Focal point Como l23 User manual

INSTALLATION INSTRUCTIONS

All instructions must be handed to the user for safekeeping.

Revision A - 05/07

Country(s) of destination - GB/IE

COMO

MODEL : L23

WALL MOUNTED FLUELESS GAS FIRE

Focal Point Fires plc, Christchurch, Dorset BH23 2BT

Tel: 01202 499330 Fax: 01202 499326

www.focalpointfires.co.uk

e-mail: sales@focalpointfires.co.uk

It is the LAW that all gas appliances and fittings are installed by a competent person (such as a CORGI registered fitter) and in

accordance with the Gas Safety (Installation and Use) Regulations 1998.

INSTALLATION INSTRUCTIONS

IMPORTANT NOTES

This appliance is a high efficiency, flueless catalytic flame effect gas fire. It provides radiant and convected warmth

both efficiently and safely utilising the latest type catalytic converter and burner technology. The appliance does not

require a flue system of any type as the catalytic converter cleans the flue products to provide a complete combus-

tion system, which is intrinsically safe. It is designed to operate on Natural Gas and is factory set for operation on

the gas type, and at the pressure stated on the appliance data plate.

The appliance incorporates a combustion monitoring system (Oxygen Depletion System). It must not be adjusted

or put out of operation. If replaced then manufacturers original parts must be used.

It is the LAW that all gas appliances and fittings are installed by a competent person and in accordance with the Gas

Safety (Installation and Use) Regulations 1998, the relevant British Standards for Installation, Codes of Practice and

the Manufacturers' Instructions. At the time of writing, CORGI registered operatives are the only class of person

considered as 'competent' by the HSE under the above regulations.The installation shall also be carried out in accor-

dance with the following:

• Manufacturers' Instructions.

•The Building Regulations issued by the Department for Communities and Local Government, the Building

Standards (Scotland) (Consolidation) Regulations issued by the Scottish Development Department.

•Relevant British standards insofar as the relevant areas are not covered by these instructions.

•For Republic of Ireland, reference should be made to the current edition of IS813 (the relevant standards

governing installation).

Failure to comply with the above could lead to prosecution and deem the manufacturer’s warranty invalid.

This appliance must be installed in accordance with the rules in force and used only in a sufficiently ventilated space.

The appliance is designed to fit various types of situations as described in sections 3.0 and 4.0.The appliance must

be installed in a correctly sized room (see section 3.1), and the correct purpose provided ventilation must be pro-

vided (see section 4.1).

It should be noted that heaters create warm air currents. These currents move heat to wall surfaces next to the

heater. Installing the heater next to vinyl or cloth wall coverings or operating the heater where impurities in the air

(such as tobacco smoke, candle smoke etc.) exist, may cause the walls to become discoloured.

This appliance is intended as a secondary source of heat only and should not be used in a room without some form

of background heating present. If the appliance is used in a room as the sole source of heat, then condensation may

occur on colder surfaces within the room.

On first light up of a new appliance, initial curing of high temperature paint and burning off of lubricants may occur

for the first few hours of operation. During this period some smoke may be emitted from the outlet grille, this should

be no cause for concern. Accordingly, the room should be well ventilated with all windows and doors open during

this period. During this period the appliance may cause smoke alarms to sound. If this happens, reset the alarms, but

do not remove the batteries.

Consult ALL instructions before installation and use of this appliance. This appliance is free from any asbestos mate-

rial.

Except where otherwise stated, all rights, including copyright in the text, images and layout of this booklet is owned

by Focal Point Fires plc.You are not permitted to copy or adapt any of the content without the prior written per-

mission of Focal Point Fires plc. 1

Section Contents Page No.

1.0 Important Notes 1

2.0 Appliance Data 2

3.0 Installation Requirements 2

3.1 Room Sizing 2

4.0 Site Requirements 2

4.1 Ventilation 3

5.0 Unpacking the Appliance 4

5.1 Component Checklist 4

6.0 Gas Supply Routes 4

7.0 Fixing the Appliance 5

7.1 Checking the Burner 5

Section Contents Page No.

