FONESTAR DA-864 User manual

DA-864
UHF ANTENNA SPLITTER
INSTRUCTION MANUAL

We take this opportunity to thank you for buying this product.
We recommend you read the instruction manual before switching on the machine and follow the instructions
that are given. eep the manual for future reference.
ECURITY AND THE ENVIRONMENT
ELECTRICAL SECURITY
Check that the current in the mains connection where the machine is to be installed corresponds to the
power supply of the machine.
To avoid damaging the equipment, electrical shocks, fire or physical injury when you connect or disconnect
the equipment from the power supply, pull the plug firmly out of the mains socket holding the plug, never the
cable.
Always do this with dry hands.
eep the power supply cable far from sources of heat. Do not put heavy objects on top of it or change it.
Clean dust and dirt off the power supply cable regularly.
Do not open the machine; you could get an electric shock.
CAUTION
While installing the machine, make sure it is switched off and unplugged.
Do not open the machine. Touching the internal parts is dangerous and you could receive an electric shock.
The machine must not be splashed or dripped on. Never place recipients with liquid inside on the machine.
Do not place anything inside the machine.
LOCATION
Place the equipment on a horizontal surface with enough space around it to allow ventilation.
Avoid direct sunlight, heat sources and excessive dust.
Do not place the machine near magnetic fields or static electricity.
Do not use surfaces which vibrate or receive impact.
Do not pile machines on top of one another.
VENTILATION
Never block or cover the ventilation slits on the machine.
Do not expose it to direct sunlight or place it near sources of heat.
PERIODS OF INACTIVITY
When the machine is not going to be used for a long period of time, disconnect it from the mains.
If you are using an adapter, take into account that it will continue using electricity even if the machine is
switched off. If it is not going to be used for a long period of time, disconnect it from the mains.
THE ENVIRONMENT
To save energy, switch the machine off when you are not going to use it for a long time. The machine could
contain substances that are harmful to the environment or human health. To minimize the effect of these
substances the machine must be correctly managed and recycled when you decide to dispose of it.
When you dispose of it remember: it cannot be thrown into a conventional rubbish bin.
If it contains or uses batteries, these must be disposed of separately.
The machine (without batteries) must be disposed of correctly. Put it in a container specially intended for the
collection of electronic and electrical appliances, at the dump or hand it over to the dealer when you purchase
similar equipment, so that the dealer can dispose of it correctly (at no added cost).
- 2-
EN

IGNIFICANCE OF THE YMBOL ON THE MACHINE*
The symbol formed by the expression “Class 1 laser product” written in a rectangle
indicates that visible or invisible laser radiation could be produced. Avoid direct exposure
to the laser.
The symbol formed by a ray of lightening inside a triangle shows that the machine has
connection terminals or a circuit with areas with a current which could cause an electric
shock, even in normal working conditions.
The symbol formed by an exclamation mark in a triangle shows that the instruction manual
must be referred to for information on how the machine works and its use.
The symbol formed by one square inside another square shows that the machine has
double electrical insulation.
The European Community symbol shows that the machine complies with the current
European Union legislation, as well as its transposition to local legislation.
The symbol of a rubbish bin crossed out and over a horizontal line shows that when the
product is disposed of it must be done properly, placing it in a special selective electronic
and electrical equipment container or through a dealer when purchasing a similar product,
at no additional cost. It also shows that the machine was put on the market after 13th
August 2005 (European Community Directive 2002/96/CE of Electrical and Electronic
recycling, and its Spanish equivalent R.D.208/2005).
In accordance with what is set out in the aforementioned decree, FONESTAR is registered
in the RAEE (Registro de Aparatos Eléctricos y Electrónicos) in a special section REI
(Registro de establecimientos Industriales), with the entry number 001851.
*It is possible that some of these symbols do not appear on the machine.
EXEMPTION OF LIABILITY
The characteristics of the equipment and the content of the manual can change without forewarning.
FONE TAR, .A. does not assume responsibilities regarding the inappropriate use of the equipment or the
information supplied in this instruction manual, and specifically disclaims any implied liability for marketability
or fitness for any other use.
All rights reserved by FONE TAR, .A.
- 3-
EN

DE CRIPTION
- Antenna splitter for 4 UHF wireless system receivers.
-It improves the antenna signal reception if the receivers are in racks.
-It uses 2 front antennas to distribute the antenna signal to 4 receivers.
CONTROL AND FUNCTION
FRONT PANEL
1.- ANTENNA A/ANTENNA B: LED signal status and A and B input signal amplification indicators.
-BOO TER: indicates 8 V signal presence in the output of antennas A or B.
-CALIBRATE FAIL: indicates that it is necessary to calibrate the connected amplifier or that it is
not possible to calibrate it due to losses produced in the cable.
-CALIBRATE PA : indicates the correct calibration of the amplifiers connected in the antenna
output A or B.
2.- CALIBRATE: this button is used to automatically calibrate the gain of the amplifiers connected in the
antenna output A and B to compensate for the losses produced by the wiring.
3.- POWER: splitter on/off switch.
4.- Holes for installation of antennas A and B.
REAR PANEL
1.- ANT B IN: antenna B microphone signal input, TNC connector.
2.- RF OUT B: microphone signal output for its distribution to the microphone receivers, TNC connector.
3.- 12 V, 450 mA power supply.
4.- RF OUT A: microphone signal output for its distribution to the microphone receivers, TNC connector.
5.- ANT A IN: antenna A microphone signal input, TNC connector.
- 4-
EN

