Fortune Z-Wave Plus v2 User manual

AYRMODZW34MNL0050
ISL000000000
We’re here to help, 24/7 18552135841 [email protected] support.shopyalehome.com
Smart Module Installation
ZWave Plus™v2 Assure Lock®2
Models: YRD410, YRD420, YRD430, YRD450, YRD420F, YRD450F
If your lock is already installed,
remove the batteries.
Insert the Yale ZWave Plus™ v2
Smart Module into the battery
compartment slot.
Reinsert the batteries.
Open the Yale Access App and
navigate to your lock model.
3a. Select ‘Lock Settings’.
3b. Select ‘Yale Smart Module’.
3c. Follow steps in the app
to complete set-up.
To remove the Yale ZWave Plus™ v2
smart module from your system,
select the disconnect ZWave™
option from lock settings
in the Yale Access App.
1 2 3 4
NOTE: Anytime you add or remove a Smart Module from your lock, the batteries must be removed.
Anytime you add or remove a
Smart Module from your lock,
the batteries must be removed
Smart Module Installation
ZWave Plus™v2 Assure Lock®
Models: YRD216, YRD226, YRD256, YRL226, YRL216
If your lock is already installed,
remove the batteries.
Insert the Yale ZWave Plus™ v2
Smart Module into the battery
compartment slot.
Reinsert the batteries.
If you have SmartStart enabled
with your ZWave™ system,
follow in-app prompts to add a
new device. If you do not have
SmartStart or are not sure,
follow the steps below.
3a. Enter your locks master entry
code, followed by the
3b. Press the 7key followed by
the
3c. Press the 1key followed by
the
To remove the ZWave Plus™ v2
Smart Module from your system,
open the smart home
or alarm app and follow the
instructions for removing a device.
4a. Enter your locks master entry
code, followed by the
4b. Press the 7key followed by the
4c. Press the 1key followed by the
1 2 3 4
Anytime you add or remove a
Smart Module from your lock,
the batteries must be removed
If prompted,
scan QR code

This device is a security enabled ZWave Plus™
v2 product that is able to use encrypted ZWave
Plus™ v2 messages to communicate to other
security enabled ZWave Plus™ v2 products.
This device must be used in conjunction with
a Security Enabled ZWave™ Controller in order
to fully utilize all implemented functions.
This product can be operated in any ZWave™
network with other ZWave™ certified devices
from other manufacturers. All non-battery
operated nodes within the network will act
as repeaters regardless of vendor to increase
reliability of the network.
Changes or modifications to this device,
not expressly approved by
MASTER LOCK Group
could void the user’s authority
to operate the equipment.
FCC:
Class B Equipment
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful Interference to
radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS.
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE,
AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE
RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE
UNDESIRED OPERATION.
This equipment complies with the FCC radiation limits set forth for
an uncontrolled environment. This equipment should be installed
and operated with minimum distance 20cm between the radiator
& your body.
Industry Canada:
Section 7.1.2 of RSSGEN Under Industry Canada regulations,
this radio transmitter may only operate using an antenna of a type
and maximum (or lesser) gain approved for the transmitter by
Industry Canada. To reduce potential radio interference to other
users, the antenna type and its gain should be so chosen that the
equivalent isotropically radiated power (e.i.r.p.) is not more than t
hat necessary for successful communication.
En vertu des règlements d’Industrie Canada, cet émetteur radio
ne peut fonctionner avec une antenne d’un type et un maximum
(ou moins) approuvés pour gagner de l’émetteur par Industrie
Canada. Pour réduire le risque d’interférence aux autres utilisateurs,
le type d’antenne et son gain doivent être choisies de façon que la
puissance isotrope rayonnée équivalente (PIRE) ne dépasse pas ce
qui est nécessaire pour une communication réussie.
Section 7.1.3 of RSSGEN This Device complies with Industry Canada
License-exempt RSS standard(s). Operation is subject to the
following two conditions: 1) this device may not cause interference,
and 2) this device must accept any interference, including
interference that may cause undesired operation of the device.
Cet appareil est conforme avec Industrie Canada RSS standard
exemptes de licence(s). Son fonctionnement est soumis aux
deux conditions suivantes: 1) ce dispositif ne peut causer des
interférences, et 2) cet appareil doit accepter toute interférence,
y compris les interférences qui peuvent causer un mauvais
fonctionnement du dispositif.
CAN ICES3B/NMB3B
24/7 18552135841 Yale Home ShopYaleHome.com
Yale® is a registered trademarks of Master Lock Company LLC and its affiliates. Other products’ brand names may be trademarks or registered trademarks of their respective owners
and are mentioned for reference purposes only. © Copyright 2023. All rights reserved. Reproduction in whole or part without the express written permission of Master Lock Company LLC
and its affiliates is prohibited.