8.0 Testing and Commisioning 6

8.1 Operating the Appliance 6

8.2 Spark Failure 6

8.3 Setting Pressure 6

8.4 Fitting the Decorative Frame 7

9.0 Briefing the customer 7

10.0 Servicing 7

10.1 Servicing the Burner Unit 8

10.2 Pilot Assembly 8

10.3 Catalysts 8

10.4 Testing for Firebox Leakage 9

11.0 Troubleshooting Guide 10

1.0

INSTALLATION REQUIREMENTS

If the appliance is to be sited near a disused or unserviceable fireplace served by a natural draught flue then the old

flue must be sealed off. It will be necessary to ventilate the old flue to prevent condensation and dampness forming,

however any air vent used to ventilate the old flue must not be sited within 500mm of this appliance. If the flue can

be ventilated to the outside of the building then this is usually the best solution. If in doubt then advice should be

sought from a local building control officer. The appliance is designed to be wall mounted. If the appliance is to be

mounted on a newly fabricated area of wall that also serves the purpose of sealing off the old flue then it is very

important that there are no holes, gaps or otherwise in this wall that will allow draughts from the old flue to enter

the room, especially directly behind the appliance. Such draughts could affect the performance of the ODS system

and result in nuisance cutting out, for example. If the gas supply pipe is to enter the appliance from the rear, i.e.

emerge from the wall behind the appliance then any hole in the wall from which the pipe emerges must be tightly

sealed.

Any existing under grate draught device should be sealed off to prevent loss of heat or creation of draughts. It is

possible to install the appliance onto certain types of combustible materials - see section entitled 'Clearances to

combustible materials'.

ROOM SIZING

The room size should be a minimum of 23m3(e.g. 10’1” x 10’1” x 8’) to allow adequate circulation of air and ensure

the correct operation of the fire.This volume may include adjacent spaces but these spaces must not be separated

by a door.To calculate a room size in cubic metres (m3) divide the room volume in cubic feet (ft3) by 35.3.

SITE REQUIREMENTS

This appliance is designed to be wall-hung. Do not recess any part of the appliance into the wall.

This Appliance may be installed in any room in a home, however there are exceptions, and the appliance may not be

used in bedrooms or bathrooms.

Installation in living rooms is common, however other rooms such as kitchens, dining rooms and hallways are per-

mitted, providing a suitable natural gas supply is available, and rooms sizing and ventilation requirements are strictly

adhered to (see sections 3.1 and 4.1).

The appliance is designed to be versatile, and as such will operate correctly when exposed to normal gentle draughts

experienced within the home. It is not recommended, however that the appliance be installed in areas where it is

likely to be exposed to persistent strong draughts, that may be generated by outside doors or windows, air vents

etc. It is recommended that the appliance should not be installed within 1 metre of any air vent.

APPLIANCE DATA

Gas Group G20 Natural Gas CAT I2H

Inlet Pressure 20 mbar (± 1.5 mbar)

Max Energy Input Gross 2.0 kW

Net 1.8 kW

Max Gas Rate 0.20 m3/h

Min Energy Input Gross 1.3 kW

Net 1.15 kW

Pilot Energy Input Gross 166 W

Net 150 W

Burner Pressure High 17.3 mbar. (± 1.0 mbar). Hot

17.5 mbar. (± 1.0 mbar). Cold

Low 8.3 mbar. (± 0.5 mbar). Hot

8.0 mbar (± 0.5 mbar). Cold

Main burner flow restrictor Stereo 1.03mm (1/4” BSP)

Oxypilot SIT/Bray 9082

Gas Inlet Connection 8mm inlet restrictor elbow

Ignition Piezo spark

Spark Gap 4.0 mm (± 1.0mm)

Please see Data Badge affixed to appliance for current data.

This appliance is for use only with the gas type, and at the pressure stated on the appliance Data Badge.

2.0

3.0

3.1

4.0

SITE REQUIREMENTS (continued)

Clearances to non-combustibles

Non combustible surfaces are defined as brick, metal, marble, concrete etc. and also a number of man-made mate-

rials impervious to flame. If in doubt refer to the material manufacturer for further information before proceeding

with installation.

Clearances to the sides of the appliance are 100mm (4”). Clearance to the front of the appliance is 500mm (20”).

The back of the appliance may be installed directly onto a non-combustible wall, providing the area behind the appli-

ance is flat and does not interfere with the various vent holes in the back panel of the appliance.

A non combustible shelf of any depth may be positioned above the appliance provided it is no closer than 400mm

from the top of the appliance glass panel and the wall above the appliance is non combustible.

The appliance must not be positioned vertically within 60mm ( 2.4”) of a solid floor (i.e. wood or stone) or hearth.

This dimension is measured vertically to the bottom of the appliance firebox.

