Fortec Star Advantech MIO-5152 User manual

The information contained in this document has been carefully researched and is, to the best of our
knowledge, accurate. However, we assume no liability for any product failures or damages, immediate or
consequential, resulting from the use of the information provided herein. Our products are not intended for
use in systems in which failures of product could result in personal injury. All trademarks mentioned herein
are property of their respective owners. All specifications are subject to change without notice.
Manual
Advantech
MIO-5152
3,5” Single-Board Computer with Elkhart Lake Intel® Atom® x6000E series and Celeron® N and J series
processor

User Manual
MIO-5152
Intel® Atom™ x6000E series and
Intel® Celeron® N and J series 3.5"
SBC

MIO-5152 User Manual ii
Copyright
The documentation and the software included with this product are copyrighted 2021
by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right
to make improvements in the products described in this manual at any time without
notice. No part of this manual may be reproduced, copied, translated, or transmitted
in any form or by any means without the prior written permission of Advantech Co.,
Ltd. The information provided in this manual is intended to be accurate and reliable.
However, Advantech Co., Ltd. assumes no responsibility for its use, nor for any
infringements of the rights of third parties that may result from its use.
Acknowledgments
Intel® is a trademark of Intel® Corporation.
AMI is a trademark of American Megatrends, Inc.
IBM, PC, PS/2, and VGA are trademarks of International Business Machines Corpo-
ration.
Microsoft Windows®, DirectX® is a registered trademark of Microsoft Corp.
All other product names or trademarks are properties of their respective owners.
For more information on this and other Advantech products, please visit our websites
at:
http://www.advantech.com
http://www.advantech.com/eplatform
For technical support and service, please visit our support website at:
http://support.advantech.com/
This manual is for the MIO-5152.
Part No. 2006515200 Edition 1
Published in Taiwan September 2021

iii MIO-5152 User Manual
Product Warranty (2 years)
Advantech warrants the original purchaser that each of its products will be free from
defects in materials and workmanship for two years from the date of purchase.
This warranty does not apply to any products that have been repaired or altered by
persons other than repair personnel authorized by Advantech, or products that have
been subject to misuse, abuse, accident, or improper installation. Advantech
assumes no liability under the terms of this warranty as a consequence of such
events.
Because of Advantech’s high quality-control standards and rigorous testing, most
customers never need to use our repair service. If an Advantech product is defective,
it will be repaired or replaced free of charge during the warranty period. For out-of-
warranty repairs, customers will be billed according to the cost of replacement mate-
rials, service time, and freight. Please consult your dealer for more details.
If you believe your product to be defective, follow the steps outlined below.
1. Collect all the information about the problem encountered. (For example, CPU
speed, Advantech products used, other hardware and software used, etc.) Note
anything abnormal and list any onscreen messages displayed when the prob-
lem occurs.
2. Call your dealer and describe the problem. Please have your manual, product,
and any helpful information readily available.
3. If your product is diagnosed as defective, obtain a return merchandise authori-
zation (RMA) number from your dealer. This allows us to process your return
more quickly.
4. Carefully pack the defective product, a completed Repair and Replacement
Order Card, and a proof of purchase date (such as a photocopy of your sales
receipt) into a shippable container. Products returned without a proof of pur-
chase date are not eligible for warranty service.
5. Write the RMA number clearly on the outside of the package and ship the pack-
age prepaid to your dealer.

MIO-5152 User Manual iv
Declaration of Conformity
CE
This product has passed the CE test for environmental specifications when shielded
cables are used for external wiring. We recommend the use of shielded cables. This
type of cable is available from Advantech. Please contact your local supplier for
ordering information.
Test conditions for passing also include the equipment being operated within an
industrial enclosure. In order to protect the product from damage caused by electro-
static discharge (ESD) and EMI leakage, we strongly recommend the use of CE-
compliant industrial enclosure products.
FCC Class B
This equipment has been tested and found to comply with the limits for a Class B dig-
ital device, pursuant to part 15 of the FCC Rules. These limits are designed to pro-
vide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. However, there is no guarantee that interfer-
ence will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for assistance.
Technical Support and Assistance
1. Visit the Advantech website at www.advantech.com/support to obtain the latest
product information.
2. Contact your distributor, sales representative, or Advantech's customer service
center for technical support if you need additional assistance. Please have the
following information ready before calling:
–Product name and serial number
–Description of your peripheral attachments
–Description of your software (operating system, version, application software,
etc.)
–A complete description of the problem
–The exact wording of any error messages
Caution! There is a danger of a new battery exploding if it is incorrectly installed.
Do not attempt to recharge, force open, or heat the battery. Replace the
battery only with the same or equivalent type recommended by the man-
ual. Discard used batteries according to the manufacturer's instructions.

