perform motion test to the detection area: install the cover and close the fasten part

(refer to the right diagram)

1. Start the test at least 2 minutes after power supply

2. Crossing to any direction of the detection area, your walking with 0.75m/s will cause the LED

indicator to light for 2-3 seconds (refer to the right diagram)

3 .Perform motion test from contrary directions in order to confirm the boundary of two sides. Make

confirmed that detection center pointing to the center of protected area.

4. Away from the detector 3 to 6 m, raise slowly your arm and reach into the detection zone, mark the

lower limit of PIR detection. Do the same step to confirm the upper limit.

5.the center of detection zone should not uphill incline. To obtain a good detection range , please adjust

the vertical detection range, en-sure the detector is in a correct position.

6. After MW sensitivity or detection angle are adjusted, walking test

must be performed according to the above steps.

Even the most sophisticated detcetors can sometimes be defeated or may fail to warn due to :DC power failure/improper connection, malicious mask-

ing of the lens,tampering with the optical system, decreased sensitivity in ambient temperatures near that of the human body and unexpected fail-

ure of a component part.The above list includes the most common reasons for failure recommended that the detector and the entire alarm system be ch-

ecked weekly, to ensure proper performance.An alarm system should not be regarded as a substitute for insurance. Home & property owners or renters sh-

ouldbe prudent enough to continue insuring their lives & property, even though they are protected by an alarm system.

WARNING! Changes or modifications to this unit not expressly approved by the party

responsible for compliance could void the user s authority to operate the equipment.

This device has been tested and found to comply with the limits for a Class B digitaldevice, pursuant harmful interference in residential installations .This equipment

generates,uses and can radiate radio frequency energy and ,if not installed and used in accordance with the ins-tructions ,may cause harmful in-terference to radio and t-

elevision reception. However, there is no guarantee that interference will not occur in aparticular installation .If this device does cause such interference , which can be ver-