Clearances to combustible materials

Combustible materials are defined as wood, fabrics, or other materials likely to combust if exposed to flame.

Generally, any material, which is likely to discolour, melt or misshape when exposed to moderate heat, should be

considered as a combustible material or surface.

Clearance to the sides of the appliance are 100mm (4”) but curtains, drapes and other fabrics are not permitted

within a distance of 500mm(20in) of the appliance sides. No such materials are permitted directly above the appli-

ance regardless of distance.

The minimum clearance to the ceiling above the appliance is 800mm (31.5”) measured from the top of the appliance

glass panel.

Combustible materials should not be positioned directly in front of the appliance within a distance of one metre.

Under no circumstances should any electrical equipment e.g. plasma screen TV sets etc. be positioned on the wall

above the appliance. The appliance is designed to be wall mounted alone and not in conjunction with any type of

combustible fire surround. No combustible shelves should be positioned on the wall above the appliance. It should

be established that any mirrors or picture frames etc. to be positioned on the wall above the appliance are able to

withstand prolonged exposure to moderate heat and moisture before proceeding with their installation.

The back of the appliance may be installed directly onto a combustible wall, providing it is relatively flat and does not

interfere with the various vent holes in the back panel of the appliance.The wall must be structurally sound and con-

structed from a material capable of withstanding moderate heat. Brick, concrete, finished plaster, most types of con-

ventional wall paper and dry-lined plasterboard are examples of suitable materials. Materials such as flock, blown

vinyl and embossed paper which are sensitive to even small amounts of heat should be avoided as scorching and or

discolouration may occur over time.

If the appliance is to be mounted on a dry lined wall or a timber framed construction wall then the integrity and

ability of the wall to carry the weight of the appliance must be confirmed. It is important in these circumstances that

any vapour control barrier is not damaged, and that any structural members of the house frame are not damaged -

refer to section 7.0.

The appliance must not be positioned vertically within 100 mm (4”) of a carpeted floor, rugs or fabric materials of

any kind. This dimension is measured vertically to the bottom of the appliance firebox.

VENTILATION

A minimum of 100 cm2purpose provided ventilation is required for this appliance.This may be achieved either with

one vent 100 cm2at a high or low position in the room, or split ventilation i.e. 50cm2 be installed at high level and

50cm2 be installed at low level within the room. An openable window or equivalent is also required.The require-

ments of other flued appliance operating in the same room or space must be taken into consideration when assess-

ing ventilation.

Any ventilation fitted must comply with BS 5871 part 4 and BS 5440 part 2. Ventilation fitted under, or within imme-

diate vicinity of the appliance must not be used as it may adversely effect performance of the ODS system.The appli-

ance MUST NOT be installed in a bedroom, bathroom or any sleeping area. For Republic of Ireland, see relevant

rules in force. The appliance should not be installed within 1 metre of any air vent.

4.0

4.1

UNPACKING THE APPLIANCE

Remove the outer packaging, remove any instructions or fixing kits.

Read ALL these instructions before continuing to unpack or install this appliance.

Lift off the remaining packaging components and remove the contents of the box.

Check that the components supplied correlate with the component checklist. Please dispose of all the packaging

materials at your local recycling centre.

COMPONENT CHECKLIST

QUANTITY DESCRIPTION

1 Firebox and burner assembly

1 Set of manufacturers instructions

1 Decorative frame assembly (FL05 models)

1 Decorative glass facia assembly (FL06 models)

1 Screw and wall plug pack

1 Rubber grommet

1 Fitting template

GAS SUPPLY ROUTES

There are four possible entry points for the gas supply pipework to enter the appliance firebox.These entry points

are ‘knock out’ type holes.

Non-concealed gas connections may be made using the entry points at either end of the firebox or the one in the

bottom of the firebox.A concealed gas connection may be made using the knock out hole in the centre back of the

firebox. Select the most appropriate entry point and knock out the relevant hole

No more than 1.5m of 8mm diameter pipe must be used to avoid unnecessary pressure drops.

If a concealed gas connection is to be made, the supply pipe

should always be sleeved through walls and floors using the

shortest possible route.

For concealed supply pipe routing, pipes must (where pos-

sible) be vertical and providing there is sufficient wall thick-

ness available, they should be placed in pipe chases.

Horizontal pipe runs should be avoided. Prior to chasing a

solid wall, an inspection should be made to note the prox-

imity of any cables/sockets outlets which may already be

buried.

