Turn of the century 20345 User manual

9191 • 010617

52”ALMENA

CEILING FAN

Owner’s Manual

Models #20345

Turn of the CenturyTM

If a problem cannot be remedied or you are experiencing diculty in installation,

please contact the Service Department: 1-877-459-3267, 9 a.m.- 5 p.m. Central time.

Turn of the Century

PACKAGE CONTENTS

HARDWARE CONTENTS

26 29

1. Canopy

2. Canopy Cover

3. Mounting Bracket

4. Downrod

5. Downrod Pin

6. Downrod Clip

7. Yoke Cover

8. Motor Assembly

9. Fitter Plate

10. Light Kit

11. Plastic Spacer

12. Finial Cap

13. Finial

14. Ribbed Glass

15. Glass Bowl

16. Pull Chain Extension (x 2)

17. E-26 Bulb (x 3)

18. Blade (x 5)

19. Blade Arm (x 5)

20. Hardware Kit

21. Owner’s Manual

22. Motor Screw (x 10)

23. Mounting Bracket

Screw(x 4)

24. Blade Screw (x 15)

25. Closemount Screw (x 3)

26. Set Screw (x 2)

27. Blade Washer (X 15)

28. Fitter Plate Screw (x 3)

29. Wire Connector (x 3)

Unpack your fan and check the contents. You should

have the following items:

PACKAGE CONTENTS

HARDWARE CONTENTS

Note: Some extra hardware has been included. The quantity

listed above is the number required for installation.

13 12

Turn of the Century

MOUNTING OPTIONS

Triple Mount Drawing

Closemount

Downrod Mount

Slope Ceiling Mount (Up to 16 degrees)

A. 14.1 in. B. 8.82 in. C. 8.24 in. D. 5.01 in.

DIMENSION REFERENCE

Choose one of the following mounting options:

Closemount method is best suited for ceilings lower than 8 feet. It does not utilize the downrod.

Downrod Mount is best suited for ceilings 8 ft. or higher. For taller ceilings you may want to use a longer

downrod (sold separately).

Angled Ceiling Mount is best suited for angled or vaulted ceilings. A longer downrod is sometimes necessary to

ensure proper blade clearance from the ceiling. If using the angle mount, check to ensure the ceiling angle is not

steeper than 16°.

Turn of the Century

WARNING

READ ALL SAFETY INFORMATION AND INSTALLATION INSTRUCTIONS BEFORE YOU BEGIN INSTALLING THE

FAN AND SAVE INSTRUCTIONS.

All set screws of the fan must be checked and retightened where necessary before installation.

To reduce the risk of personal injury, do not bend the blade brackets when installing the brackets, balancing

the blades or cleaning fan. Do not insert foreign objects in between rotating fan blades.

Before changing the fan direction, turn o the fan and wait for the fan blades to stop completely.

The safeguards provided by these safety instructions and by the separate installation instructions are not

meant to cover all possible conditions and situations that may occur. It must be understood that common

sense, caution and care are factors which can not be built into this product. These factors must be supplied

by the person(s) installing, caring for and operating the fan.

TO AVOID RISK OF ELECTRIC SHOCK, BE SURE TO SHUT OFF POWER AT THE MAIN FUSE OR CIRCUIT

BREAKER BOX BEFORE INSTALLING OR SERVICING THIS FIXTURE. TURNING OFF THE ELECTRICAL POWER

BY USING THE LIGHT SWITCH IS NOT SUFFICIENT TO PREVENT ELECTRICAL SHOCK.

TO REDUCE THE RISK OF INJURY, INSTALL THE FAN SO THAT THE BLADES ARE AT LEAST 7 FEET (2.1

METERS) ABOVE THE FLOOR AND AT LEAST 18 INCHES (0.5 METERS) FROM THE TIP OF THE BLADES TO

THE WALL.

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR PERSONAL INJURY, MOUNT TO OUTLET BOX

MARKED “ACCEPTABLE FOR FAN SUPPORT” AND USE MOUNTING SCREWS PROVIDED WITH THE OUTLET

BOX.

THE INSTALLATION HAS TO BE IN ACCORDANCE WITH THE NATIONAL ELECTRICAL CODE, ANSI/NFPA

70-1999 AND LOCAL CODES. IF YOU ARE UNFAMILIAR WITH THE METHODS OF INSTALLING ELECTRICAL

WIRING, SEEK THE SERVICES OF A QUALIFIED LICENSED ELECTRICIAN.

SAFETY INSTRUCTIONS

IMPORTANT:

Before you begin installing or using the fan, carefully read the entire manual. If unsure about any part of the

installation, contact a qualied electrician.

Save all instructions.

NOTE: The fan weight is Net Weight: 21.5 lb (9.7 kg). Be sure the outlet box (not included) is securely attached to

the building structure and is marked “Acceptable For Fan Support”. Failure to do so can result in serious injury.