P/N YRD604-KD-BLE-0047 Rev A
Yale Pro2
Keyed YRD614 / YRD624
Download Yale Access App
Create an account if you don’t already have
one, and tap “Set Up a Device”.
Note: If you have an account with the August App, use the same username and
password for the Yale Access App.
Install Your Lock
Follow the step-by-step Installation Guide in this manual (pages 923),
or refer to the app for installation instructions with helpful videos.
Note: If you use the app, please tear off the Door Checker and the Marking
Template (pages 58) to use when prompted.
Set Up and Use Your Lock
Create permanent entry codes, issue entry codes for guests, operate
your lock with your phone and more (pages 2435).
Trusted Every Day ISL222500003

P/N YRD604-KD-BLE-0047 Rev A

P/N YRD604-KD-BLE-0047 Rev A
Contents
In the Box 4
Door Checker 5
Marking Templates 7
Installation Guide 9
Remove Existing Deadbolt 10
Check Door Measurements 11
Make or Adjust Holes 12
Install Deadbolt Latch 13
Install Exterior Keypad 14
Install Mounting Plate 15
Attach Wire Cable to Interior Lock 16
Install Interior Lock 17
Test Thumbturn and Key 18
Install Yale Smart Module (Optional) 19
Install DoorSense (Optional) 20
Install Batteries and Replace Cover 23
Using Your Lock 24
Connecting to Your Lock 25
Creating and Managing Entry Codes 26
Set Up HomeKit (Optional) 27
LED Alerts 28
Resetting Your Lock to Factory Defaults 29
Features 30
App Settings 31
Lock Operations Troubleshooting 33
Hardware Troubleshooting 35

4
P/N YRD604-KD-BLE-0047 Rev A
In the Box
Lock Hardware
b.
c.
d.
e.
X 4
X 4
X 2
X 2
X 2
X 2
X 2
Add-Ons
123
5 76
4
UP
1. Exterior Keypad
2. Interior Lock
3. Strike Plate
4. Adjustable Deadbolt & Key
5. Manual
6. Reset Pin
7. Mounting Plate
8. AA Batteries
9. Screws
a. Strike Plate and Deadbolt Screws
b. Teal Screw Set B
c. Black Screw Set C
d. Silver Screw Set D
e. Optional Security Strike Plate Screws
10. DoorSense
a. Housing
b. Cover
c. Mounting Tape
d. Screws
e. Flush Mount Cap
11. Smart Module
(Included with select models)
8
10 9
11
a. a.d.
e.b.
c.
AA

5
P/N YRD604-KD-BLE-0047 Rev A
Tear Along the Dotted Line
Door Checker Part 1
Measure Clearance Measure Door Thickness Measure Backset
A. 2” minimum clearance between top
of the door knob and center of deadbolt
hole.
B. 13/8” door thickness; use teal
(shortest) screws.
C. 13/8” - 13/4” door thickness;
use black (medium) screws.
D. 13/4” - 21/4” door thickness;
use silver (longest) screws.
E. 23/8” backset, use out of box latch
setting.
F. 23/4” backset, adjust latch setting
(Step 2, point 1 of this manual).
Greater than A B, C or D Equals E or F
Less than A Less than B or
greater than D
Doesn’t equal E or F
(Your door is not a match)
(Your door is not a match)
(Your door is not a match)
10 2 3 4 5
6
Door Checker Part 1
v
B A D
C E
v
v
See Reverse for Part 2
1/8 1/8 1/8 1/8 1/83/8 3/8 3/8 3/8 3/85/8 5/8 5/8 5/8 5/87/8 7/8 7/8 7/8 7/8
1/4 1/4 1/4 1/4 1/4
1/2
10 2 3 4 5
1/2 1/2 1/2 1/2
3/4 3/4 3/4 3/4 3/4
B A E
DC F