Pipes must be secured using suitable clips and protected against corrosion. Ideally factory finished protected

pipework and fittings should be used. Joints should be kept to a minimum and compression fittings must not be used.

The pipework installation must be tested for soundness before any protection is applied and/or the pipework and

fittings are buried.

5.0

5.1

6.0

FIXING THE APPLIANCE

After having selected the final mounting position of the

appliance, taking into account the site requirements as

specified in section 4 of these instructions, the integrity

of the wall, and the feasibility of the proposed supply

pipe routing, the firebox of the appliance may be secured

to the wall. A fitting template is supplied to assist with

this.

Mark the positions shown as “Gas model L23G” on the

wall. If the appliance is to be mounted on the inner leaf

of a conventional cavity wall, or a solid wall, drill four

holes using a 6.5mm masonry bit. Insert the fibre

wallplugs provided.

If the appliance is to be mounted on a dry lined wall or

a timber framed construction wall then special cavity screw fixings will be required which are not supplied with this

product.These should be constructed from metal and not plastic.

If a concealed gas connection is to be made ensure the gas supply pipe is in it’s final position and can enter the appli-

ance in the correct position when the appliance is hung on the wall.

Insert the wall fixing screws into the top wall plugs, taking care to

leave the screws protruding approximately 5mm from the wall. Now

hang the appliance onto these screws through the two keyhole

shaped holes in the back panel of the appliance.

Insert the lower fixing screws into the lower wall plugs through the

corresponding fixing holes in the lower part of the back panel. Do

not tighten fully.

Before tightening the wall mounting screws fully, at this stage it is

recommended to check the horizontal alignment of the appliance

with a spirit level, as small adjustments can still be made if necessary.

When this has been checked, tighten all four fixing screws fully.

To access the upper fixing screws insert a screwdriver either

through the round holes in the front of the outlet grille, or alterna-

tively for easier access the outlet grille may be removed and the fix-

ing screws accessed more directly through the holes in the deflector

baffle as shown above.

CHECKING THE BURNER

There are no imitation fuel bed components to install.The appliance features a ribbon burner which is designed to

produce a continuous band of flame over it’s length.

The burner should be visually inspected to ensure it is free from any foreign matter.

If it is necessary to clean or dust off the burner then the glass door should be removed by removal of the four

retaining screws. Re-fit the glass door after cleaning or inspection, ensuring the correct orientation and a good

seal.

7.0

FIREBOX OUTLINE

F860060 ISSUE C - 16/8/06

WALL MOUNTED L23G,L27G & L23E

FITTING TEMPLATE

POSITION SPIRIT LEVEL ALONG THIS EDGETO LEVEL TEMPLATE BEFORE

MARKING OUT WALL

CENTRE LINE

IMPORTANT

THIS FIRE IS TO BE WALL HUNG ONLY.

DO NOT RECESS OR INSET ANY PART OF THE FIRE.

THIS TEMPLATE IS FOR THE MARKING OF FIXING POINTS ONLY.

DO NOT INSTALL THE FIRE WITHTHIS TEMPLATE IN PLACE.

GAS MODEL L23G

GAS MODEL L27G

PIERCE TEMPLATE

TO MARK HOLE

POSITION ON WALL X 4

CONCEALED

GAS INLET

FIXING POINTS FOR GAS MODEL L23G & L27G

349mm (13.74”)

405mm (15.94”)

28mm

(1.1”)

ELECTRIC MODEL L23E

PIERCE TEMPLATE

TO MARK HOLE

POSITION ON WALL X 3

326.5mm (12.85”)

FIXING POINTS FOR ELECTRIC MODEL L23E

419mm (16.5”)

FIXING POINT FOR

ELECTRIC MODEL

L23E

FIXING POINTS FOR GAS MODEL L23G & L27G

7.1

TESTING AND COMMISSIONING

Turn on and test the gas supply up to the fire for any leaks, in accordance with the current edition of BS6891.

OPERATING THE APPLIANCE

The pilot is visible behind the left hand side of the burner.

The control knob is located on the lower right hand side of the outer

case. It is of a spherical design and is marked as shown in the diagram

to the right;

Push in and turn the control knob to the SPARK position, and hold

there for a few seconds. Continue turning anti-clockwise through the

spark click to the PILOT light position, ensuring the pilot has lit. If not,

return the knob clockwise, and repeat.

