Fortress Technologies FSF1616 User manual

Stand Fan
User Manual
Model No.: FSF1616
*Before operating the appliance, please read this
manual and all the safety instructions thoroughly
and retain it for future reference.

CONTENT
PAGE
SAFETY INSTRUCTION
2
PARTS DESCRIPTION
3
INSTALLATION INSTRUCTION
4
OPERATION INSTRUCTION
7
MAINTENANCE INSTRUCTION
8
SPECIFICATION
8
WARRANTY
8

SAFETY INSTRUCTION
IMPORTANT SAFETY INSTRUCTIONS –READ CAREFULLY AND KEEP FOR FUTURE REFERENCE.
1. To avoid electric shock, fire or injury, please read the user manual carefully before using
the appliance and keep it for future reference.
2. This appliance is for household use only. Please use suitable power source (Please refer to
SPECIFICATION).
3. Never immerse the appliance in water or other liquids.
4. Do not use the appliance under direct sunshine.
5. Please turn off the appliance when not in use otherwise it may result in danger.
6. Please turn off the appliance and unplug the socket when unattended otherwise it may
result in danger.
7. Keep the appliance away from children.
8. The appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the appliance by a person responsible
for their safety.
9. Children should be supervised to ensure that they do not play with the appliance.
10. With any indication of damage or malfunction, please stop using the appliance
immediately to avoid hazards. Take it to the authorized service center for repair. Do not
attempt to repair or change any parts by yourself.
11. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or
similarly qualified persons in order to avoid hazards.
12. Please turn off and unplug the appliance before cleaning or maintenance.
13. Clean the surface of the appliance with a dry cloth. Do not use corrosive detergent or
solvent to clean. Do not swash the appliance with water.
14. Please turn off and unplug the appliance when not in use. Make sure the power is off
before pulling out the plug and do not pull the cord.
15. When the appliance is not in use for a prolonged period, please turn it off, unplug it, pack it
well, and store it in dry cool place.
16. Forbid to put flammable and explosive objects around the appliance, and do not use the
appliance in an environment full of flammable gas and powder. Keep away from any fire
and heat sources.
17. Please put the power cord in the right place in order to avoid tripping the appliance over.
18. Please keep the air inlet and the air outlet unblocked to minimize the risk of fire or
malfunction.
19. Ensure no water or raindrop leaks into the appliance in order to avoid electric shock. Do
not put flammable objects or wet clothes on the air outlet in order to avoid short circuit or
fire.
20. Please do not place the air inlet or the air outlet near to curtains or walls when operation
because it will block the air current and cause fire. The appliance should be installed at
minimum distant of 10 cm from the wall or other obstacles.
21. Please do not insert any objects into the air inlet or the air outlet in order to avoid electric
shock.
22. After a period of operation, abnormal noise and uneven air volume may appeared because
of dust blocking airflow. It will disappear after cleaning the air inlet and outlet.
23. Do not insert any objects in the fan to prevent any injury or damage.
24. Do not hang any objects on the louver to prevent destabilizing the fan and impairing its
operation.
- 2 -

PARTS DESCRIPTION
Guard ring
Front guard
Rear guard
Motor
Fan blade
Head unit
Power cord
Height adjustment
Inner pole
Height adjustment ring
Height adjustment outer pole
Base plate
- 3-

Screw
Screw
Screw hole
INSTALLATION INSTRUCTION
Caution: Please unplug the appliance before installation.
1. Base and head unit installation
Loosen the height adjustment ring in anticlockwise direction. Lift the inner pole to certain
height and screw the height adjustment ring in clockwise direction. Rotate out the
connecting sheet and connecting bar at the bottom of the outer pole (Fig. 1).
Fit the outer pole into the center section of the base late (Fig. 2).
Connect the outer pole, the base plate and the connecting sheet together with the
connecting bar (Fig. 3).
Loosen the screw on the bottom of the head unit but do not unscrew it totally (Fig. 4).
Place the head unit into the inner pole and tighten the screw (Fig. 5).
Fig. 1
Fig. 2 Fig. 3
Insert
Fig. 4
-4 -
Fig. 5
Height
adjustment
ring
Connecting
sheet
Connecting
bar
Twist in
anticlockwise
direction to
loosen it

Motor shaft
Rear grille knob
Rear grille knob
Fan blade groove
2. Guard and fan blades installation
A. Rear guard
Unscrew the fan blade knob from the motor shaft in clockwise direction (Fig. 6).
Unscrew the rear grille knob from the motor shaft in anticlockwise direction (Fig.6).
Set the rear guard and fit it well on the two position holes and make sure these holes are
properly put through the holes on the rear guard (Fig. 7).
Hold the rear guard and screw the rear grille knob into the motor front cover in a
clockwise direction (Fig.8).
Fig. 6 Fig. 7 Fig. 8
B. Fan blade
Install the fan blade through the fan blade position hole. Ensure the fan blade grooves fit
the motor shaft fixing pin and push it until it reaches the fixing pin (Fig. 9).
Install the fan blade in anticlockwise direction onto the motor shaft until it's tightened.
Please hold the fan blade when installing the fan blade knob (Fig. 10).
Fig. 9
-5 -
Fan blade
knob
Position
holes
Motor shaft
fixing pin
Motor shaft