v MIO-5152 User Manual
Packing List
Before you begin installing your card, please make sure that the following materials
have been shipped:
If any of these items are missing or damaged, contact your distributor or sales repre-
sentative immediately.
1 x MIO-5152 SBC
1 x SATA cable 30 cm (11.8 in) (p/n: 1700006291)
1 x SATA power cable 35 cm (13.77 in) (p/n: 1700031583-01)
1 x USB 2.0 cable 20 cm (7.87 in) (p/n: 1700030406-01)
1 x Audio cable 20 cm (7.87 in) (p/n: 1700019584-01)
6 x COM RS-232/422/485 cable 20 cm (7.87 in) (p/n: 1700030404-01)
1 x Heatsink for x6000E (p/n: 1970005053T001)
1 x Heatsink for Celeron series (p/n: 1970005053T011)
1 x Startup manual (p/n: 2046515200)
1 x DeviceOn package

MIO-5152 User Manual vi

vii MIO-5152 User Manual
Contents
Chapter 1 General Information ............................1
1.1 Introduction ............................................................................................... 2
1.2 Specifications ............................................................................................ 2
1.3 Block Diagram........................................................................................... 4
Chapter 2 Mechanical ...........................................5
2.1 Introduction ............................................................................................... 6
2.2 Board Layout: Dimensions ........................................................................ 6
Figure 2.1 MIO-5152 Mechanical Diagram (Top Side) ................ 6
Figure 2.2 MIO-5152 Mechanical Diagram (Bottom Side)........... 6
Figure 2.3 MIO-5152 Mechanical Diagram (Coastline) ............... 7
Figure 2.4 MIO-5152 Mechanical Diagram with Heatsink (Top
Side) ........................................................................... 7
Figure 2.5 MIO-5152 Mechanical Diagram with Heatsink (Bottom
Side) ........................................................................... 8
Figure 2.6 MIO-5152 Mechanical Diagram with Heatsink (Coast-
line)............................................................................. 8
2.3 Quick Installation Guide ............................................................................ 9
2.3.1 Heatsink ........................................................................................ 9
Chapter 3 Installation..........................................11
3.1 Jumpers & Switches................................................................................ 12
Table 3.1: Jumpers and Switches ............................................. 12
3.2 Connectors.............................................................................................. 12
Table 3.2: Connectors ............................................................... 12
3.3 Locating Connectors ............................................................................... 13
Figure 3.1 MIO-5152 Connector Locations (Top Side).............. 13
Figure 3.2 MIO-5152 Connector Locations (Bottom Side)......... 13
3.4 Setting Jumpers ...................................................................................... 14
3.4.1 CMOS Clear Switch (JCMOS1) .................................................. 14
3.4.2 Panel Voltage Selection (VDD1)................................................. 15
3.4.3 COM RI# pin 5V/12V Selection (RI_VDD1) ................................ 15
3.4.4 ATX/AT Mode Selection.............................................................. 16
3.4.5 DC Input Connector .................................................................... 16
3.4.6 DC Input Connector (Adapter) .................................................... 17
3.4.7 Internal USB Connector .............................................................. 17
3.4.8 COM Port Connector (RS232+RS422+RS485).......................... 18
3.4.9 COM port Connector (RS232+RS422+RS485) .......................... 19
3.4.10 COM Port Connector (RS232) .................................................... 20
3.4.11 COM Port Connector (RS232) .................................................... 21
3.4.12 COM Port Connector (RS232) .................................................... 22
3.4.13 COM Port Connector (RS232) .................................................... 23
3.4.14 Audio Connector ......................................................................... 24
3.4.15 LVDS Connector......................................................................... 24
3.4.16 SMB Connector........................................................................... 26
3.4.17 FAN Connector ........................................................................... 26
3.4.18 HDD Power Connector ............................................................... 27
3.4.19 Panel Inverter Connector............................................................ 27
3.4.20 GPIO Connector ......................................................................... 28
3.4.21 Power/LED/Case Open/Buzzer Connector................................. 29
3.4.22 Key B Connector......................................................................... 30