When the pilot lights after the spark, keep the knob depressed for

approximately ten seconds. Now release the knob and the pilot should

stay alight. If the pilot is extinguished during use, wait three minutes

before repeating the ignition procedure.

To achieve the HIGH setting, push the control knob in slightly and con-

tinue turning anti-clockwise to the high position.The main burner should light after a few seconds. To decrease the

setting to LOW, turn the control knob clockwise to the low setting.

To turn to the PILOT position from the HIGH or LOW positions, press the control knob in, and return to the pilot

position and release.To turn the fire OFF, keep the knob pressed in, return to the off position and release.

SPARK FAILURE

The gap between the spark electrode and the pilot should be 3 - 5mm to produce a good spark. There should be

no need to adjust this. If under any circumstances the piezo electric spark fails, the pilot cannot be lit manually.

SETTING PRESSURE

The pressure test point is located on the left hand side of the appliance, on the main burner pipe, next to the brass

restrictor/connector. Release the setting pressure test point screw, and attach a U gauge. Light the fire on the HIGH

setting.

To commission the appliance, the burner pressure must be in accordance with the figures stated in the data section

of these instructions.

The fire is factory set to achieve these pressures and any significant variation could indicate a supply problem. If the

pressure is too high, the gas supply meter may be set incor-

rectly. This should be checked with the fire running and if

necessary reset by the gas supplier.

If the burner pressure is too low, then check the inlet pres-

sure with the appliance running. If this is less than approx-

imately 20mbar it will need to be reset by the gas supplier.

If the setting pressure is too low, but the meter pressure is

acceptable, then a problem in the supply pipework is to be

suspected.

This will be dirt and debris, kinked or inadequate size pipes,

restriction in a fitting, shut off elbow not fully open or sol-

der flashing across a joint. Identify the cause of the restric-

tion and rectify. Switch the fire off, disconnect the U gauge and refit the test nipple screw. Light the fire and check

for gas soundness.

In the event that the burner pressure is not in accordance with the figures stated in the data section of these instruc-

tions, the appliance must not be commissioned, and the manufacturer should be contacted for guidance.

8.3

8.0

8.1

8.2

‘OFF’ position

‘SPARK’ position

‘LOW’ position

‘HIGH’ position

FITTING THE DECORATIVE FRAME ASSEMBLY

Remove the mirrored facia panel from any

protective packaging. The glass facia panel

is supported by four M6 screws which

protrude from the front of the outer cas-

ing.

Ensure each screw is unscrewed approxi-

mately one turn from the fully screwed in

position in order to create a 2mm gap

(shown).

Simply hang the facia panel onto the outer

casing ensuring that the corresponding

keyhole shaped holes engage the screw-

heads fully.

BRIEFING THE

CUSTOMER

All instructions must be handed to the user for safekeeping. Show the customer how to light and control the fire.

After commissioning the appliance, the customer should be instructed on the safe use of the appliance and the need

for regular servicing. Frequency of service depends on usage, but MUST be carried out at least once annually.

Advise that cleaning of the fire maybe achieved when the fire is cold using a damp cloth and mild detergent on most

surfaces. Advise that the fire will emit a "newness" smell for a time after initial commissioning and that extra venti-

lation may be needed during this time. Recommend that a guard be used for the protection of the young, pets, the

elderly and the infirm.

SERVICING

Isolate the fire from the gas supply. Ensure that the fire is fully cold before attempting service.

A suggested procedure for servicing is detailed below.

1. Lay out the dustsheet and tools.

2. Remove the decorative frame/glass facia assembly. Removal is reverse of section 8.4.

3. Remove the glass door assembly (4 screws) and clean carefully.

4. Inspect the burner and the catalyst and clean if necessary with a soft brush.

5. Disconnect the gas supply.

6. Detach the burner front cover plate by removal of the four retaining screws. Undo the four

screws retaining the burner support brackets to the base and rear of the firebox. Remove the

control knob and spindle assembly from the valve by removal of the spindle retaining clip.

7. Remove the burner unit, strip off the burner pipes and clean thoroughly.

8. Clean the in-line restrictor, pilot assembly and the burner tube. Do not attempt to remove the

pilot injector as this can cause damage.

9. Re-assemble components.

10.Turn on the gas supply and leak test. Check pilot and burner for good ignition.

11. Refit the glass door assembly, ensuring correct orientation and a good seal.

12. Refit the decorative facia/frame assembly as detailed in section 8.4.

13. Check the purpose provided ventilation is un-obstructed.

14. Light the fire and test setting pressures.

15. Check safe operation of the appliance.

For specific servicing instructions, see relevant sections.