6
P/N YRD604-KD-BLE-0047 Rev A
Tear Along the Dotted Line
Door Checker Part 2 See Reverse for Part 1
Measure Face Bore
Equals G or H
Less than G Less than I
G. 11/2” face bore diameter.
H. 21/8” face bore diameter.
Measure Edge Bore and Strike Pocket
I. 1” edge bore diameter;
1” strike pocket diameter and depth.
Equals I
Greater than IGreater than H
(Adjust diameter to G or H) (Adjust diameter to I)
(Your door is not a match)(Your door is not a match)
(Edge Bore)Door (Strike Pocket) Frame
Diameter Depth
Minimum strike pocket depth is 1”.
HI G
1/8 1/8 1/8 1/8 1/83/8 3/8 3/8 3/8 3/85/8 5/8 5/8 5/8 5/87/8 7/8 7/8 7/8 7/8
1/4 1/4 1/4 1/4 1/4
1/2
10 2 3 4 5
1/2 1/2 1/2 1/2
3/4 3/4 3/4 3/4 3/4

7
P/N YRD604-KD-BLE-0047 Rev A
Tear Along the Dotted Line
Marking Template for 21/8” (54mm) Face Bore
Center of
1” (25mm)
Edge Bore
Center of
1” (25mm)
Edge Bore
Centerline
Center of
21/8” (54mm)
Face Bore
Center of
21/8” (54mm)
Face Bore
I H
13/8” (35mm)
Door Thickness
B23/8” (60mm)
Backset
E
13/4” (44.5mm)
Door Thickness
C23/4” (70mm)
Backset
F
21/8”

8
P/N YRD604-KD-BLE-0047 Rev A
Marking Template for 11/2” (38mm) Face Bore
Center of
1” (25mm)
Edge Bore
Center of
1” (25mm)
Edge Bore
Centerline
Center of
11/2” (38mm)
Face Bore
Center of
11/2” (38mm)
Face Bore
11/2”
I G
13/8” (35mm)
Door Thickness
B23/8” (60mm)
Backset
E
13/4” (44.5mm)
Door Thickness
C23/4” (70mm)
Backset
F
Tear Along the Dotted Line

9
P/N YRD604-KD-BLE-0047 Rev A
Installation Guide
Required Tools You Might Also Need
Failure to follow the Installation Guide precisely could result in damage to the product,
voiding the factory warranty, and could lead to failure of the product to provide access.
1. Phillips Head Screwdriver
2. Door Checker
(tear off pages 56 of this manual)
3. Tape Measure
4. Drill
5. Marking Template
(tear off pages 78 of this manual)
6. Pencil
7. Wood Mortise Chisel
8. Utility Knife
9. Level
10 2 3 4 5 6
Door Checker Part 1
v
B A D
C E
1 3
5
8
7
9
6
4
2

10
P/N YRD604-KD-BLE-0047 Rev A
Frame Door
Keep your old deadbolt until your new lock has been successfully installed.
1a Remove Existing Deadbolt
If you have a new door, please proceed to step 1b.
If you have a deadbolt on your door, use the diagram to help you remove it.

11
P/N YRD604-KD-BLE-0047 Rev A
If you have confirmed that the existing holes are compatible with your new lock, please proceed to step 2 (skip step 1c).
If you need to make adjustments, go to
step 1c and find the closest match to each
aspect of your door on the Marking Template.
Tear off the Door Checker (pages 56) and follow the guidelines on both sides to
measure each aspect of your door and frame. There are some cases when existing
holes cannot be adjusted to be compatible.
Please do not drill any holes until you confirm that your door is compatible.
10 2 3 4 5 6
Door Checker Part 1
v
B A D
C E
10 2 3 4 5 6
Door Checker Part 2
H F G
1b Check Door Measurements
If your door doesn’t have holes, please proceed to step 1c.