MIO-5152 User Manual viii
3.4.23 Key E Connector......................................................................... 32
3.4.24 Key M Connector........................................................................ 34
3.4.25 RTC Battery Connector .............................................................. 36
Chapter 4 AMI BIOS Setup................................. 37
4.1 Entering Setup ........................................................................................ 39
4.1.1 Main Setup.................................................................................. 39
4.1.2 Advanced BIOS Features Setup................................................. 40
4.1.3 Chipset Configuration ................................................................. 64
4.1.4 Security....................................................................................... 76
4.1.5 Boot ............................................................................................ 77
4.1.6 Save & Exit ................................................................................. 78
Appendix A System Assignments........................ 79
A.1 System I/O Ports..................................................................................... 80
Table A.1: System I/O Ports ...................................................... 80
A.2 DMA Channel Assignments .................................................................... 81
Table A.2: DMA Channel Assignments ..................................... 81
A.3 1st MB Memory Map............................................................................... 81
Table A.3: 1st MB Memory Map ................................................ 81
A.4 Interrupt Assignments ............................................................................. 81
Table A.4: Interrupt Assignments .............................................. 81

Chapter 1
1General Information
This chapter details background
information on the MIO-5152.
Sections include:
Introduction
Specifications
Block diagram

MIO-5152 User Manual 2
1.1 Introduction
Advantech MIO-5152 is a 3.5” form factor SBC (compact series, 146 x 102 mm; 5.7 x
4.01 in). Powered by Intel® Atom® x6000E series and Intel® Celeron® N and J
series processors, it provides embedded iManager 3.0, SUSI 4.0, and Advantech’s
WISE-DeviceOn to monitor and control system operation effectively and remotely.
MIO-5152 supports single channel DDR4-3200 up to 32GB, 3 x independent displays
via LVDS, DP1.4, HDMI 1.4 up to 4K@30Hz, Dual GbE, 6 x USB, 6 x UART, and
TPM2.0.
1.2 Specifications
Platform
Processor Celeron J6412 Celeron N6210 Atom® x6425E
Max. Frequency 2.60 GHz 2.60 GHz 3.00 GHz
Base Frequency 2.00 GHz 1.20 GHz 2.00 GHz
Core/Tread 4/4 2/2 4/4
LLC L2 L2 L2
CPU TDP 10W 6.5W 12W
Chipset Intel Series Chipset (SoC Integrated)
BIOS AMI EFI 256Mbit
Memory
Technology DDR4-3200
Max. Capacity 32GB
Channel/Socket Single Channel / 1x Socket
ECC Support No No Yes
Graphics
Controller Intel Gen11 Graphics Engines (SoC integrated)
Max. Frequency 800MHz 750MHz 750MHz
Graphics Memory 400MHz 250MHz 500MHz
3D/HW Accelera-
tion
DX12, OGL4.5, OCL1.2, Vulkan 1.1, MPEG2, H.264,
JPEG/MJPEG, H.265 (HEVC)
Display I/F
LCD 1 x LVDS: Dual Channel 18/24-bit, up to 1920 x 1200
HDMI/DP 1 x HDMI 1.4, up to 4096 x 2160 x 24bpp@30Hz
1 x DP1.4a, up to 4096 x 2160 x 36bpp@60Hz
Multiple Display 3 x simultaneous displays with LVDS, HDMI, DP
Ethernet Controller LAN1: Realtek RTL8111H, LAN2: Realtek RTL8111H
Speed 10/100/1000 Mbps
External I/O
Ethernet 2 x RJ-45
HDMI/DP 1/1
USB 3.2 4 x TypeA; 4 x USB 3.2 Gen2 (10Gbps)
Power DC-Jack Optional