9.0

8.4

2mm

10.0

SERVICING THE BURNER UNIT AND GAS ASSEMBLY

Firstly, remove the decorative frame/glass facia assembly as described in section 8.4. Remove the inner glass panel,

and disconnect the gas connection inside appliance. The gas connections to the gas valve can now be released.

Detach the burner front cover plate by removal of the four retaining screws. Undo the four screws retaining the

burner support brackets to the base and rear of the firebox, and remove the control knob and spindle assembly by

removal of the spindle retaining clip.The burner may now be removed.

Remove the pilot and main burner pipes and blow through to dislodge any debris. Now remove the restrictor elbow

and blow through to make sure it is entirely clear.

Unclip the pilot lint gauze and clean with a soft brush. Clean the exterior of the pilot assembly with a soft brush and

blow through the flame ports on the pilot head. Check the aeration holes are free from lint or dirt.The pilot assem-

bly can be removed if required by disconnecting the electrode HT lead, gas pipe and unscrewing the mounting screws

and lifting away.

The pilot assembly is a non-serviceable item and should not be taken apart. Aeration holes must be absolutely clear

internally for proper operation. NEVER MODIFY OR BEND THE THERMOCOUPLE TO MAKE THE PILOT

STAY ALIGHT. Modifications are dangerous and can have serious unseen effects on safety. If the pilot will not stay

lit there is a problem with dirt, the gas supply to it, or the thermocouple needs replacement.

The gas valve is a non-serviceable item. If this needs replacement, remove M4 securing screw holding the valve in

place, remove all pipe unions, electrode lead, thermocouple lead and then the complete valve. Replacement must be

original manufacturers parts. Re-assembly is the reverse of removal. Ensure setting pressures are as stated in Section

2; Appliance Data.

PILOT ASSEMBLY

Clean the pilot assembly with a soft brush and blow through. Check the aeration holes are free of any dirt or lint.

Clean thoroughly internally, the connection can be removed from the base of the pilot unit using two spanners to

make cleaning easier. Do not damage or try to dismantle the pilot injector.

The unit is factory set and the only check necessary is to ensure the spark gap is correct. See specifications for gas

setting.

NEVER MODIFY OR BEND THE THERMOCOUPLE TO MAKETHE PILOT STAY ALIGHT. If the pilot will not

stay lit there is a problem with dirt, the gas supply, or the thermocouple needs replacement. Modifications are dan-

gerous and can have a serious unseen effect on safety and therefore MUST not be done. Replacements must be orig-

inal manufacturers parts. Re-assemble in the reverse of removal. Ensure setting pressures are as stated in Section 2;

Appliance Data.

CATALYSTS

It is recommended that the catalysts are inspected for signs of damage and dirt during routine servicing procedures.

The expected life of the catalysts is in excess of 11,000 hours (10 years of normal use). After this time the catalysts

should be replaced.

If there are any deposits of dirt or soot on the catalyst they should be cleaned with a soft brush and a vacuum clean-

er. If removed for cleaning ensure the seals are in good condition before replacing the catalyst. New seals will usu-

ally be required.

The performance of the catalysts may be checked using a combustion gas analyser as follows. Any analyser used

should conform to BS7927 : 1998 + A1 : 1999.

Ignite the fire as per the operating instructions, and run at maximum setting for 15 minutes. Position gas sample

probe directly over the catalysts via the outlet grille, on top of the appliance. Record the carbon dioxide (CO2) con-

centration and then the carbon monoxide (CO) concentration as displayed by the analyser - also noting the units in

which the values are expressed.

Most analysers display carbon dioxide (CO2) concentrations in percentage (%) terms and carbon monoxide con-

centration in parts per million (ppm) terms.

In order to calculate the combustion ratio for the appliance (CO/CO2) it is first necessary to express both gas con-

centrations in terms of percentage.To convert from parts per million (ppm) to a percentage (%) divide the ppm fig-

ure by 10,000. Examples : 35ppm = 0.0035%, 15ppm = 0.0015%, 5ppm = 0.0005%.

10.2

10.1

10.3

CATALYSTS (continued)

Now divide the concentration of carbon monoxide (CO) expressed in percent by the concentration of carbon diox-

ide (CO2) to obtain the appliance combustion ratio.