12
P/N YRD604-KD-BLE-0047 Rev A
1c Make or Adjust Holes
Skip this step if you have confirmed that the existing holes are compatible (step 1b).
1. Tear off the Marking Template (pages 78), and choose the
preferred face bore diameter (2- 1/8” or 11/2”) on either side
of the template.
2. Tape the Marking Template onto the door as shown.
3. Check the door thickness. It should match either the shape
with solid outlines (13/4”), or the one with dashed outlines
(13/8”).
3a. Use solid lines as a template for 13/4” door thickness.
3b. Use dashed lines for 13/8” door thickness.
4. Choose your preferred backset. It should match either the
shape with solid outlines (23/4”), or the one with dashed
outlines (23/8”).
4a. Use solid lines as a template for 23/4” backset.
4b. Use dashed lines for 23/8” backset.
5. Drill holes in your door where marked.
1
2
3a
4
3b
4a
4b
3
6. On the door frame, align the center of the strike plate with the
center of the edge bore. Trace the strike plate, then chisel to the
depth of the strike plate so it sits flush with your door frame. Drill
the 1” diameter strike pocket with a minimum depth of 1”.
6
Frame Door

13
P/N YRD604-KD-BLE-0047 Rev A
1. Correct deadbolt length is based on the backset. Refer to measurements
Eand Fon the Door Checker (page 5) to verify backset.
2. Align strike plate with deadbolt latch.
2a. (Optional) Security screws can be used in place of
the small strike plate screws.
3. Make sure UP arrow on the deadbolt is facing upwards.
4. Deadbolt latch must be in an unlocked position.
Note: If the deadbolt latch is extended, use a small flathead
screwdriver to rotate slot until deadbolt latch is retracted.
x 2 for Deadbolt Latch
x 2 for Strike Plate
(Actual size)
2 Install Deadbolt Latch
2-3/4 2-3/8 UP
23/8” Backset
(Out of box)
E
2-3/4 2-3/8 UP
23/4” Backset
(To adjust, twist neck by holding the body stable)
F
2a
2
3
4
Minimum strike pocket depth is 1”.

14
P/N YRD604-KD-BLE-0047 Rev A
1
Install your lock with the door open.
Do not close your door until all the steps are completed.
1. Refer to measurements G and H on the Door Checker (page 6) to measure face
bore hole. If the hole is 11/2” (G), unscrew the two small screws and remove the
adapter.
2. Make sure your deadbolt latch is in an unlocked position. Refer
to step 2, point 4 (page 13) for guidance on how to retract it, if
needed.
3. Slide the tailpiece through the deadbolt latch slot, making sure
the keypad is on the exterior part of your door.
4. Guide the wire cable under the deadbolt.
5. Slide the keypad in place. Hold or secure in place until the
mounting plate is installed in the next step.
4
5
3
3 Install Exterior Keypad
2

15
P/N YRD604-KD-BLE-0047 Rev A
1. Refer to measurements B, C, and Don the Door Checker (page 5) to select screws.
2. Route the wire cable into the designated slot in the mounting plate.
3. Guide posts of the mounting plate into the holes on the exterior keypad.
4. Slide tailpiece through the designated slot in the mounting plate.
5. Tighten screws with a screwdriver to secure the mounting plate. As you tighten
the screws, make sure the mounting plate and the keypad are straight.
x 2 Teal Screws (13/8” door thickness)
x 2 Black Screws (13/8” - 13/4” door thickness)
x 2 Silver Screws (13/4” - 21/4” door thickness)
B
2
3
4
5
C
D
4 Install Mounting Plate
Ensure that the wire cable is not pinched to prevent it from
reducing your lock’s battery life.

16
P/N YRD604-KD-BLE-0047 Rev A
1. Remove battery cover by pulling it upwards off the body of the
interior lock.
2. Make sure the side of the cable end with the ridges and the
marked line faces outward.
3. Push cable into the designated slot until you hear a click.
2
1
3
5 Attach Wire Cable to Interior Lock

17
P/N YRD604-KD-BLE-0047 Rev A
1. Make sure the tailpiece slot is in horizontal position. Use the
thumbturn to adjust if needed.
2. Slide the tailpiece through the designated slot on the back of the
thumbturn.
3. Press the lock against the mounting plate, adjusting its position until
it clicks into place and the bottom of the lock is held in place.
4. Tighten the two pre-installed screws.
3
When fully tightened, lock should be flush to door.
6 Install Interior Lock
2
1
4

18
P/N YRD604-KD-BLE-0047 Rev A
If deadbolt latch does not lock or unlock with the key (from the outside) or the
thumbturn (from the inside):
• Ensure that the deadbolt latch is centered in the face bore hole;
• Ensure that the tailpiece is positioned horizontally and inserted through
deadbolt latch slot (step 3, point 3) into the thumbturn slot (step 6, point 2).
Smooth deadbolt latch operation will enhance your battery life.
7 Test Thumbturn and Key