Turn of the CenturyTM

ASSEMBLY INSTRUCTIONS

1. Turn OFF the electrical power at the main fuse or circuit

breaker.

3. CLOSEMOUNT INSTALLATION (OPTIONAL)

a. Remove the canopy cover from the bottom of the

canopy.

b. Remove the three Phillips-head closemount screws from

the top of the motor assembly.

c. Align the holes in the bottom of the canopy with the

screw holes in the top of the motor housing. The larger

holes in the canopy will encompass the three pre-installed

screws.

d. Secure the canopy to the top of the motor housing with

the closemount screws.

e. Hang the fan on the hook of the mounting bracket.

Proceed to Step 8.

Closemount

Screw

Canopy

Mounting

Bracket

2. Remove the canopy from the mounting bracket by

removing the two mounting bracket screws from the

round holes in the canopy and save for later use. Then

loosen the other two mounting bracket screws from

the L-shaped slots. Install the mounting bracket to the

outlet box (not included) using the screws and washers

provided with the outlet box.

Warning: To reduce the risk of re electric shock,

or personal injury, mount to the outlet box marked

“acceptable for fan support” and use the mounting

screws and washers provided with the outlet box.

If you wish to use the Downrod Mount (as shown on

page 3), proceed to Step 5.

Mounting

Bracket Screw

DOWNROD MOUNT

4. Remove the downrod pin and downrod clip from the

downrod. Then, loosen but don’t remove the two set

screws in the yoke of the motor assembly.

Downrod Clip

Yoke

Set Screw

Downrod

6Turn of the CenturyTM

ASSEMBLY INSTRUCTIONS

5. Feed the wires coming from the yoke through the yoke

cover, canopy and out through the top of the downrod.

6. Insert the downrod into the yoke and reinstall the

downrod pin and downrod clip. Then retighten the two

set screws.

Note: With wires extending out of the downrod,

measure 8 inches of lead wire and cut the excess wire

with wire cutters (not included). Then strip 1/2” of

insulation from the end of each wire.

Downrod

Canopy

Yoke Cover

Downrod Pin

Set Screw

Yoke

Downrod

Downrod Clip

Yoke

7. With wiring extending out of the downrod, measure

eight inches of lead wire and cut the excess wire with

wire cutters (not included). Then strip 1/2” of insulation

from the end of each wire. Then, lift the downrod into the

mounting bracket. Rotate the downrod until the tab in the

mounting bracket is seated in the slot in the downrod ball.

WARNING: The fan should not rotate in the mounting

bracket if installed correctly. Failure to align the slot in the

downrod ball with the tab on the mounting bracket may

result in fan falling causing serious injury or death.

Mounting

Bracket

Tab

Slot

Downrod

7Turn of the CenturyTM

ASSEMBLY INSTRUCTIONS

Black (Hot)

Wire Connector

White (Neutral)

Bare/Green (Ground)

Black

Blue

White

Green

99. Raise the canopy, ensuring the two mounting bracket

screws are aligned with the J-shaped slots in the canopy.

Then turn the canopy clockwise until the mounting

bracket screws are completely engaged in the J-shaped

slots. Install the two previously removed mounting

bracket screws in the round holes.

Securely tighten all four mounting bracket screws.

10. Partially insert three blade screws, along with the

blade washers, through the blade and into the blade arm.

Tighten each blade screw, starting with the one in the

middle. Repeat this step for the remaining blades and

blade arms.

8. Use wire connectors to connect the fan wires to the

power supply wires according to the wiring diagram and

the following instructions:

• Connect the white wire from the fan to the white (neutral/

common) supply wire.

• Connect the black and blue wires from the fan to the

black (hot/power) supply wire.

• Connect the green wire from the fan and the mounting

bracket to the bare/green (ground) supply wire.

Note: If a second hot power wire is available from the

outlet box, connect it to the blue (light power) fan wire for

separate fan and light switches.

Important: After the connections have been made, the

wires should be turned upward and pushed carefully

up into the outlet box. Place the black and white wire

connections on opposite sides of the outlet box.

Canopy

J-shaped Slot

Round

Hole

Blade

Arm

Blade Screw

Blade Washer Blade

Mounting

Bracket Screw

Blade Arm

Motor Screw

Hole

Motor

Assembly 11

11. Secure the blade arm to the underneath side of the

motor using motor screws removed in Step 3 and blade

isolators. Completely secure each blade arm to motor

assembly before moving to the next. Note: The notch in

the tter plate allows access for a Phillips screwdriver.

8Turn of the CenturyTM

ASSEMBLY INSTRUCTIONS

Light Kit

Hex Nut

Finial Cap

Finial

Bulb

Plastic Spacer Rubber Washer

Rubber Washer

Plastic Spacer

Hex Nut

Ribbed Bowl

12. Remove one of the three tter plate screws and tter

from the tter plate and loosen the other two. Then,

connect the 9-pin connector from the fan to the 9-pin

connector from the light kit.