The combustion ratio of the gasses emitted by the catalytic convertor should not exceed 0.0015.

If replacing, firstly, remove the decorative frame/glass facia as described in section 8.4.The catalysts are located on

the top of the internal firebox and can be removed be unscrewing the retaining nuts securing the clamping plates.

Remove the catalysts their seals and discard. Refit the new catalysts and seals in reverse order, ensure the catalysts

and the glass door have good seals.

TESTING FOR FIREBOX LEAKAGE

Appliances that are several years old or have been extensively dismantled should be checked for soundness. It is

important that all the products of combustion pass through the catalytic converter at the top of the firebox

before leaving the appliance.

The firebox is heated by lighting for a few minutes to provide a flow through the firebox.The burner is then shut

off and a smoke pellet or match introduced at the base of the fire underneath the burner tray. Large quantities of

smoke will emerge from the top of the appliance, but none should emerge from the joints or gasket faces, espe-

cially around the door.

It is important to note that the appliance can never be expected to be 100% smoke tight and small quantities of

smoke may be seen in corners of joints and gasket faces etc without affecting safety when the fire is in operation.

CO (%)

CO2 (%) = ratio

10.4

10.3

TROUBLESHOOTING GUIDE

Fire sparks but pilot does not light No gas to fire, check isolators are open.

Pipe work blockage, clean out.

Air not fully purged, re purge supply or wait longer.

Spark earthing to metal work, reset gap correctly.

Blocked pilot, clean out internally.

Pilot lights but then goes out Severe restriction in gas supply: clear obstruction.

Faulty thermocouple, replace pilot unit.

Blocked pilot, clean out.

Blocked lint gauze, clean.

Hold control knob in for longer.

Check the spindle does not foul the casing.

If the pilot will not stay lit there is a problem with dirt,

the gas supply, or the thermocouple needs replacement.

Modifications are dangerous and can have a serious

unseen effect on safety. NEVER MODIFY OR BEND THE

THERMOCOUPLE TO MAKE THE PILOT STAY ALIGHT.

Fire does not spark at pilot HT lead detached, refit.

Check the spark gap (see section 8.2).

Faulty piezo unit, replace.

Debris shorting out electrode, clean.

Spark shorting to metalwork under tray, realign HT lead.

Fire runs for a time and then cuts off Loose or faulty thermocouple, rectify.

Blocked pilot, clean out.

Dirt or lint in pilot aeration hole or on the lint gauze,

clean thoroughly.

If the pilot will not stay lit there is a problem with dirt,

the gas supply, or the thermocouple needs replacement.

Modifications are dangerous and can have a serious

unseen effect on safety. NEVER MODIFY OR BEND THE

THERMOCOUPLE TO MAKE THE PILOT STAY ALIGHT.

Pilot flame shrinks when fire is on high Poor gas flow to fire, check pressure with fire on high.

If pressure is low, remove any restriction in pipework or

valve.

Check all isolators are adequately sized and fully open.

Check meter pressure is adequate.

If the pilot will not stay lit there is a problem with dirt,

the gas supply, or the thermocouple needs replacement.

Modifications are dangerous and can have a serious

unseen effect on safety. NEVER MODIFY OR BEND THE

THERMOCOUPLE TO MAKE THE PILOT STAY ALIGHT.

Fire smells when first lit or in use Newness smell from brand new appliance.

Leakage occurring. Carry out leakage test and rectify

any problems.

Combustible materials used in incorrect positions.

11.0

DO005905/0

As our policy is one of continuous improvement and development , we hope therefore you will understand we must retain the right to

USER INSTRUCTIONS

All instructions must be handed to the user for safekeeping.

Revision A - 05/07

Country(s) of destination - GB/IE

COMO

MODEL : L23

WALL MOUNTED FLUELESS GAS FIRE

Next Retail Ltd, Desford Road, Enderby, Leicester LE19 4AT

Helpline Telephone : 0844 844 8999

It is the LAW that all gas appliances and fittings are installed by a competent person (such as a CORGI registered fitter) and in

accordance with the Gas Safety (Installation and Use) Regulations 1998.

USER INSTRUCTIONS

Section Content Page No

1.0 Important Notes 1

2.0 Clearances to Combustibles 2

3.0 Ventilation & Room Size 2

4.0 Operating Instructions 3

5.0 Combustion Monitoring System 3

6.0 Cleaning 3

7.0 Servicing 3

8.0 List of Replacement Parts 3

IMPORTANT NOTES

The installation and Servicing of this fire MUST only be carried out by a competent person (such as a CORGI reg-

istered fitter) in accordance with the Gas Safety (Installation and Use) Regulations 1998, the relevant British

Standards, Codes of Practice, the Building Regulations and the manufacturer's instructions.

