FOGE VL-FLD Series User manual

Instruction Manual
Product: VL-FLD Series Large
Area Flat Dome Light
FÖGE ELEKTRONIK GMBH
Böhleswasenweg 11
72555 Metzingen
www.fogegmbh.com
[e-mail]
[phone]
P1 Ver. 20.3.001

1. Intended Use
2. Technical Information
VL-FLD Series Large Area Flat Dome Light is designed for use in industrial
areas. Purpose of the product is inspection of parts, positioning, color check, code reading,
quality inspection, robot picking. Light is positioned above the part.
The system must be operated within the limits specified in technical data and used according
to technical specifications as well as installation instructions. The system must be used in
such a way that no person are in danger or machines and other material goods are
damaged in the event of malfunction or total failure of the system. Take additional precautions
for safety and damage prevention in case of safety related applications.
P2 Ver. 20.3.001
VL-FLD-300-300-W-24-C30 W 6500K 24VDC M8 4 pin w 300mm cable 300 300 352 385 26
VL-FLD-400-400-W-24-C30 W 6500K 24VDC M8 4 pin w 300mm cable 400 400 452 485 26
VL-FLD-500-500-W-24-C30 W 6500K 24VDC M8 4 pin w 300mm cable 500 500 552 585 26
VL-FLD-600-600-W-24-C30 W 6500K 24VDC M8 4 pin w 300mm cable 600 600 652 685 26
VL-FLD-700-700-W-24-C30 W 6500K 24VDC M8 4 pin w 300mm cable 700 700 752 785 26
VL-FLD-800-800-W-24-C30 W 6500K 24VDC M8 4 pin w 300mm cable 800 800 852 885 26
VL-FLD-900-900-W-24-C30 W 6500K 24VDC M8 4 pin w 300mm cable 900 900 952 985 26
VL-FLD-1000-1000-W-24-C30 W 6500K 24VDC M8 4 pin w 300mm cable 1000 1000 1052 1085 26
24W
34W
43W
50W
70W
80W
90W
100W
Model
Wavelength/
Color
Temperature
Power
Suppy Power Consumpon Connecon A(mm) B(mm) C(mm) D(mm) E(mm)
Colour

3. Dimensions / Installation
System operation assumes knowledge of the assembly instructions. The
symbols used for safety is shown in section 8(Safety) of manual.
P3 Ver. 20.3.001
Camera
VL-FLD
Part
Sample Applications
Wide area contaminaon
detecon
Color differenaon,
classificaon on big objects
Wide area posion detecon,
surface inspecon
Accessories
VL-FLD Series VL-BLA-BR-011
Suitable Product Ordering Code Accessories Image

Use high intensity modes only with trigger and strobe
type lighting. Do not use product continuous mode
with high intensity.
With dip swithes
located on the
product, you can
increase the
light intensity
when it is
needed.
P4 Ver. 20.3.001
4.Electrical Connection
5. Display/Controls
Can be used without strobe, connuous
illuminaon mode
Due to high illuminaon sengs, use
this mode only with strobe input with given
ON/OFF percentage.
Due to high illuminaon sengs, use
this mode only with strobe input with given
ON/OFF percentage.
Due to high illuminaon sengs, use
this mode only with strobe input with given
ON/OFF percentage.
Due to high illuminaon sengs, use
this mode only with strobe input with given
ON/OFF percentage.
ON : % 100
OFF : % 0 (Standard High Intensity)
ON : % 85
OFF : % 15
ON : % 72
OFF : % 28
ON : % 60
OFF : % 40
ON : % 50
OFF : % 50 (Ultra high light Intensity)
Light ON Posion Percentage Light
Intensity Accessories Image
Illuminaon
intensity
modes with
dip switches

6. Faults
In any case do not open the product.
If the leds not on check the connection and power supply.
If still leds are not on contact FÖGE or distributor.
7. Warnings
Connect the power supply and the display/output device according to the safety
regulations for electrical equipment.
The supply voltage must not exceed the specified limits.
Avoid shocks and impacts to the sensor.
Protect the cable against damage.
•
•
•
•
Possible Results of Avoidance
Risk of injury by electric shock
Damage to or destruction of the sensor
P5 Ver. 20.3.001

8. Safety
System operation assumes knowledge of the assembly instructions. The
following symbols are used in these assembly instructions:
9.Liability for Material Defects
All components of the device have been checked and tested for functionality at the production
facility. However, if defects occur despite our careful quality control, FÖGE or your dealer must be
notified immediately.
The liability for material defects is 12 months from delivery.
Within this period, defective parts, except for wearing parts, will be repaired or replaced free of
charge, if the device is returned to FÖGE with shipping costs prepaid. Any damage that is caused by
improper handling, the use of force or by repairs or modifications by third parties is not covered by
the liability for material defects. Repairs are carried out exclusively by FÖGE.
Further claims can not be made. Claims arising from the purchase contract remain unaffected. In
particular, FÖGE shall not be liable for any consequential, special, indirect or incidental damage. In
the interest of further development, FÖGE reserves the right to make design changes without
notification.
10. Decommissioning, Disposal
Remove the power supply and output cable on the sensor.
Incorrect disposal may cause harm to the environment.
Dispose of the device, its components and accessories, as well as the packaging materials in
compliance with the applicable country-specific waste treatment and disposal regulations of the
region of use.
Indicates a hazardous situation which, if not avoided, may result
in minor or moderate injury.
Indicates a situation that may result in property damage if not
avoided.
Indicates an electrical shock if not avoided or properly follow
comments.
P6 Ver. 20.3.001