Focusrite vocaster DM1 User manual

focusrite.com Tell the world 1
Introduction
The Vocaster DM1 is a dynamic microphone tuned for recording close-
proximity studio-quality voices. We’ve optimised the frequency response
for voice recording for podcasts, broadcasts, and streaming.
The Vocaster DM1 includes:
• A built-in grille and pop lter
• A microphone stand clip
• A cardioid polar pickup pattern.
The Vocaster DM1’s cardioid pickup pattern (See “Polar Pattern” on
page 3), its dynamic capsule, and built-in grille mean you can record
anywhere and capture studio-quality voice recordings.
While we recommend you mount your Vocaster DM1 on a stand using the
included microphone stand clip, it’s designed for rumble free recording so
you can use the microphone hand-held for on-the-go recording.
Dimensions
25mm
41mm
164mm
User Guide

focusrite.com Tell the world 2
Setup
Using DM1 with a microphone stand
The Vocaster DM1 includes a microphone stand clip and a microphone stand thread
adaptor (inside the microphone stand clip). Microphone stand mounts come in two
standard screw sizes. The Vocaster DM1 mic clip has a removable adaptor you can insert
or remove to t your microphone stand.
Removable
adaptor
Microphone
pickup direction
Vocaster DM1 FAQs
Does the Vocaster DM1 need 48V (Phantom Power)?
No, the Vocaster DM1 is a dynamic moving coil microphone. This type of microphone
doesn’t need power to work.
Will the Vocaster DM1 be damaged by 48V (Phantom power)?
No, the Vocaster DM1 will not be damaged if you send it 48V accidentally, or if you need
to enable 48V for all channels on your interface.
How far should I be from the microphone?
Speaking close to the microphone reduces the effect of the room’s acoustics, but
increases the bass response. This can be good for some voices but for a more natural
sound, move away from the microphone slightly, about the length of a st (10-15 cm).
If the room you’re using doesn’t sound good, the further you are from the microphone,
the more you’ll hear the room sound when you listen to the recording. Natural room
reverberation is neither good or bad, but often inappropriate for voice recordings.
The microphone is quiet or sounds strange?
Make sure you’re speaking into the end of the microphone (see diagram), if the
microphone is still too quiet, try increasing the gain on your interface, speaking louder, or
getting closer to the microphone.
Can I use an XLR to jack cable with my microphone?
The Vocaster DM1 is designed for use with an XLR cable. An XLR to jack cable might work
but it’s likely to sound worse or not work.

focusrite.com Tell the world 3
SpecificationsSpecifications
Technical Specications
Capsule
Type Dynamic (Moving Coil)
Polar Pattern Cardioid
Performance
Sensitivity
(0dB = 1V/Pa at 1kHz) -53dB ±3dB
Frequency Response 50Hz - 14kHz
Impedance (@1kHz) 19Ω ±20%
Physical Characteristics
Mounting Standard 5/8”; 3/8” adaptor supplied
Net Weight 405g (14.28 oz)
Body Dimensions Diameter
Length
41mm
164mm
Finish Matte Black/Red Trim
Output Connector 3-Pin XLR, balanced output
Pin 1 (Ground), Pin 2 (+), Pin 3 (-)
Frequency Response
A microphones frequency response chart shows how sensitive a microphone is across the
audible frequency range for human hearing. We’ve designed Vocaster DM1’s frequency
response for studio-quality voice recordings.
20
20 50 100 200 500 1K 2K 5K 10K
20K
10
0
-10
-20
-30
dB
Hz
Polar Pattern
The polar pattern shows how sensitive the microphone is in the areas around the
microphone. The angle 0° refers to speaking into the end of the Vocaster DM1.
8,000 Hz
1,000 Hz 5,000 Hz
0˚
30˚
60˚
90˚
120˚
150˚
180˚
210˚
240˚
270˚
300˚
330˚
-5
-10
-15
-25
dB

focusrite.com Tell the world
Accessories and Spare Parts
To get spares or support for your Vocaster DM1 please either contact our Spares &
Support teams, or speak to your local distributor:
Contact our Spares Team: support.focusrite.com
Contact your local distributor: stockists.focusrite.com
4