Failure to comply with the above recommendations could lead to prosecution and invalidate the appliance warranty.

Always keep a note of the installer's name and address, CORGI registration number, the original purchase receipt

and the date of installation for future reference. Failure to produce these documents may invalidate the warranty.

The appliance should be serviced regularly to ensure continued safe operation. See the servicing section for further

reference. Parts of this appliance become naturally hot during use. It is recommended that a suitable fireguard con-

forming to BS 8423 : 2002 is used, especially where young children, pets, the elderly or infirm are concerned.

The manufacturer of this appliance considers all surfaces as working surfaces with the exception of the control knob

and indicator bracket.

Combustible items, such as flooring and furniture and soft wall coverings (such as blown vinyl or embossed paper),

low temperature surrounds etc may discolour if fitted too close to the fire. See relevant section for further details

on clearances to combustibles. No combustible materials or flooring should protrude onto the hearth (if fitted).

This appliance incorporates a combustion monitoring system (ODS).

DO NOT burn any foreign material on this fire. Under no circumstances shall the appliance be used if the glass front

door or panel has been removed, damaged or is open. DO NOT place any objects on top of the appliance, or cover

the outlet grille in any way. DO NOT operate the appliance with any parts removed or missing.

The integral catalysts should be checked by the installer upon servicing to ensure there are no defects or obstruc-

tions that may prevent the satisfactory flow of combustion products.The expected life of the catalyst is in excess of

11,000 hours (10 years of normal use). After this time the catalyst should be replaced.

This appliance is only suitable for the gas type for which it is supplied.

It should be noted that heaters create warm air currents.These currents move heat to wall surfaces next to the

heater. Installing the heater next to vinyl or cloth wall coverings or operating the heater where impurities in the air

(such as tobacco smoke, candle smoke etc.) exist, may discolour walls.

WARNING: Due to the nature of this product the area around the top of the appliance (i.e. the grille) gets very hot.

Care should be taken when operating the appliance.

On first light up of a new appliance, initial curing of high temperature paint and burning off of lubricants may occur

for the first few hours of operation. During this period some smoke may be emitted from the outlet grille, this should

be no cause for concern. Accordingly, the room should be well ventilated with all windows and doors open during

this period. During this period the appliance may cause smoke alarms to sound. If this happens, reset the alarms, but

do not remove the batteries.

Except where otherwise stated, all rights, including copyright in the text, images and layout of this booklet is owned

by Focal Point Fires plc.You are not permitted to copy or adapt any of the content without the prior written per-

mission of Focal Point Fires plc.

1.0

CLEARANCES TO COMBUSTIBLES

Clearances to non-combustibles

Non combustible surfaces are defined as brick, metal, marble, concrete etc. and also a number of man-made mate-

rials impervious to flame. If in doubt refer to the material manufacturer for further information before proceeding

with installation.

Clearances to the sides of the appliance are 100mm (4”). Clearance to the front of the appliance is 500mm (20”).

The back of the appliance may be installed directly onto a non-combustible wall, providing the area behind the appli-

ance is flat and does not interfere with the various vent holes in the back panel of the appliance.

A non combustible shelf of any depth may be positioned above the appliance provided it is no closer than 400mm

from the top of the appliance glass panel and the wall above the appliance is non combustible.

The appliance must not be positioned vertically within 60mm ( 2.4”) of a solid floor (i.e. wood or stone) or hearth.

This dimension is measured vertically to the bottom of the appliance firebox.

Clearances to combustible materials

Combustible materials are defined as wood, fabrics, or other materials likely to combust if exposed to flame.

Generally, any material, which is likely to discolour, melt or misshape when exposed to moderate heat, should be

considered as a combustible material or surface.

Clearance to the sides of the appliance are 100mm (4”) but curtains, drapes and other fabrics are not permitted

within a distance of 500mm(20in) of the appliance sides. No such materials are permitted directly above the appli-

ance regardless of distance.

The minimum clearance to the ceiling above the appliance is 800mm (31.5”) measured from the top of the appliance

glass panel. Combustible materials should not be positioned directly in front of the appliance within a distance of

one metre.