Blade knob
Fig. 10
C. Front guard
Normally, the guard ring is installed with the front guard. Loosen the screw on the bottom
of the guard and fit the front guard with guard ring into the rear guard. After that, lock the
guard clip and tighten the screw (Fig.11).
Outer ring of
rear guard
Limit groove of
guard ring
Guard ring
Guard clip
Fig. 11
-6 -
Screw

OPERATION INSTRUCTION
1. Power on / speed adjustment
Press fan speed button for speed adjustment：
0:Off / Stop 1:Soft Speed 2:Low Speed
3:Medium Speed 4：High Speed
Note: If the timer knob is turned to “OFF”, the fan is turned off. Please ensure the timer
knob is turned to “ON” or selected time before starting the operation.
2. Timer
Turn the timer knob to “ON”, the fan will be operated continuously, no auto off timer
setting.
Turn the timer knob to the number, which indicates the fan will stop after the set time
limit.For example, turning to 20 means the fan will be off after 20 minutes; Turn the timer
knob to “OFF”, the fan will not operate.
3. Oscillation
Press the oscillation switch, the fan will operate in oscillating mode to swing horizontally.
Press the oscillation switch again to stop the oscillation.
4. Height adjustment
Turn off the fan, then hold the height adjustment pole and
loosen the height adjustment ring in anticlockwise direction,
then adjust the pole to the required height and tighten the
height adjustment ring by twisting it in clockwise direction.
5. Angle adjustment
Turn off the fan, then lift or press the motor lightly to
adjust the blowing angle.
-7 -
Twist in clockwise
direction to tighten it

Model No.
FSF1616
Product name
Stand fan
Rated Voltage/Frequency
220V-240V~ 50Hz
Rated Power
65W
Dimension (W x H x D)
445 x1380x420mm
MAINTENANCE INSTRUCTION
Attention:
·Please turn off and unplug the appliance before cleaning or maintenance.
·Clean the surface of the appliance with a dry cloth.
·Do not use corrosive detergent or solvent to clean the appliance to avoid any
discolouration or damage.
·Do not swash with water.
·Do not use hard objects to clean the fan.
·Regular cleaning is suggested to avoid dirt blockage that may result in mechanical failure.
SPECIFICATION
WARRANTY
1. The product has 2 years warranty from the date of purchase.
2. The warranty shall not apply:
A. to any product subjected to misuse, alteration, act of God, improper handling, improper
transport, improper testing or unauthorized repair;
B. to cosmetic problems or defects which result from normal wear and tear under ordinary
use yet not affecting the performance or use of the product;
C. if the product is disassembled or altered;
D.to any packing, transportation, export / import tax or any related expenses.
Within warranty coverage period, all checking, repair and spare parts cost will be waived
for those defects arising from normal usage. Free replacements of spare parts do not
include the following:
Any filter, outer cabinet, plastics accessories
Product not used for personal or domestic purpose
-8 -

3. CUSTOMER MUST PRESENT THE SALES INVOICE OR RECEIPT FOR 2 YEAR WARRANTY
SERVICES.
4. Please bring along the product and sales invoice or receipt to our services center for
warranty services during office hour:
Address
Service Hotline
Service Hours:
Monday-Friday
Saturday
Sunday & Public
Holiday
:
:
:
:
:
Unit A, 20/F, Yip Shing Industrial Centre, No.19, Yip Shing
Street, Kwai Chung.
(852) 2428 1500
9:00am - 6:00pm
9:00am - 4:00pm
Closed
NOTES
To prevent circuit overload and fire, no more than one safety compliant adaptor or
extension unit should be inserted into a socket outlet. (Do not connect other appliances to
the socket outlet supplying an electric heater.) No adaptor should be inserted into any
extension unit or vice versa.
Stop using an adaptor or an extension unit or a socket if its socket holes cannot firmly hold
a plug if it is too hard to insert a plug into it.
This appliance must be plugged into a specific 220-240V~ socket. Please make sure the
plug is fully plugged-in before use. Do not use any adapter or extension cord; never use
the same supply socket for this appliance and other appliances at the same time, in order
to avoid damage to this appliance.
THE APPLIANCE IS FOR HOUSEHOLD USE ONLY.
ENVIRONMENT
Do not throw away the appliance with the normal household waste at the end of its life, but hand
it in at an official collection point for recycling. By doing this, you help preserving the
environment.
IMPORTANT NOTICES
IN NO EVENT SHALL OUR COMPANY OR THE SUPPLIER BE LIABLE TO YOU OR ANY OTHER PARTY FOR
ANY DIRECT, INDIRECT, GENERAL SPECIAL, INCIDENTAL, CONSEQUENTIAL, EXEMPLARY OR OTHER
DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PRODUCT (INCLUDING, WITHOUT
LIMITATION, DAMAGES FOR INJURY, LOSS OF PROPERTY, BUSINESS PROFITS, BUSINESS INTERRUPTION)
OR FROM ANY BREACH OF WARRANTY, EVEN IF OUR COMPANY OR SUPPLIER HAS BEEN ADVISED OF
THE POSSIBILITY OF SUCH DAMAGES. IN NO CASE SHALL OUR COMPANY OR SUPPLIER'S LIABILITY
EXCEED THE AMOUNT YOU PAID FOR THE PRODUCT.
Specifications, designs and dimensions are subject to change without prior notice.
-9 -