CONNECTION EXAMPLE
- Connect the antennas to the ANT A IN and ANT B IN inputs directly or if the antennas are installed on the
front, use the antenna cables with male TNC connectors that are provided. For long lengths of cable use
an antenna signal amplifier.
For this amplification, several options are available:
- Connecting the amplifier mod. AMP-818G together with an antenna mod. ADU-830. The amplifier can
be powered using the antenna splitter via the ANT IN input connector or, preferably, using a mains
adapter (must be used for lengths of cables greater than 10 meters).
- Connecting the UHF directional antenna directly with an integrated amplification circuit mod.
ADU-823AMP. This antenna is powered via the antenna cable itself with an 8 V signal provided by the
DA-864 splitter.
- Finally, connect all the devices in the installation to the mains supply.
1. SIMPLE CONNECTION
- 5-
EN

EN
- 6-
2. CONNECTION WITH AMPLIFIER AMP-818G
- In distances below 100 meters the AMP-818G amplifier is powered through the antenna splitter itself.
- In distances over 100 meters the AMP-818G amplifier must be powered by a mains adapter.

EN
- 7-
3. CONNECTION WITH AMPLIFIED ANTENNA ADU-823AMP
Note: the antenna ADU-823AMP has an amplifier circuit that must be powered via the antenna connection.
TECHNICAL PECIFICATION
DA-864
FREQUENCY UHF 500-960 MHz
GAIN 13 dB ±0.5 dB
INPUT 2 antenna, female TNC 50 Ω
Power supply for antenna amplifier mod. AMP-818G, 8 V DC
OUTPUT 8 antenna for 4 receivers, female TNC 50 Ω
POWER UPPLY 12 V DC, 1 A, with adapter included
DIMEN ION 483 x 45 x 210 mm depth. 1 U 19" rack
ACCE ORIE Mounts for antenna installation on the front with female TNC - female TNC
connectors
10 x 0.5 m cables, male TNC - male TNC, to connect the antenna to the
splitter and the device outputs
OPTIONAL AMP-818G: antenna amplifier
COMPATIBILITY For wireless FONE TAR systems, mods. M HR-45 and M HR-46D

DECLARATION OF CONFORMITY
FONE TAR I TEMA , .A.
Polígono trascueto, s/n
39600 Revilla de Camargo, Cantabria (Spain)
This declaration of conformity is issued under the sole responsibility of the manufacturer.
Description: UHF antenna splitter
Brand: FONESTAR
Models: DA-864
is in conformity with the relevant Union harmonisation legislation: Directive 2014/53/UE.
Harmonised standards in relation to which conformity is declared.
EN 60065:2014
EN 301 489-1 V2.2.0
EN 301 489 V1.1.0
EN 303 340 V1.1.2
Santander, 1st February 2018
Juan Vallejo
Technical Engineer, Sales Department
WARRANTY
This product has been tested and has passed the corresponding quality control prior to being put on the market.
FONE TAR guarantees the suitability of the product for its specified use during a period of 2 years from the
delivery date and commits itself to repair or substitute the goods as expressed in the Spanish law ‘La Ley General
para la Defensa de los Consumidores y Usuarios, Real Decreto Legislativo 1/2007 16 Noviembre.
The lack of conformity in the first six months after purchase, due to a manufacturing defect, will be rectified with
no more than showing the proof of purchase. After six months FONE TAR reserves the right to demand proof of
the product being sold with that problem.
This warranty does not include damage produced by: inappropriate use or negligence, accidents, worn out parts
due to use, breakages, burns, spilt liquids or other substances, excessive humidity, battery deterioration and
internal manipulation of the device, the software or its components by unauthorized persons, and in general any
use that is unrelated to the nature and purpose of the product.
If any service is needed during the warranty period because of lack of conformity, please contact the business or
distributor where the product was purchased in no more than 2 months after being conscious of the problem. It
is only necessary to contact FONE TAR if it is impossible or imposes an undue burden for them to solve it.
To benefit from this warranty it is necessary to show the proof of purchase with the date clearly visible, with no
corrections or crossing out.
This document adds information, and never decreases the consumers’ rights, which in all cases are protected by
the Spanish law ‘La Ley General para la Defensa de los Consumidores y Usuarios, Real Decreto Legislativo 1/2007
16 Noviembre.
FONE TAR is a member of ECOEMBALAJES ESPAÑA, S.A. “ECOEMBES”, with number 03497 and all our products carry
the symbol, backed by our membership and subscription to the above mentioned organization with the recycling and
subsequent management of our packaging.
FONESTAR, S.A. - NIF: A28780443 - Polígono Trascueto - 39600 Revilla de Camargo, Cantabria (Spain)
www.fonestar.com