3 MIO-5152 User Manual
Chapter 1 General Information
Internal I/O
SATA 1 x SATA GenIII 6.0Gbps
USB 2.0 2 x
Serial Bus I2C (support 400Kbit/s)
COM Port 2 x RS-232/422/485 (support 1Mbps), 4 x RS-232
(115.2kbps)
GPIO 8-bit general purpose input output I/O
Audio Realtek ALC888s, Line-in/Line-out/MIC
Inverter 12V/5V
SPI Bus eSPI
Fan 4-wire smart fan
Front Panel Con-
trol Power-on, Reset, Buzzer, SATA LED, CaseOpen
Board
Feature
Watchdog Timer Programmable 1 ~ 255 sec/min
TPM TPM2.0, NPCT750AABYX
iManager 3.0 SW API for Hardware Monitor, Smart Fan Control, Bright-
ness Control, I2C, GPIO, WDT
Expansion M.2 E-Key/ B-Key 1 x E-Key 2230 (PCIe x1, USB 2.0)
Optional 1 x B-Key 3042 (PCIe, USB 2.0) w/ Nano-SIM
M.2 M-Key 1 x M-Key 2242 (SATA x1)
Power
Supply Voltage Vin: DC 12V +/- 10%; RTC Battery: Lithium 3V/210mAH
Connector ATX 2x2pin 90D, optional DC-Jack
Power Manage-
ment AT, ATX
Max. Consumption 21.39 W
Idle Consumption 7.31 W
Environment
Temperature Operating: Standard: 0 ~ 60 °C (32 ~ 140 °F)
Humidity Operating: 40 °C(104 °F) @ 95% relative humidity, non-
condensing
Vibration Resis-
tance 3.5 Grms
Software OS Windows10, Linux 20.04
Software & API WISE-DeviceOn and iManager 3.0
Certification EMC CE, FCC Class B
Mechanical Dimensions 146 x 102 mm (5.7 x 4 in)
Note! Support by request

MIO-5152 User Manual 4
1.3 Block Diagram
Intel
Elkhart Lake
(10+14nm)
Super I/O
NCT6126D
Internal I/O
PCIe
External I/O
Opt. Func.
PCIe
SATA
SATA
PCIe
USB2.0
PCIe
USB2.0
SPI
SPI
GbE #1 RJ-45
GbE #2 RJ-45
SATA
M.2 M-Key 2242
M.2 E-Key 2230
M.2 B-Key 3042 (Opt.)
TPM2.0
BIOS
I2C (opt. SMBus)
USB2.0 x 2
USB2.0 1x2
GPIO 8-bit
HWM, WDT, Fan
DP1.4
2 x RS-232/422/485
4 x RS-232
RS-232/422/485
RS-232
RTL8111H
RTL8111H
HDA
Line-in/out/MIC ALC 888
USB 3.2 1x2
USB3.1/2.0
USB 3.2 1x2
eDP
LVDS Dual Channel PTN3460
DDR4-3200 IBECC, 1-CH, 8/16/32GB
SO-DIMM Up to 32GB
HDMI 1.4 Diodes
PI3HDX1204B1ZHIEX

Chapter 2
2Mechanical
This chapter details mechanical
information on the MIO-5152.
Sections include:
Mechanical Diagrams
Assembly Diagrams

MIO-5152 User Manual 6
2.1 Introduction
The MI/O compact form factor SBC is a new-generation SBC designed- with a variety
of mechanical improvements. Here is the quick installation guide for the thermal
design and MIOe module. This chapter includes board dimension and assembly
instructions for the standard thermal solution.
2.2 Board Layout: Dimensions
Figure 2.1 MIO-5152 Mechanical Diagram (Top Side)
Figure 2.2 MIO-5152 Mechanical Diagram (Bottom Side)
   








      










7 MIO-5152 User Manual
Chapter 2 Mechanical
Figure 2.3 MIO-5152 Mechanical Diagram (Coastline)
Figure 2.4 MIO-5152 Mechanical Diagram with Heatsink (Top Side)
        









    

MIO-5152 User Manual 8
Figure 2.5 MIO-5152 Mechanical Diagram with Heatsink (Bottom Side)
Figure 2.6 MIO-5152 Mechanical Diagram with Heatsink (Coastline)
      













          

9 MIO-5152 User Manual
Chapter 2 Mechanical
2.3 Quick Installation Guide
There is a Heatsink in the white box inside the package. Please assemble it by fol-
lowing the diagrams below. Remember to remove the plastic on the thermal pad
before you assemble the mechanical parts.
2.3.1 Heatsink
5HPRYHUHOHDVHSDSHU

MIO-5152 User Manual 10