9-pin

Connector

Light Kit

Fitter Plate Screw

Keyhole Slot

13. Lift the light kit and place the two keyhole slots in the

light kit over the two loosened tter plate screws. Turn

the light kit clockwise and secure it to the tter plate

with the previously removed tter plate screw. Tighten all

three screws.

14. Remove the nial, nial cap, hex nut, plastic spacer

and rubber washer from the threaded rod at the bottom

of the light kit.

Install the three E26-base bulbs into the sockets of the

light kit.

15. Lift the ribbed bowl up until the top edge is seated in

the top rim of the light kit. Feed the pull chain through

the rubber washer and plastic spacer and secure with hex

nut. Note: The concave side of the plastic spacer will face

downward so that the hex nut will t inside.

9Turn of the CenturyTM

Finial Cap

Glass Bowl

Pull Chain Extension

Finial

ASSEMBLY INSTRUCTIONS

16. Feed the pull chains through the appropriate holes in

the glass bowl. Then, lift the glass bowl over the threaded

rod until it is ush with the plastic spacer. Lift the nial cap

onto the threaded rod and secure with the nial.

18. Restore the power at the main fuse or circuit breaker.

17. Attach pull chain extension(s) to the pull chain(s).

10 Turn of the CenturyTM

OPERATING INSTRUCTIONS

2. Using a ceiling fan will allow you to raise your

thermostat setting in summer and lower your thermostat

setting in winter without feeling a dierence in your

comfort.

Note: To access the reverse switch, turn o the fan and

remove the ribbed glass and the glass bowl.

IMPORTANT: The reverse switch must be set either

completely left or right in order for the fan to function

correctly. If the reverse switch is set in the middle

position, the fan will not operate.

1. The fan pull chain is located in the o-center hole in the

nial cap. It has four positions to control fan speed. One

pull is HIGH, two is MEDIUM, three is LOW and four turns

the fan OFF. The light pull chain is located in the center of

the nial. It turns the light ON and OFF.

Fan Pull

Chain

Reverse Switch

Light Pull

Chain

Table of contents

Other Turn of the century Fan manuals

Turn of the century

Turn of the century 355-6786 User manual

Turn of the century

Turn of the century 20587 User manual

Turn of the century

Turn of the century 20186 User manual

Turn of the century

Turn of the century 355-1792 User manual

Turn of the century

Turn of the century Midori20337 User manual

Turn of the century

Turn of the century SENECA 20306 User manual

Turn of the century

Turn of the century 20564 User manual

Turn of the century

Turn of the century 20564 User manual

Turn of the century

Turn of the century 355-3001 User manual

Turn of the century

Turn of the century Menards SKU 355-1844 User manual

Turn of the century

Turn of the century 355-6777 User manual

Turn of the century

Turn of the century Walnut Grove Ceiling Fan User manual

Turn of the century

Turn of the century Knit User manual

Turn of the century

Turn of the century Nevis 355-1857 User manual

Turn of the century

Turn of the century SKU 355-7529 User manual

Turn of the century

Turn of the century 35072 User manual

Turn of the century

Turn of the century Elise Owner's manual

Turn of the century

Turn of the century 355-6776 User manual

Turn of the century

Turn of the century 20554 User manual

Turn of the century

Turn of the century 20261 User manual

Turn of the century

Turn of the century 20200 User manual

Turn of the century

Turn of the century EF200M-52 User manual

Turn of the century

Turn of the century 20501 User manual

Turn of the century

Turn of the century 20223 User manual

Popular Fan manuals by other brands

Minka Group

Minka Group minkaAire Wave F843 instruction manual

Airflow

Airflow Adroit DV50 instruction manual

Vornado

Vornado 270 Series owner's guide

comfort air

comfort air TH-10D instruction manual

Livoo

Livoo DOM386 instruction manual

Holmes

Holmes BLIZZARD HAOF-90 owner's guide

Taurus

Taurus GRECO 16 ELEGANCE manual

Quorum

Quorum PINNACLE installation instructions

Monte Carlo Fan Company

Monte Carlo Fan Company 3DIR58RBD-V1 Owner's guide and installation manual

Craftmade

Craftmade UH52 installation guide

Jocel

Jocel JVA030658 instruction manual

MIKA

MIKA MFB1211/GR user manual

Harbor Breeze

Harbor Breeze RLG52NWZ5L manual

Allen + Roth

Allen + Roth L1405 instruction manual

ViM

ViM KUBAIR F400 ECOWATT Technical manual

HIDRIA

HIDRIA R10R-56LPS-ES50B-04C10 user guide

BLAUBERG Ventilatoren

BLAUBERG Ventilatoren CENTRO-M 100 L user manual

Triangle Engineering

Triangle Engineering HEAT BUSTER SPL Series owner's manual